Santa's best CCT15 - Pre-Lit & Pre-Shaped Christmas Tree Manual
  1. Manuals
  2. Brands
  3. Santa's best Manuals
  4. Artificial Pine Trees
  5. CCT15
  6. User manual

Santa's best CCT15 - Pre-Lit & Pre-Shaped Christmas Tree Manual

Advertisement

Table of Contents
Contents
Santa's best CCT15 - Pre-Lit & Pre-Shaped Christmas Tree Manual

INTRODUCTION

With proper use and care, this tree will provide years of trouble-free enjoyment.
Please follow the instructions below in order to effectively assemble and disassemble your tree.
In the event that you should encounter any issues during the assembly of your tree; please refer to the "Troubleshooting" portion of this manual or call our toll free customer service number at 1-888-831-6656, and a trained representative will assist you.

ASSEMBLY INSTRUCTIONS

(We recommend wearing proper clothing in order to prevent scratches that may occur during the assembly process.) Carefully unpack the contents from the tree's carton (Fig 1); including the contents of the poly-bag that is adhered to the interior flap of the tree's carton.
Contained in the poly-bag are LED replacement bulbs and a remote control which operates your tree's 7 function lighting capability.
Your tree should include the following components:
A folding metal tree stand with (3) eyebolts.
An ON/OFF push button foot pedal with cord and plug (Fig 6); which is pre-attached at the lowest section of your tree (Fig 5). The 5' tree will have (2) tree sections. The 6.5' and 7.5' trees will have (3) tree sections; ("A", "B" and "C"; as shown in Fig 5). The 9' tree will have (4) tree sections "A", "B", "C" and "D".
ASSEMBLY INSTRUCTIONS

ASSEMBLY OF THE TREE STAND

  1. Remove the tree stand from the plastic bag, loosen the eye bolt and open the tree stand to form an "X".
  2. Align the holes for the insertion of the remaining (2) eyebolts.
  3. Insert each eyebolt and begin threading in a clockwise direction for a couple of rotations only; leaving enough room for the tree's pole from section "A" to be inserted into the assembled stand (Fig 2).
    ASSEMBLY OF THE TREE STAND
  4. Place the tree stand in its desired location; as once the tree is fully assembled, it may be too difficult to move and relocate.

ASSEMBLY OF THE TREE

  1. Locate the bottom section of the tree which is identified by a label on the outer branches marked "A" (Fig 5).
    ASSEMBLY OF THE TREE - Step 1
  2. Remove the protective plastic cap by twisting and pulling it from the end of the pole, (that is pinched to a point), and place the end into the tree stand. Be sure the pointed end of the pole extends to the bottom end of the stand.
  3. Now tighten the eyebolts evenly on the tree stand; being careful not to over-tighten (Fig 3).
    ASSEMBLY OF THE TREE - Step 2
  1. Carefully cut the nylon strapping bounding the branches upright.

    Be extremely careful not to cut any of the exposed light set wires.
  2. Now gently guide the branches downward into place.
  3. Beneath the canopy of section "A", contains an push button foot pedal with cord and plug (Fig 6). Remove the twist-tie binding the cord together and insert the plug into a working electrical outlet.
    ASSEMBLY OF THE TREE - Step 3
  4. On/off push button foot pedal operation: The on/off push button foot pedal is intended to provide basic manual on/off operation only; and therefore cannot provide the remote control's 7 function lighting capability.

EZ-POWER™ TECHNOLOGY

NOTE: Your tree has been designed with EZ-Power™ technology; allowing for each of the tree's remaining sections to light up automatically, upon a firm insertion of each lettered section (Fig 5).

  1. Locate the next section of the tree which is identified by a label on the outer branches marked "B" (Fig 5).
  2. Remove the protective plastic cap by twisting and pulling it from the end of the pole on section "B"; insert that end onto the top of the pole of section "A" (Fig 4).
    EZ-POWER™ TECHNOLOGY
  1. Once section "B" is fully inserted downward into section "A"; both section "A" and section "B" will now be lit.
  2. Again, carefully cut the nylon strapping bounding the branches upright; being extremely careful not to cut any of the exposed light set wires.
  3. Now gently guide the branches of section "B" downward into place.
  4. Depending on the height of the tree you have purchased, you will continue to build your tree upwards, section by section, following the above steps until the tree is completely assembled. Each section of the tree is labeled in alphabetical order beginning from the bottom to the top.

