Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Cassese 910 JR
Summary of Contents for Cassese 910 JR
- Page 1 O W N E R S M A N U E L Cassese 910 JR Table top &CS 910 Joining machine Cassese® Zone i n d u s t r i e l l e 7 7 3 9 0 VERNEUIL L'ETANG - FRANCE...
-
Page 2: Table Of Contents
TABLE OF CONTENTS INTRODUCTION 1. Introduction Page 1 2. Accessories Page 1 3. Specifications Page 1 4. Options Page 1 5. Guarantee Page 1 SET U P 1. Inspection of contents 2. Assembly Page 3 3. Connecting the machine Page 3 SETTINGS 1. -
Page 3: Introduction
We congratulate you on your wise decision and thank you for your trust. The CS 910 is an underpinner which has been developed through extensive experience gained in the manufacture of the reputable Cassese machines. It enables perfect joining of rectangular frames and also various other forms including hexagons, octagons Frames are joined by means of metal wedges which are specially designed for perfect locking. - Page 4 FIGURE 1 R C P I N L X O BACK FENCES'ANGLE KNOB 1 i SET UP LEVER SETTING RING CLAMP BRACKET WEDGES DISTRIBUTOR (BLOCK H) CLAMP HANDLE ANGLE SET UP SCREW FENCES MANOMETER PLUNGER W O R K PLUNGER SPEED BUTTON P O S I T I O N ON/OFF VALVE TIMER BUTTON...
-
Page 5: Set Up
SET UP I - I N S P E C T I O N OF CONTENTS Please, inspect the contents of your box carefully. If you should note any crate damage, please notify the carrier immediately to file a claim. The following list of items should be found in your box LIST OF ITEMS : - 4 feet (for Junior model) -
Page 6: Settings
S E T T I N G S I - SETTING OF ASSEMBLY ANGLE (FIG 2 & 3) FOR A SQUARE FRAME Since your frame joiner will always work after a cutting material (your c h o p p e r , saw or c h o p service mouldings), it has to adapt itself to the cutting angle of the machine that was used before. -
Page 7: Selection Of Stapling Positions
IV - SELECTION OF STAPLING P O S I T I O N The CS 910 is designed to enable wedging of mouldings at 1 or 2 points, with one or several wedges stacked at each of these two positions. The choice must be made according to the width and the height of the moulding. -
Page 8: Changing The Wedge Cartridge
FIGURE 7 V I - C H A N G I N G THE CARTRIDGE (FIG 7 ) 1 - Pull back the wedge pusher spring (FIGURE 7- F) 2 - Remove the empty cartridge 3 - Insert the new cartridge in the wedge distributor's window making sure the cartridge is firmly against the distributor block. -
Page 9: Joining Of Frame
TIP/HINT : For production joining, it is recommended to reduce the distance of p l u n g e r P to a p p r o x 3 / 8 " f r o m the m o u l d i n g , using screw C, a n d to a c c e l e r a t e the f i r i n g of w e d g e s by adjusting b u t t o n T ( t o w a r d s +) (see FIGURE 1). -
Page 10: Maintenance
M A I N T E N A N C E HAMMER F I G U R E FiXGUIDE BLOCK H THE TWO PLATES ASSEMBLY SCREWS ARE FACTORY SET AND PINNED REP. 2 DON'T REPLACE THEM SEPARATELY ASSEMBLY SCREWS PROCEDURE : 1 - Remove the present wedge cartridge, 2 - Using the 3 mm Allen key, loosen the retaining screw from the bar at the front of block H, (see FIGURE 1) (from the side of the horizontal clamp) and remove the block H,... -
Page 11: Maintenance Of "Wedge Distributor" (Bloc H)
II - M A I N T E N A N C E OF "WEDGES D I S T R I B U T I O N " SECTION (bloc H) At regular intervals remove bloc H from the machine and clean it using compressed air (Figure 1 1). -
Page 12: Trouble Shooting
TROUBLE SHOOTING SOLUTIONS PAGE PROBLEM POSSIBLES CAUSES S. 1: Repeat setting and ensure clamping of C 1 : Moulding clamp setting is incorrect THE CLAMP DOES NOT P 4 - S I I I CLAMPTHEM0ULDING operating lever 1 THE RIGHT MOULDING S.2: Repeat setting of operating lever using lever H P 4 - §... -
Page 14: Pneumatic Diagram
PLUNGER SUB-ASSEMBLY STAPLING BUTTON (FIG 1-P) (FIG 1 V, Part 218 P) BRAKE CYLINDER PRESSURE GAUGE (Part 177 P) (FIG 1 - 0, Part 159 P) STAPLING CYLINDER PRESSURE REGULATOR SUB ASSEMBLY (FIG 1 - U, Part 161 P CLAMP CYLINDER (Part 197 P°...