Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Telic SBC3 CAN 4G
Summary of Contents for Telic SBC3 CAN 4G
- Page 1 SBC3 CAN 4G User Manual 04.12.2019...
-
Page 2: Table Of Contents
Technical features ..............................7 Functional Overview ..............................8 Wiring description ..............................9 Wiring the SBC3 CAN 4G to the asset or vehicle ..................13 Delivery Content and Accessories ........................13 4 Operating Set up ..................... 14 Operating the device............................. 14 Insert the SIM Card .............................. -
Page 3: General Terms And Conditions
The copyright of the related documentation is with Telic AG. The Telic Logo and the terms Telic, and Telic SBC3 CAN 4G are brands of Telic AG. All further names and terms used can be brands or registered brands of their respective owners. -
Page 4: Conventions Used In This Manual
The following safety instructions must be followed in order to ensure the safety of users and the device. If these instructions are ignored, Telic will not assume responsibility for any damages that are incurred. Pg 3... -
Page 5: Audience And Intended Use
Negative consequences on safety and device integrity due to connecting the wrong cable to the unit. Only use cables which are listed in the Telic accessory list. NOTICE The messages of the device are transmitted via the mobile network. Therefore you need a standard 3 Volts or 1.8 Volts SIM card. -
Page 6: Esd Protection
Take proper measures for ESD protection, e.g., electrical connection of the body to ground. Repair of ESD damages caused by user’s negligence will not be covered by Telic’s warranty. General Battery Handling The device includes a rechargeable battery. The battery is designed to represent the highest possible degree of safety. -
Page 7: Battery Storage
The batteries included with the devices must only be used in the device. The batteries must never be used in any other device unless specifically authorized by Telic, including but not limited to other Telic products or devices. -
Page 8: Identification (Label To Be Modified)
SBC3 CAN 4G User Manual - Telic AG Identification (label to be modified) On the top side of the device, you will find the type label. Description Label Serial number Serial number International Mobile IMEI Equipment Identity Hardware Revision HW-Rev. -
Page 9: Functional Overview
Weight: 220 g (*) The SBC3 CAN 4G begins to operate immediately after receiving main power, even after long non- operating times, and depleted back-up battery. Functional Overview The picture below gives an overview about the main components and its functions available on the PCB after opening the upper lid. -
Page 10: Wiring Description
SBC3 CAN 4G User Manual - Telic AG Picture 1: Functional Overview Function Connectors for power supply and vehicle interfaces ON/OFF button Status LEDs (GNSS, Mobile service, Power) Mobile antenna SIM card holder GNSS antenna Connector for rechargeable battery Table 2: Device components... - Page 11 DIG_IN1 1-wire VCC/DIG_IN3 Debug RX Debug TX CAN L CAN H Picture 2: SBC3 CAN 4G Cable Pins allocation Description Signal Ground VCC /DIG IN_3 External power supply 7 – 32V DC (optional digital input) DIG_IN1 Digital input 0 – 32V DC DIG_IN2 Digital input 0 –...
- Page 12 V24 level -12V … +12V 1-wire interface for external 1-wire devices 3,3V DC Debug RX serial interface for Telic-Traces V24 level -12V … +12V Debug TX serial interface for Telic-Traces V24 level -12V … +12V Table 4: 6 pin Connector in the middle...
- Page 13 The voltages on inputs and outputs must be identical 120 Ohm Termination Resistor 120 Ohm Termination Resistor (if SBC3 CAN 4G is the last device on the bus) (if vehicle has no internal termination) CAN Bus CAN H CAN L...
-
Page 14: Wiring The Sbc3 Can 4G To The Asset Or Vehicle
2A fuses. We recommend the use of blade type fuses, as they are used in the automotive sector. Delivery Content and Accessories In addition to the SBC3 CAN 4G, the following accessories can be part of the shipment, if previously ordered. Accessory Name... -
Page 15: Operating Set Up
Please take proper ESD protection measures (e.g. electrical connection of the body to ground) to make sure you don’t destroy internal electronics! Repair of ESD damages caused by user’s negligence will not be covered by Telic’s warranty. Electrostatic discharge (ESD) is the sudden and momentary electric current that flows between two objects at different electrical potentials normally caused by static electricity. -
Page 16: Insert The Sim Card
To speed up the log-in process into the mobile network, the SIM card should contain no or only a few phone book entries. The messages of the SBC3 CAN 4G are transmitted via the mobile network. Therefore you need a standard 3 Volts or 1.8 Volts SIM card. -
Page 17: Switching The Device On/Off
NOTICE Telic delivers the devices switched-OFF If the Telic SBC3 CAN 4G unit is switched off, you can switch it on by a single short press of the white button (see Picture 10: Switching the device On/Off). If you want to switch the device off, then double press shortly the white button. It is possible to reset the device (complete power off of the controller) with a single long press of at least 5 seconds. - Page 18 Picture 10: Switching the device On/Off Closing the device Please close the SBC3 CAN 4G housing by screwing the 4 screws down back into its original position. The clear plastic light guides must be located above the LEDs. Please ensure that the cover locks properly into position.
