Troubleshooting; Maintenance; Environmental Protection - Worx WX856.X Series Manual

reloading. Use extensive sweeping motion in the
crisscross pattern. Do not use a polisher to press the
surface down. Use the orbital action of the pad and
bonnet to do the work. After covering a flat surface,
polish curved surfaces such as car doors and quarter
panels. Use a small circular motion. After applying
polish to the entire surface, turn the polisher off. Wait
until the pad stops rotating before lifting the polisher
from the surface. (See Fig.E1)
Note: It is also convenient to use one hand to polish
the roof and car sides. (See Fig.E2)
Polish the smaller surfaces (SEE FIG. E3)
For hard to reach areas, such as the underside of
bumpers or side mirrors, apply polish by hand
6. CHANGE TO BUFFING/POLISHING BONNET
TO THE FOAM PAD (SEE FIG. F)
Place the wool bonnet on foam pad. Always make
sure that the elastic strip on the bonnet is securely
stuck to the foam pad
7. BUFFING AND POLISHING - REMOVING THE
WAX FROM THE SURFACE (SEE FIG. G)
NOTE: Wait until wax has dried to an even haze on
vehicle. Remove wax in the same order in which it
was applied.
Turn the polisher to the ON position. Polish and buff
the entire surface until all dried wax is removed.
Remove the bonnet from time to time and shake
out the residue. The bonnet with excess residue will
cause streaking. You may need to replace the bonnet
if you can't get it clean enough to avoid streaking.
10
Final buffing and polishing use a clean bonnet.
NOTE: For best results, use long, sweeping strokes
in a criss-cross pattern when removing wax.
WORKING TIPS FOR YOUR
POLISHER
1. For best results, the surface should be clean and
dry. Most high-gloss surfaces can be cleaned with
mild soap and water solution. To remove stubborn
dirt, such as road tar, grease, and bug stains, use a
mild ammonia solution, such as one used in glass
cleaners. Before using any cleaning product, follow
the instructions for use.
2. Always let the polisher work and do not force it or
apply excessive pressure on the polisher. Preferably,
use a light circular motion. Random orbital motion
on this tool is better when less pressure is applied.
Pressing too hard will slow down the machine's
movement and affect the quality of work.
3. However, the most common mistake is to use too
much wax. If pad absorbs too much wax, it will not
last long, and polishing is more difficult and takes
longer.
4. If bonnet continually comes off pad, please try
with a new bonnet.
5. If the wax seems difficult to polish, you may have
used too much wax. Apply wax in a thin, even coat.
Too much wax does not add any more protection and
20V Cordless Orbital Buffer
only makes the wax removal more difficult.

TROUBLESHOOTING

1. If the polisher does not abrade surface, checking
the bonnet. If the bonnet has been worn, replace the
new bonnet and try again.
2. If a fault can not be rectified, return the tool to an
authorized dealer for repair.

MAINTENANCE

Remove the battery pack from the machine
before carrying out any adjustment, servicing
or maintenance.
Your power tool requires no additional lubrication or
maintenance.
There are no user serviceable parts in your power
tool. Never use water or chemical cleaners to clean
your power tool. Wipe clean with a dry cloth. Always
store your power tool in a dry place. Keep the motor
ventilation slots clean. Keep all working controls free
of dust. Occasionally you may see sparks through
the ventilation slots. This is normal and will not
damage your power tool.
FOR BATTERY TOOLS
The ambient temperature range for the use and
storage of tool and battery is 0
The recommended ambient temperature range for
the charging system during charging is 0
(32°F-104°F).
ENVIRONMENTAL
PROTECTION
Disposal
The machine, its accessories and
packaging materials should be sorted for
environmentally friendly recycling.
The plastic components are labeled for categorized
recycling.
C-45 C(32°F-113°F).
o o
C-40 C
o o
EN