Philips 20PHH4109/88 Service Manual page 35

Picture mode Screen size
Cool (11000K) 20PHH4109/88 72
20PHH4109/60 84
22PFH4109/88 68
22PFK4109/12
22PFT4109/12
24PHH4109/88 76
24PHH4109/60 93
24PHK4109/12 77
24PHT4109/12 68
32PHH4109/88 107
32PFH4109/88 112
32PFT4109/12
32PHT4109/12 112
32PHH4109/60 120
40PFH4109/88 73
40PFT4109/12
47PFH4109/88 73
47PFT4109/12
Warm (6500K) 20PHH4109/88 102
20PHH4109/60 116
22PFH4109/88 124
22PFK4109/12
22PFT4109/12
24PHH4109/88 103
24PHH4109/60 121
24PHK4109/12 117
24PHT4109/12 124
32PHH4109/88 128
32PFH4109/88 123
32PFT4109/12
32PHT4109/12 125
32PHH4109/60 123
40PFH4109/88 127
40PFT4109/12
47PFH4109/88 127
47PFT4109/12
This group setting of colour temperature will be applied
automatically to the TV / VGA / HDMI / AV sources.
6.4 Option Settings
6.4.1 Introduction
The microprocessor communicates with a large number of I
ICs in the set. To ensure good communication and to make
digital diagnosis possible, the microprocessor has to know
which ICs to address. The presence / absence of these
NT72567 ICs is made known by the option codes.
Notes:
• After changing the option(s), save them by pressing the OK
button on the RC before the cursor is moved to the left,
select STORE and press OK on the RC.
• The new option setting is only active after the TV is
switched "off" / "stand-by" and "on" again with the mains
switch (the NVM is then read again).
6.4.2 Option Code Overview
Enter SAM mode to check the option codes. they could not be
edited in the NVM.
6.4.3 Display Code Overview
Press the following key sequence on a standard RC
transmitter: "062598" directly followed by MENU and "xxx",
where "xxx" is a 3 digit decimal value of the panel type: see
column "Display Code" in
Code, restart the set immediately.
Colour temperature
Red Green Blue
96 128
73 128
76 128
97 68 124
65 94 128
68 126
75 123
96 121
76 128
103 128
107 128
103 112 128
106 128
127 128
89 128
96 74 128
89 128
96 120 121
117 128
121 128
120 128
96 87 127
101 120 123
94 121
126 128
123 128
120 128
111 81
121 96
120 113 86
120 121
96 128
121 120
87 96 128
121 120
126 120 128
Table 6-3. After resetting the Display
Alignments
Table 6-3 Display code overview
CTN_ALT BOM#
20PHH4109/88
20PHH4109/60
22PFH4109/88
22PFK4109/12
22PFT4109/12
24PHH4109/88
24PHH4109/88
24PHH4109/60
24PHH4109/60
24PHK4109/12
24PHK4109/12
24PHT4109/12
24PHT4109/12
32PHH4109/88
32PFH4109/88
32PFT4109/12
32PHH4109/60
32PHT4109/12
40PFH4109/88
40PFT4109/12
47PFH4109/88
47PFT4109/12
6.5 Reset of Repaired SSB
A very important issue towards a repaired SSB from a Service
repair shop (SSB repair on component level) implies the reset
of the NVM on the SSB.
A repaired SSB in Service should get the service Set type
"00PF0000000000" and Production code "00000000000000".
Also the virgin bit is to be set. To set all this, you can use the
ComPair tool or use the "NVM editor" and "Dealer options"
items in SAM (do not forget to "store").
After a repaired SSB has been mounted in the set (set repair
on board level), the type number (CTN) and production code of
the TV has to be set according to the type plate of the set. For
this, you can use the NVM editor in SAM. The loading of the
CTN and production code can also be done via ComPair
(Model number programming).
2
C
In case of a display replacement, reset the "Operation hours
display" to "0", or to the operation hours of the replacement
display.
Remark:
- After the NVM has been replaced, go to SAM and scroll to the
<Reload MAC address> (see figure 1*).
- Select the item and press <OK> on the RC.
6.5.1 Reset of Repaired SSB
Instruction
After NVM replacement, reload MAC address via SAM
menu.This ensures the correct MAC address to be available in
CSM for future repair actions.
Way of working:
• After the NVM has been replaced, go to SAM and scroll to
the <Reload MAC address> .
• Select the item and press <OK> on the RC.
Notes:
• Only applicable to all related models that are "Smart TV
level 0"enabled (only YouTube access). For models
without internet connection feature, no action is needed.
• HDCP keys are located in the NVM. If you are loading NVM
with the ComPair tool, there is warning message displayed.
back to
div. table
TPN14.1E LA 6.
Panel Type
TPM195WD1-RTN01
TPM195WD1-RTN01
TPM215HW01-HGJL02
TPM215HW01-HGJL02
TPM215HW01-HGJL02
TPM236H3-BJ1L02
TPM236H3-BJ1L03
TPM236H3-BJ1L02
TPM236H3-BJ1L03
TPM236H3-BJ1L02
TPM236H3-BJ1L03
TPM236H3-BJ1L02
TPM236H3-BJ1L03
TPT315B5-DXJSFE
TPT315B-EUJFFA
TPT315B-EUJFFA
TPT315B5-DXJSFE
TPT315B5-DXJSFE
TPT400LA-HM06
TPT400LA-HM06
TPT470H1-DUJFFE
TPT470H1-DUJFFE
EN 35
Display Code
017
017
018
018
018
019
030
019
030
019
030
019
030
006
007
007
006
006
009
009
011
011
2014-Feb-21