REMOTE CONTROL OPERATION

Contained in the poly-bag; which is adhered to the interior flap of the tree's carton, is your remote control that operates your tree's 7 lighting functions.
Before operation; a standard 9 volt type battery (6F22, 6LR61 or 23F6-220) must be installed into the remote control; by simply removing the slide plate located on the back of the remote control.
The remote controls the following 7 functions as well as the ON/OFF operation. To change the functions, simply press the "Function or "Function " to cycle through each function.
REMOTE CONTROL OPERATION

  • Steady Multi
  • Steady White
  • Steady Pastel
  • Slow Fade White to Multi
  • Flash White to Multi
  • Slow Twinkle
  • Fast Twinkle

NOTE: If the tree is powered off by the use of the push button foot pedal, remote control or by unplugging it from the electrical outlet; when powered back on the tree will resume the memory of the last lighting function selected.

TROUBLESHOOTING

  1. If the tree does not illuminate press the function button on your remote control. If failure to light persists the battery may need to be replaced. Insert a standard 9 volt type battery (6F22, 6LR61 or 23F6-220); aligning the appropriate ( +/- ) markings accordingly.
    NOTE: The tree's 7 function lighting capability is controlled solely by the use of the remote control provided. If the tree fails to light due to a damaged or defective remote control; please resort to manual push button foot pedal operation until a new remote control can be provided through our customer service center.
  1. If failure to light persists, press the push button foot pedal; as it may be in the "Off" mode.
  2. If the top of the tree or another individual lettered section does not illuminate, remove each section and then reinsert as instructed, to ensure the electrical connection is made.
    NOTE: The tree's top is designed specifically for a secure and firm connection point. Downward force will be needed to ensure that the electrical connection occurs.
  3. Always inspect your tree for any burned out LED bulbs. Although the tree will continue to remain lit even if a bulb burns out, is loose or is missing; any burned out LED bulbs should be replaced promptly to ensure the performance and life expectancy of your tree.
  4. If lighting is out of sequence after replacing an LED, remove and re-insert the LED making sure to align the husk tabs as illustrated in the safety instruction sheets. This is a specialty bulb. Do not replace with a standard LED or Incandescent bulb. Should you need additional bulbs please call our customer service department at 1-888-831-6656.
    NOTE: DO NOT USE A DIMMER SWITCH, INSTALL ANY ADDITIONAL LIGHTING OR ORNAMENTION THAT IS POWERED THROUGH THE LIGHT BULB SOCKETS. DOING THIS MAY RESULT IN DAMAGE TO THE LIGHTING SYSTEM OR MAY CAUSE PERSONAL INJURY; THEREFORE VOIDING THE LIMITED WARRANTY PROVIDED WITH THIS PRODUCT.

DISASSEMBLY & STORAGE

  1. Gently remove the plug from its electrical outlet, and carefully bind the cord which contains the push button foot pedal and plug.
  2. Beginning with the tree's top section; lift each section straight up from the section below, and continue working downward.
    NOTE: You may have to slightly wiggle each section as you lift each section upward.
  3. To remove the bottom and final section; loosen the eyebolts by turning in a counter-clockwise direction and lift section "A" from the support collar of the tree stand.
  4. Gently fold the branches of each section upward, towards the center, and position in the storage container.
    NOTE: With the exception of the tree's "top" section; by holding each section upside down; the branches will collapse downward, due to the hinging, aiding in the packing of each section into the storage container.
  5. Fully unthread the eyebolts from the tree's stand and fold together; placing in the storage container.
  6. It is recommended to always store the tree in a cool, dry location protected from excessive exposure to heat or sunlight. NOTE: Store your remote control in a SAFE & DRY location and remove the battery from remote control before storage.
    NOTE: ALTHOUGH THE LED LIGHT STRINGS ON THE TREE ARE RATED FOR INDOOR OR OUTDOOR USE; THE COMBINATION OF THE TREE WITH THE LED LIGHTS IS RECOMMENDED FOR INDOOR USE ONLY.

This is not a toy, for decorative use only.
Riverwoods, IL 60015 USA www.santasbest.com

Customer service hours of operation:
Monday-Friday: 8:00am – 4:30pm CST.
Holiday weekends:
Last weekend in November: 8:00am – 4:30pm CST.
First weekend in December: 8:00am – 4:30pm CST.
Visit us on the web at www.santasbest.com

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Santa's best CCT15 - Pre-Lit & Pre-Shaped Christmas Tree Manual

Advertisement

Need Assistance?

Do you have a question about the CCT15 that isn't answered in the manual? Leave your question here.

Error while submitting your question. Please, reload page and try again.

Thank you! Your question has been received!

Related Manuals for Santa's best CCT15

Save Article as PDF

Table of Contents