Advertisement

Quick Links

ELKO - Smart Smoke Alarm Battery
Device user guide
Information about features and functionality of the devices
11/2022
www.elko.no

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Smart Smoke Alarm Battery and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Elko Smart Smoke Alarm Battery

  • Page 1 ELKO - Smart Smoke Alarm Battery Device user guide Information about features and functionality of the devices 11/2022 www.elko.no...
  • Page 2 Legal Information The ELKO brand and any trademarks of ELKO AS and its subsidiaries referred to in this guide are the property of ELKO AS or its subsidiaries. All other brands may be trademarks of their respective owners. This guide and its content are protected under applicable copyright laws and furnished for informational use only.
  • Page 3: Table Of Contents

    Table of Contents Safety information ..................4 ELKO - Smart Smoke Alarm Battery ............5 For your safety ...................5 About the device..................5 Installing the device ..................7 Pairing the device ..................7 Pairing device manually.................7 Pairing device with auto scan..............9 Setting up connection without ELKO system ..........9 Interconnecting devices without ELKO SmartHUB........9...
  • Page 4: Safety Information

    Safety information Safety information Important information Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service, or maintain it. The following special messages may appear throughout this manual or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.
  • Page 5: Elko - Smart Smoke Alarm Battery

    About the device The Smart Smoke Alarm Battery (device) uses a photoelectric sensor to detect smoke generated by fire. It also includes a temperature sensor that detects heat caused by rapid increase in temperature. When connected to the ELKO system the device sends the notifications via the ELKO app.
  • Page 6 ELKO - Smart Smoke Alarm Battery Operating elements A. Status LED (Amber, Green and Red LED) B. Standby LED (Red LED) C. Test/Hush button D. Power switch E. Setup/Reset button DO NOT PAINT OFF/AUTO OFF/AUTO PUSH TO TEST / HUSH Installation location •...
  • Page 7: Installing The Device

    Refer to the installation instruction supplied with this product. See Smart Smoke Alarm Battery. Pairing the device Using the ELKO app, pair your device with the ELKO SmartHUB to access and control the device. You can either add the device manually or do an auto-scan to pair it.
  • Page 8 ELKO - Smart Smoke Alarm Battery 5. To pair the device with an install code,, tap Add Device with Install Code to display the slide-up menu. Select any one of the options (B): – Scan Install Code - You can scan the device for the an install code.
  • Page 9: Pairing Device With Auto Scan

    3. Tap Auto scan and than tap Confirm. 4. If you have multiple hubs, do Step 4 or proceed to Step 5. 5. Tap Select hub and select an ELKO SmartHUB from the slide-up menu. 6. Press the Set/Reset button 3 times within 2 s.
  • Page 10: Disconnecting A Slave Device

    ELKO - Smart Smoke Alarm Battery 2. Short press the Test/Hush button 3 times within 2 s on the primary device. The Standby LED turns on for 30 s once it is in pairing mode. 3. Identify a Slave device and short press the Test/Hush button 3 times within 2 The Standby LED blinks 3 times on both Master and devices indicating a successful RF connection.
  • Page 11: Testing The Device

    It is recommended to test the device once a month. If the device is installed in a mobile home, it is recommended to test the device weekly and before every journey. NOTE: Using ELKO Smart app you can set the monthly reminder for test alarm in settings, page...
  • Page 12: Testing The Interconnected Device(S)

    Configuring the device Changing the device icon You can change the device icon using the ELKO Smart app. 1. On the Home page, select the device for which you wish to change the icon. 2. At the top-right corner of the screen, tap 3.
  • Page 13: Renaming The Device

    Name Save Changing the device location You can change the device location using the ELKO Smart app. 1. On the Home page, select the device for which you wish to change the location. 2. At the top-right corner of the screen, tap 3.
  • Page 14: Removing The Device From The App

    ELKO - Smart Smoke Alarm Battery Removing the device from the app You can remove a device from the device list using the ELKO Smart app, To remove the device: 1. On the Home page, tap All devices > Smoke Alarm.
  • Page 15: Using The Device

    No Alarm History Settings Checking the device history Using the ELKO Smart app, you can monitor the smoke detection by accessing the device history. To see the device history: 1. On the Home page, tap All devices > Smoke Alarm.
  • Page 16: Setting Led Brightness

