Advertisement
4 Function buttons
The function changes according to the USE MODE.
USE M ODE 1: Press to select the source of the
receiver.
USE M ODE 2: Press to select the source you w ant
to output from the 2ND AV jacks.
Press one of the buttons to select the component you
want to use. When you press any of the function
buttons, the receiver turns on. The components are
factory assigned to the buttons as follows. When you
want to assign other components, program the remote
following the steps in "To change the button
assignments".
Button
VIDEO1
VIDEO2
VIDEO3
DVD/LD
TV/SAT
TAPE
MD/DAT
CD
TUNER
5.1 CH
PHONO
SOURCE
1)
The setting cannot be changed.
2)
USE MODE 1 only.
3)
USE MODE 2 only.
5 Operation buttons* *
The following table describes the function of the
buttons.
Button(s)
N
n
X
x
./>
m/M
6 CH/ PRESET/ D.SKIP/ +/ – buttons* *
Press repeatedly to select a preset station or channel.
When using a multi-disc changer, press to skip a disc.
7 SHIFT button
When the tuner is selected, press repeatedly to select a
memory page for presetting radio stations or tuning to
preset stations.
Downloaded from:
https://www.usersmanualguide.com/
Assigned component
VCR (VTR mode 3)
VCR (VTR mode 1)
VCR (VTR mode 2)
DVD player
TV tuner
Tape deck B
MD deck
CD player
1)
Built-in tuner
2)
DVD player
1) 2)
Turntable
3)
—
Function
Starts play. (Starts play on the front side of
the cassette.)
Starts play on the reverse side of the cassette.
Pauses play or recording, and starts
recording when the component is in
recording standby.
Stops play.
Skips tracks.
Fast forwards or rewinds.
8 USE M ODE button
Press to change the codes of the function buttons (4)
(changing the source of the receiver or switching
sources to output from the 2ND AV jacks) or to change
the category of the function buttons.
9 USE M ODE indicator
When setting the remote using the USE MODE button,
or whenever a button on the remote is pressed while
the remote is in the USE MODE 2, the indicator lights.
** The function of these buttons switches automatically each time
you press the function buttons (4). The above explanation is
intended to serve as an example only. Therefore, depending on
the component, the above operation may not be possible or
may operate differently than described.
z
Clearing all programmed signals
Press ?/1 and USE MODE at the same time. The remote is reset
to its factory-setting.
To sw it ch t he USE M ODE of t he rem ot e
To use RM-US104 in the 2nd room, it is necessary to
switch the USE MODE. To use as a simplified remote, it is
not necessary to switch the USE MODE.
x When using as a sim plif ied rem ot e
Always set to USE MODE 1.
x When using in t he 2nd room
You can adjust the volume.
To switch output from the 2ND AV jacks in the main
room
Switch to USE MODE 2.
When controlling Sony receivers in the 2nd room
Switch to USE MODE 1. You can switch sources on the
receiver.
Indicator
USE MODE
VIDEO 1 VIDEO 2
DVD/LD
TV/SAT
MD/DAT
CD
PHONO SOURCE
5.1CH
Press USE M ODE.
This remote's USE MODE switches and the indicator
flashes as follows:
USE MODE 1 t 2 : The indicator flashes twice.
USE MODE 2 t 1 : The indicator flashes once.
z To check the current USE M ODE, press any button
Under USE MODE 2, the indicator lights while a button is
pressed. Under USE MODE 1, the indicator does not light while a
button is pressed.
?/1
USE M ODE
VIDEO 3
TAPE
TUNER
Advertisement
