Table of Contents
Advertisement
To Avoid the Hazards of Electrical Shock and Fire
•
Do not handle the AC power cord with wet hands.
•
Do not pull on the AC power cord when disconnecting
it from an AC outlet. Grasp it by the plug.
•
Do not put your fingers or objects into the unit.
Location and Handling
•
Do not install the unit in direct sunlight, near strong
magnetic fields, or in a place subject to dust or strong
vibration.
•
Avoid a place with drastic temperature changes.
•
Install the unit in a horizontal and stable position. Do
not place anything directly on top or bottom of the
unit. Depending on your external devices, noise or
disturbance in the picture and/or sound may be
generated if the unit is placed too close to them. In this
case, please ensure enough space between the external
devices and the unit.
•
Depending on the environment, the temperature of this
unit may increase slightly. This is not a malfunction.
•
Be sure to remove the disc and unplug the AC power
cord from the outlet before carrying the unit.
Dew Condensation Warning
•
Dew condensation may form inside the unit in the
following conditions. If so, do not use this unit at least
for a few hours until its inside gets dry.
- The unit is moved from a cold place to a warm place.
- Under conditions of high humidity.
- After heating a cold room.
Notice for Progressive Scan Output
•
Consumers should note that not all high definition
television sets are fully compatible with this product
and may cause artifacts to be displayed in the picture. In
case of picture problems with 525(480) progressive
scan output, it is recommended that the user switch the
connection to the 'standard definition' output. If there
are questions regarding your TV set compatibility with
this 525p(480p) Blu-ray Disc™/DVD player, please
contact our customer service center.
1.2. Maintenance
Servicing
•
Please refer to relevant topics on
"TROUBLESHOOTING" on page 52 before returning
the product.
•
If you need to call a customer service representative,
please know the model number and serial number of
your product before you call. This information is
displayed on the back of the product. Also, please take
a moment to identify the problem you are having, and
be prepared to explain this to the representative. If you
believe the representative will need to help you with
operations, please stay near the product. Our
representatives will be happy to assist you. For online
reference, please visit our website at
www.philips.com/support
EN - 4
Cleaning the Cabinet
•
Wipe the front panel and other exterior surfaces of the
unit with a soft cloth.
•
Never use a solvent, thinner, benzene or alcohol to
clean the unit. Do not spray insecticide liquid near the
unit. Such chemicals may discolor the surface or
damage the unit.
Cleaning Discs
•
When a disc becomes dirty, clean it with a cleaning
cloth. Wipe the disc from the center to outside. Do not
wipe in a circular motion.
•
Do not use solvents such as benzine, thinner,
commercially available cleaners, detergent, abrasive
cleaning agents or antistatic spray intended for analog
records.
Cleaning the Disc Lens
•
If this unit still does not perform properly although you
refer to the relevant sections and to
"TROUBLESHOOTING" in this user manual, the laser
optical pickup unit may be dirty. Consult your dealer or
an Authorized Service Center for inspection and
cleaning of the laser optical pickup unit.
Disc Handling
•
Handle the discs so that fingerprints and dust do not
adhere to the surfaces of the discs.
•
Always store the disc in its protective case when it is
not used.
•
Note that discs with special shapes (heart-shaped discs,
octagonal discs, etc.) cannot be played back on this unit.
Do not attempt to play such discs, as they may damage
the unit.
Testing the Remote Control
•
If the remote control is not working properly, you can
use a digital camera (including a cellular phone with
built-in camera) to see if it is sending out an infrared
signal.
How to perform the test?
1. Point the IR transmitter of the remote
control towards the lens of the digital
camera (or cell phone camera).
2. Turn on the digital camera and look at
the IR transmitter of the remote
control through the LCD display of
the digital camera.
3. While looking at the LCD, press the
buttons on your remote control you
want to test.
a. If your remote control is working
properly, the IR transmitter of the
remote control will create a noticeable
flash on the LCD of the digital camera.
b. If it does not flash, replace the
batteries in your remote with new
batteries and try again. If it still does
not flash, your remote control may
be damaged or defective. Please
contact customer service for
replacement options.
Advertisement
Table of Contents