    ELKO - Smart Smoke Alarm Battery Setting LED brightness You can change the LED brightness level between minimum and maximum manually or by using ELKO app. Changing the LED brightness manually 1. When the device is in standby mode, short press the test/hush button 3 times within 2 s.
  • Page 17: Test Alarm Reminder

    ELKO - Smart Smoke Alarm Battery Test alarm reminder You can set the reminder for test alarm in the ELKO app. 1. On the Home page, tap All devices > Smoke Alarm. 2. On the device control panel page, tap Settings.
  • Page 18: Silencing The Device

    NOTE: Wait for 10 minutes before performing any test to avoid malfunctioning of the device. Once the device is set to Hush Mode the status can be checked in ELKO app. Smoke Alarm The device is in Hush Mode - it will not detect smoke temporarily.
  • Page 19: Snoozing The Device Alerts

    ELKO - Smart Smoke Alarm Battery Temporarily disabling smoke detection To temporarily disable the smoke detection of a device, short press the Test/Hush button once when the device is in Standby mode. The device will not detect smoke for 10 minutes. During this mode the Standby LED blinks once every 8 s.
  • Page 20: Creating An Automation

    ELKO - Smart Smoke Alarm Battery Creating an automation Automation allows you to group multiple actions that are usually done together, triggered automatically or at scheduled times. Using the ELKO Smart app, you can create automations based on your needs. To create an automation: 1.
  • Page 21 ELKO - Smart Smoke Alarm Battery 6. In the Add Condition menu, you can do either or all of the following options (C): – When weather changes - Select the various weather settings – Schedule - Set the time and day –...
  • Page 22 ELKO - Smart Smoke Alarm Battery 9. In the Add task menu, you can do either or all of the following options (F): – Run the device- Select the devices that you want to triggered. – Moment or Automation- Select the moment which you want to trigger or select the automation that you want to enable or disable.
  • Page 23 ELKO - Smart Smoke Alarm Battery Example of an automation This demonstration shows you how to create an automation to get notification on your app when the smoke is detected. 1. Go to Automation > + to create an automation.
  • Page 24 ELKO - Smart Smoke Alarm Battery 7. In the Automation Settings page, tap Save. Automation settings Cancel Save My Automation Any condition is met (1/10) Smoke Alarm Smoke Alarm: Smoke Alarm Action (1/80) All-Day Once the automation is saved, it is visible on the Automation tab. You can tap the toggle switch on the automation to enable it.
  • Page 25: Maintenance And Cleaning

    ELKO - Smart Smoke Alarm Battery Maintenance and cleaning A monthly inspection is recommended to help ensure the device is dust, dirt, and insect free. The device can be vacuumed (strongly recommended) or brushed with a soft brush to remove accumulated dust, dirt or kitchen grease. Apply a small amount of insect surface spray to a cloth and wipe around device(s) every 3 to 6 months to mitigate insect ingress..
  • Page 26: Led Indications

    ELKO - Smart Smoke Alarm Battery LED Indications Pairing User Action LED Indication Status Press the Setup/Reset button 3 times LED blinks yellow yellow, once per second. Pairing mode is active for 30 seconds. When pairing is completed, LED glows green for some time before turning Off.
  • Page 27: Troubleshooting

    ELKO - Smart Smoke Alarm Battery Troubleshooting Issue Resolution/Action Device does not sound when tested 1. Confirm that the power switch is in ON position, or the device is installed correctly. If you are unsure then remove and reinstall the device.
  • Page 28 Trademarks This guide makes reference to system and brand names that are trademarks of their relevant owners. • Zigbee ® is a registered trademark of the Connectivity Standards Alliance. • Apple ® and App Store ® are brand names or registered trademarks of Apple Inc. •...
  • Page 30 ELKO AS Sandstuveien 68, 0680 Oslo Pb 6598 Etterstad, 0607 Oslo Norway +47 67 79 39 00 support@elko.no www.elko.no As standards, specifications, and design change from time to time, please ask for confirmation of the information given in this publication.

This manual is also suitable for:

Eko09761

Table of Contents