Husqvarna T536LiXP Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Chainsaw
  5. T536LiXP
  6. Operator's manual
Husqvarna T536LiXP Operator's Manual

Husqvarna T536LiXP Operator's Manual

Hide thumbs Also See for T536LiXP:
Table of Contents

Advertisement

Quick Links

Download this manual
T536LiXP
EN
Operator's manual
2-31

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna T536LiXP

Summary of Contents for Husqvarna T536LiXP

  • Page 1 T536LiXP Operator's manual 2-31...

  • Page 2: Table Of Contents

    EC Declaration of Conformity........31 Introduction Product description Intended use Husqvarna T536LiXP is a chainsaw model with a battery This tree service product is for tree maintenance such motor. as pruning and disassemble of tree crowns. Work is constantly in progress to increase your safety Note: National regulations can restrict the operation of and efficiency during operation.
  • Page 3 9. Rope eyelet Warning! Kickback can occur when the 10. Fan housing guide bar tip touches an object. This causes 11. Chain oil tank the guide bar to be thrown in the direction of the operator. Risk of serious injury or death. 12.

  • Page 4: Safety

    Use and keep the battery charger indoors only. Double insulation. Safety Safety definitions • Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of The definitions below give the level of severity for each electric shock.
  • Page 5 depending on the ways in which the tool is used. occurs, flush with water. If liquid contacts eyes, Operators should identify safety measures to protect additionally seek medical help. Liquid ejected from themselves that are based on an estimation of the battery may cause irritations or burns.
  • Page 6 • Turn to your servicing dealer or Husqvarna if you by taking proper precautions as given below: have questions about the operation of the product. We can give you information about how to operate •...
  • Page 7 • Do not use a product, battery or battery charger that • Do not use the product above shoulder height and is defective. try not to cut with the guide bar tip. • Do not use the product if you are tired or while under the influence of alcohol, drugs or medicine.
  • Page 8 Personal protective equipment Safety devices on the product WARNING: Read the warning instructions WARNING: Read the warning instructions that follow before you use the product. that follow before you use the product. • Do not use a product with damaged safety components.
  • Page 9 Chain brake and front hand guard nearer you the chain brake engages manually by your left hand. Your product has a chain brake that stops the saw chain if you get a kickback. The chain brake decreases the risk of accidents, but only you can prevent them. WARNING: Do not engage in situations where there is a risk of kickback.
  • Page 10 Battery safety WARNING: Read the warning instructions that follow before you use the product. • Only use the Husqvarna BLi batteries that we recommend for your product. The batteries are software encrypted. • Use the Husqvarna BLi batteries that are...
  • Page 11 • Do not use other battery chargers than the one supplied for your product. Only use Husqvarna QC • Only use original spare parts. chargers when you charge Husqvarna replacement Safety instructions for the cutting equipment batteries BLi.

  • Page 12: Assembly

    • Keep the correct depth gauge setting! Follow our • Do maintenance on the cutting equipment regularly instructions and use the recommended depth gauge and keep it correctly lubricated. The risk of wear on clearance. Too large a clearance increases the risk the guide bar, saw chain and drive sprocket of kickback.

  • Page 13: Operation

    3. Put the guide bar on top of the bar bolt. Steer the 6. Make sure that the drive links of the saw chain fit guide bar to its most rear position. Lift the saw chain correctly on the drive sprocket. above the drive sprocket and engage it in the groove 7.
  • Page 14 Chain oil 2. Put the plug in a grounded socket outlet. The LED on the battery charger flashes green one time. All Husqvarna chainsaws have an automatic chain lubrication system. On some models the oil flow is also adjustable. Think about the following when you select a chain oil: Note: The battery will not charge if the battery temperature is more than 50 °C/122 °F.
  • Page 15 4. When all LEDs on the battery come on, the battery is fully charged. 5. Press and hold the start button until the green LED 5. To disconnect the battery charger from the mains light comes on. socket, pull the plug. Do not pull the cable. 6.
  • Page 16 To stop the product better control of the product and the position of the kickback zone. 1. Press and hold the start/stop button on the keypad until the green LED light comes off. • To cut on the push stroke is when you cut with the 2.
  • Page 17 that you understand the causes of kickback front hand guard. You must also hold the handles of and that you can prevent them with correct the product stable with two hands during work. If a working technique. If you are prepared you kickback occurs, your hand may not let go of the decrease the risk.
  • Page 18 To use the product in the tree the operator's harness as a primary safety procedure. If you use the strop as a primary safety procedure, lower the product fully down WARNING: Most accidents occur if the the safety rope. Do not let go of the product from operator does not have full control of the height.

