Santa's best LED15 - Outdoor Bare Branch Tree Sculpture Manual

INTRODUCTION

Please follow the instructions below in order to effectively assemble and disassemble your outdoor tree.
In the event that you should encounter any issues during the assembly of your tree; please refer to the "Troubleshooting" portion of this manual or call our toll free customer service number at 1-888-831-6656, and a trained representative will assist you.

Customer service hours of operation:
Monday-Friday: 8:00am – 4:30pm CST.
Holiday weekends:
Last weekend in November: 8:00am – 4:30pm CST.
First weekend in December: 8:00am – 4:30pm CST.

Visit us on the web at www.santasbest.com

ASSEMBLY INSTRUCTIONS

No tools required (Hammer optional).
Retain carton for storage.

Carefully remove all parts from the carton. Your tree should include the following (Fig 1):

• 1 collapsible tree base
• 1 trunk with control box and plug 1 top branch tree section 1 Bag containing:
• 1 remote control
• 9 Volt battery
• Replacement RGB/LED bulbs
• Extra branch safety tips
• 4 Lawn stakes
  

ASSEMBLY OF TREE STAND

Open the two sides of the hinged collapsible tree base andplace on level ground in your desired display location (Fig 2).

ASSEMBLY OF THE TREE

1. Insert the tree's trunk into the tree's base (Fig 3).
   
2. Locate the 4 swing arm hooks that are clipped midway on thetree trunk (clipped for storage purposes only) (Fig. 4a).
   
   
3. Unclip the 4 swing arm hooks and lower all 4 swing arm hooksto the tree's base (Fig. 4b).
   
4. Insert the hooks from the 4 swing arms into the eyelets located on the trees base (Fig. 5).
   

5. Lift the "top branch tree section" and insert into the top of the tree's trunk. Align and position the base of the "top branch tree section" into the "V" opening on the top of the tree's trunk (Fig. 6).
   
   
6. Insert the 2 swing arm hooks (located at the bottom of the "Top branch tree section") into the eyelets located on top portion of tree's trunk (Fig. 7).
   
   
7. Make the only male to female coaxial connection needed; the "top branch tree section" to the trees trunk. (Matching label #1 to label # 1) (Fig. 7a)
   

SHAPING OF THE TREE

1. Remove the velcro straps, binding the branches of the "topbranch tree section" together; being careful that the potential spring release of the branches does not cause injury.
2. Begin to gently guide the hinged branches downward to a desired position, being careful not to cause injury from the branch tips.
   NOTE: The top 3 branches are not hinged; they must be guided into a desired position.
3. Proceed to now shape thetree. The main branches, along with the branch tips, are flexible, and should be spread open to mirror that of a real bare branched tree (Fig 8).
   
4. To illuminate fully insert the plug into a working GFCI outlet oran outdoor rated extension cord.
5. Push or gently hammer support stakes into the groundsecuring the tree base. Angle each stake 45 degrees toward the center of the tree (Fig 9).
   
   
   You have completed the assembly of the tree (Fig 10).
   

REMOTE CONTROL OPERATION

Included is the remote control that operates the color and function of your outdoor tree.
Before operation; a standard 9 volt battery (6F22, 6LR61 or 23F6-220) must be installed into the remote control; by simply removing the slide plate located on the back of the remote control. The tree's 56 lighting function capability is controlled solely by the use of the remote control provided.
By simply depressing the color, function or ON/OFF button on the remote control; indicator lights will keep you on track as to the exact color and function that you are currently on.
Select your favorite color and your favorite function!

NOTE: When the tree is turned OFF by the use of the remote control; and is then turned back ON by the use of the remote control; the tree will resume the memory of the last color and function that was selected on the remote control.

TIMER FEATURE

Activating the timer mode:
Simply press the "timer" button on the remote control once (every other light on your tree sculpture will then flash RED 3 times) your tree's 6-hour timer has now been activated.

Deactivating the timer mode:
Depress the "timer" button once again (every other light on your tree sculpture will then flash GREEN 3 times) your tree's timer feature has now been deactivated.

PLEASE NOTE:
The moment that the "timer" button is pressed (activated), your tree sculpture will remain ON for exactly 6 hours. The tree will then automatically turn back ON exactly 18 hours later.

TROUBLESHOOTING

NOTE: Check the item for any loose, unlit or damaged bulbs. Although it will still operate, the bulbs must be replaced promptly to ensure the performance and life expectancy of the item.

NOTE: Replacement bulbs are provided. This is a specialty bulb. Do not replace with a standard LED or Incandescent bulb. Should you need additional bulbs please call our customer service department at 1-888-831-6656.

To determine which color replacement bulb is needed; select "Steady" function and "Christmas" color on your remote control.

1. If the tree does not illuminate press the on/off button on your remote control. If failure to light persists the battery may need to be replaced. Insert a standard 9 volt type battery (6F22, 6LR61 or 23F6-220); aligning the appropriate ( +/- ) markings accordingly.
   NOTE: By changing the remote angle slightly, or reducing your distance from the sculpture, you may achieve better remote control reception.
   If the tree fails to light due to a damaged or defective remote control; a new remote control can be provided through our customer service center.
2. A delayed response, while switching between color selections on the remote control, is in no way a malfunction of the light set, but is a normal operating response due to the complexity of the technology.
   All bulbs must independently receive their signal to alter to the correct color selected. Some bulbs receive their signals quicker than others, hence a delayed receiver response may occur. Again, this is a normal response based on the technology.
3. If a branch light set is unplugged from the trunk and then plugged in and branches don't synchronize, unplug the tree at the GFCI outlet and plug in again and all functions/colors should be the same on the whole tree.

STORAGE INSTRUCTIONS

1. Leave assembled if storage room permits or disassemble, placing all components in the original carton.
2. Store in cool, dry location away from sunlight.

NOTE: Store your remote control in a SAFE & DRY location and remove the battery from remote control before storage.

56 TOTAL LIGHT SETTINGS

• 11 colors Options - White, Red, Green, Blue, Yellow, Purple, Amber, Spring (Blue, Yellow, Purple), Patriotic (Red, Pure White, Blue), Fall (Green, Purple, Amber), Christmas (Red, Green, Blue, Yellow, Purple, Amber).
• 5 functions per color - Steady, Glisten, Firefly, Twinkling, Flash.
• + Color Morphing (7 colors – White, Red, Green, Blue, Yellow, Purple, Amber).

This is not a toy, for decorative use only.

Distributed by Santa's Best® Riverwoods, IL 60015 USA
www.santasbest.com

Documents / Resources

References

• Home Page - Santa's Best

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Santa's best LED15 - Outdoor Bare Branch Tree Sculpture Manual