-
Page 19: Status Indicators
SBC3 CAN 4G User Manual - Telic AG 5 Status indicators Left indicator: Power status Middle Indicator: Mobile status Right Indicator: GNSS status This LED blinks green and The left indicator consists of two The yellow LED reflects the mobile indicates the status of the GNSS LEDs: one green and one red. -
Page 20: Connect To The Vehicle
Please connect the Telic SBC3 CAN 4G with the vehicle according to the following instructions using the connection cable. Please do not connect the connector to the Telic SBC3 CAN 4G before all wires you intend to use are connected to the vehicle. The power supply has to be available while the ignition is off. -
Page 21: Configuring A Device
User Manual - Telic AG If the Telic SBC3 CAN 4G is configured to use a motion dependent power mode, the device can detect and report that it is moving (e.g. if it is stolen or being transported via a second vehicle) even while ignition is off. -
Page 22: Basic Configuration
SBC3 CAN 4G User Manual - Telic AG low power mode. An input can be configured to wake up and stay awake until the input goes to low again. Motion Sleep Mode If the motion sensor detects stationary, the device will switch off GNSS and mobile service modules, and µC is switched to low power mode. - Page 23 SBC3 CAN 4G User Manual - Telic AG This means that a position message is generated and transmitted every 2 km on a freeway or highway (driving with about 120km/h). As soon as motion is ended (detected by built-in sensor), the device will go to sleep mode. When going back to motion (detected by the sensor), the device will automatically resume tracking.
- Page 24 30 deg. As soon as the Ignition signal is detected as off, the SBC3 CAN 4G will enter the sleep mode. This profile should be used for all kind of tracking applications where a high accurate position track is needed.
-
Page 25: Connection To Kentaur
00b495877378.137.103.86,1561,internet.wind,,,1,80,60,,,,,0 8 Connection to Kentaur Kentaur is Telic’s Application Enabling Platform able to interpret messages sent by our telematics devices, and present them in an user friendly way thanks to its graphical interface. The device can be managed through Kentaur once it is connected to the platform. -
Page 26: Dashboard Guide
SBC3 CAN 4G User Manual - Telic AG Dashboard Guide This application gives you the possibility to manage the devices that are connected via the Kentaur IoT platform. Register/Login Get to the Kentaur Website: https://kentaur.cc (works only via Google Chrome) ... - Page 27 SBC3 CAN 4G User Manual - Telic AG The following window will pop up Choose a name for your dashboard Add the widgets you want to see on your dashboard by clicking the “Add” button. At the “Device info” widget you first have to choose which parameter of the device info shall...
- Page 28 SBC3 CAN 4G User Manual - Telic AG After selecting your widgets please press "Save". Otherwise press "Close", by which you do not save your changes and return to the Dashboard page. As Admin you can choose in the widgets, if you want to see "all devices" (all devices on this domain) or "my devices"...
- Page 29 SBC3 CAN 4G User Manual - Telic AG In the second menu line (shown in the picture above), you can choose the dashboard template, lock and unlock the dashboard. On the right side widgets can be added (the sign is shown in orange if the dashboard is unlocked; if it is shown in grey, widgets cannot be added as dashboard is locked).
- Page 30 SBC3 CAN 4G User Manual - Telic AG Devices After you have switched to the menu devices, all devices (if already present) are shown in a tabular format. In the table the device can be sorted in every column by alphabetical order. The sorting is shown by a small arrow next to the column´s headline.
- Page 31 SBC3 CAN 4G User Manual - Telic AG Here you can check the details of the device, check the content of the last message or inspect data across multiple data ranges. With this data inspection, routes can be viewed in a map view or messages picked for further inspection.
- Page 32 SBC3 CAN 4G User Manual - Telic AG The dataset can be exported as CSV (Comma Separated Value) into third party applications, like MS Excel. With the last button in the menu (“Chart”) specific data points like battery level, distance, altitude or speed can be viewed in a graphical overview.
- Page 33 SBC3 CAN 4G User Manual - Telic AG All devices will be delivered with a factory provided configuration, but, as shown in the screenshot above, you can select one of the pre-defined configuration profiles. You have to click into the field “Conf. profiles”.
- Page 34 SBC3 CAN 4G User Manual - Telic AG Explanation of the configuration profiles The following options are available: Timer based sleep mode Message once per hour Container / Asset tracking – Position messages are generated each time the device starts and Endurance track stops moving.
- Page 35 SBC3 CAN 4G User Manual - Telic AG By selecting the Plus-button, additional users can be added. A pop up window with the required and optional information fields appear. There are three levels of users (“Role”): Administrator, short: Admin ...
- Page 36 SBC3 CAN 4G User Manual - Telic AG User An user can add devices and other users. He can view, change and delete only devices that are assigned directly to him. User accounts are permanent, however we do recommend to set a specific expiry date.
-
Page 37: Troubleshooting Hints
The device doesn’t log into the mobile network Troubleshooting Possible issue source The Telic SBC3 CAN 4G isn’t in a mobile Please check whether there is mobile reception in this covered area. area (e.g. using a cell phone) and move if needed to another area. - Page 38 In order to see and capture traces, a serial terminal program for debugging (such as Realterm) will have to be run by the computer. This SW tool will create a traces file that can be forwarded to Telic’s support team for an in-depth analysis.
Need help?
Do you have a question about the SBC3 CAN 4G and is the answer not in the manual?
Questions and answers