Related Manuals for Toro Flex-Force Power System 51835T
Summary of Contents for Toro Flex-Force Power System 51835T
- Page 1 Form No. 3460-819 Rev A Flex-Force Power System ™ MAX String Trimmer Model No. 51835T—Serial No. 323000001 and Up *3460-819* Register at www.Toro.com. Original Instructions (EN)
- Page 2 This trimmer is intended to be used by residential homeowners to trim grass as needed outdoors. It is designed to use Toro 60V lithium-ion battery packs. These battery packs are designed to be charged only by Toro 60V lithium-ion battery chargers. Using this product for purposes other than its intended use could prove dangerous to you and bystanders.
-
Page 3: Safety Alert Symbol
II. Preparation Keep bystanders and children away from the operating area. Use only the battery pack specified by Toro. Using other accessories and attachments may increase the risk of injury and fire. Plugging the battery charger into an outlet that is not 100 to 240 V can cause a fire or electric shock. - Page 4 Charge the battery pack with only the battery Do not overreach—Keep proper footing and charger specified by Toro. A charger suitable for balance at all times, especially on slopes. Walk, one type of battery pack may create a risk of fire never run with the tool.
- Page 5 instructions, have an Authorized Service Dealer repair or replace a damaged guard or part. Do not replace the existing non-metallic cutting means on the tool with a metallic cutting means. Do not attempt to service or repair the tool, battery pack, or battery charger except as indicated in the instructions.
-
Page 6: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal139-5220 139-5220 1. Do not discard improperly. decal139-8263 139-8263 1. - Page 7 Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Allen wrench Unfold the shaft. Auxiliary handle assembly Install the auxiliary handle. Guard Install the guard. Unfolding the Shaft Parts needed for this procedure: Allen wrench Procedure Unfold the shaft (A of...
- Page 8 g280969 Figure 3...
-
Page 9: Installing The Auxiliary Handle
Installing the Auxiliary Handle Parts needed for this procedure: Auxiliary handle assembly Procedure Separate the auxiliary handle from the handle plate by removing the 4 socket head screws using the provided Allen wrench (A of Figure Line up the guides on the auxiliary handle plate to the guide on the bottom of the trimmer shaft (B of Figure Line up the auxiliary handle with auxiliary handle plate on the trimmer shaft (C of Figure... -
Page 10: Installing The Guard
Installing the Guard Parts needed for this procedure: Guard Procedure Using the provided Allen wrench, remove the 2 socket head screws, 2 washers, and 2 spacers from the trimmer base (A of Figure Align the guard onto the trimmer base (B of Figure Secure the guard onto the base of the trimmer with the 2 socket head screws, 2 washers, and 2 spacers previously removed (C of... -
Page 11: Product Overview
Authorized Service Dealer or authorized Toro 3. Auxiliary handle 6. String distributor or go to www.Toro.com for a list of all approved attachments and accessories. To ensure optimum performance and continued safety certification of the machine, use only genuine Toro replacement parts and accessories. -
Page 12: Operation
Operation Starting the Trimmer Make sure that the vents on the trimmer are clear of any dust and debris. g268420 Figure 9 1. Speed range switch 3. Variable-speed trigger 2. Lockout trigger Shutting Off the Trimmer To shut off the trimmer, release both triggers. Whenever you are not using the trimmer or are transporting the trimmer to or from the work area, remove the battery pack. -
Page 13: Advancing The Line Manually
Advancing the Line Using the Bump Feed Run the tool at full throttle. Tap the bump button on the ground to advance the line. The line advances each time the bump button is tapped. Do not hold the bump button on the ground. -
Page 14: Operating Tips
Adjusting the Cutting Swath The trimmer comes from the factory with a cutting swath of 36.6 cm (14 inches) as shown in A of Figure Refer to the following instructions to adjust the swath to 40.6 cm (16 inches) as shown in D of Figure Remove the swath blade from the bottom of the guard by removing the 2 screws holding it in place using the provided Allen wrench (B of... -
Page 15: Maintenance
Replacing the String Use only 2 mm (0.080 inch) monofilament string (Toro Part No. 88201) or 2.4 mm (0.095 inch) twisted monofilament string (Toro Part No. 88202). Remove the battery pack. Remove any old string on the spool by... - Page 16 Storage Important: Store the tool, battery pack, and charger only in temperatures that are within the appropriate range; refer to Specifications (page 11). Important: If you are storing the battery pack for the off-season, charge it until 2 or 3 LED indicators turn green on the battery.
-
Page 17: Troubleshooting
Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair work must be performed by an authorized service center or a similarly qualified specialist if you cannot solve the problem yourself. Always remove the battery from the tool when troubleshooting, inspecting, maintaining, or cleaning the tool. Problem Possible Cause Corrective Action... - Page 18 Notes:...
- Page 19 The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.