  • Page 19: Maintenance

    3. Lift the branch and remove the product from the cut 4. Use a handsaw or a second chainsaw to release the at the same time. Use a lever to open up the cut. product if necessary. Cut the branch at a minimum of 30 cm/12 in from the trapped product.
  • Page 20 2. Press down the power trigger lockout and make sure 3. Make sure that the product stops when you press that it goes back to its initial position when you and hold the button. The green LED will go off. release it.
  • Page 21 Replace a worn or damaged guide bar or saw chain with the guide bar and saw chain combinations recommended by Husqvarna. This is important in order to keep the safety functions of the cutting equipment. Accessories on page 29 , for a list of replacement bar and chain combinations that we recommend.
  • Page 22 We recommend that you use will be no wood chips but sawdust. Husqvarna file gauge. This will help you to keep A sharp saw chain eats through the wood and the wood maximum cutting performance and the kickback risk at a chips becomes long and thick.
  • Page 23 1. Use a flat file and a depth gauge tool to adjust the depth gauge setting. Only use Husqvarna depth 6. Make sure that the all cutting teeth become the gauge tool to receive the correct depth gauge setting same length when you remove filing material.
  • Page 24 7. Do a check of the chain tension regularly to keep Note: A new saw chain has a running-in period during good cutting performance and a long life. which you must do a check of the tension more frequently. Note: The position of the chain tensioning screw is not Product overview on page the same on all models.
  • Page 25 c) Make sure that the bar tip sprocket turns freely 3. Compare the saw chain with a new saw chain to and that the lubricating hole in the guide bar tip examine if the rivets and links are worn. Replace the sprocket is not blocked.

  • Page 26: Troubleshooting

    Maintenance Before Weekly Monthly Clean the external parts of the product. Make sure that the power trigger and the power trigger lockout function correctly from a safety point of view. Clean the chain brake and make sure that it operates safely. Make sure that the chain catcher is not damaged.

  • Page 27: Transportation, Storage And Disposal

    LED display Possible faults Possible action Warning indicator flashing. Chain brake engaged. Pull back the front hand guard to re- lease the chain brake. Temperature deviation. Allow the product to cool down. Overload. Cutting attachment jam- The cutting attachment is jammed. med.

  • Page 28: Technical Data

    • Keep the battery away from the battery charger during storage. Do not let children and other not Technical data Technical data T536LiXP Motor Type BLDC (brushless) 36V Features Low energy mode savE Lubrication system...

  • Page 29: Accessories

    The part numbers are given in the table below. Using Husqvarna file gauge will give you the correct If you do not know which saw chain you have on your filing angles. We recommend you to always use a product, turn to your servicing dealer.
  • Page 30 11/64 in/4,5 0.025 in/ 90° 30° 0° 5056981-03 5795588-01 0,65 mm Approved batteries for the product Battery BLi110 BLi150 Type Lithium-ion Lithium-ion Battery capacity, Ah Nominal voltage, V Weight, kg/lb 1,2/2.6 1,3/2.9 Battery runtime, min, with SavE acti- vated (free run). Approved battery chargers for the product Battery charger QC120...

  • Page 31: Ec Declaration Of Conformity

    EC Declaration of Conformity EC Declaration of conformity Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declares under sole responsibility that the cordless battery chainsaw Husqvarna T536LiXP from 2016’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), are in conformity with the requirements of the COUNCIL’S DIRECTIVES:...
  • Page 32 Original instructions 1159978-26 2018-03-01...

Table of Contents