Summary of Contents for Lex Powergate PGIP12G-GWBRB-GKS
- Page 1 Input / Output Panels 1200A / 1600A Installation Instructions & User Manual A safe, convenient and reliable way to connect and access temporary power LM-PGIP16001200 - Rev. 001...
-
Page 2: Table Of Contents
Product Features (Input / Output) conjunction with transfer switch. Installation (Input / Output) Installation Continued (Input) Lex Products PowerGATE™ Input Panels are Listed to UL 1008. Set-up (Input) Lex Products PowerGATE™ Output Panels are Listed to UL 891 Disconnecting Circuits (Input) for Switchboards. -
Page 3: Prior To Installation: Site Preparation
(6) feet from the face of the panel – While key lock protection is provided, potential access by unauthorized personnel and vandals should be taken into consideration when locating this device. Figure 1 Contact Lex Products: 800.643.4460 info@lexproducts.com... -
Page 4: Product Features (Input / Output)
Phase Rotation Monitor and 2 Wire Start / Stop Terminals (Input Panel) Removable access panel for bottom entry installation Forklift Pockets Cable access door for mechanical strain reduction and theft deterrence Contact Lex Products: 800.643.4460 info@lexproducts.com... -
Page 5: Installation (Input / Output)
Place the punch on the inside of the enclosure and draw the punch through to the die on the outside 4. Vacuum entire upper chamber to ensure no metal shavings are left behind Figure 7 Forklift Pockets Contact Lex Products: 800.643.4460 info@lexproducts.com... - Page 6 350 MCM – Terminal crimp rings to have 1/2” opening 2. Secure ring terminals to bus bar Lex Products Part Number – LBL-PGIP-ROTATION – Use 1/2” bolts tightened to ninety-eight (98) foot pounds of torque Figure 9 3.
-
Page 7: Set-Up (Input)
Proper connection (See Figure 8): A. Grasp connector jacket and firmly Insert cam connector into cam plug B. Push on cam connector jacket until connector fully seats in cam plug C. Rotate cam connector jacket counterclockwise until it stops Contact Lex Products: 800.643.4460 info@lexproducts.com... -
Page 8: Disconnecting Circuits (Input)
2. Toggle the transfer switch, diverting power from utility to generator feed Proper disconnection (See Figure 12): A. Grasp connector jacket firmly and rotate cam connector clockwise until it stop B. Firmly pull on connector until it separates from the plug C. Set aside Contact Lex Products: 800.643.4460 info@lexproducts.com... -
Page 9: Installation (Output)
Failure to install transfer switch will create the potential for C. Rotate cam connector jacket counterclockwise until it stops the source to energize the Lex Products PowerGATE™ Power Output Panel and endanger installation personnel 3. Continue with connections, beginning with the rear of the cabinet and working forward The Lex Products PowerGATE™... - Page 10 A. Grasp connector jacket firmly and rotate cam connector counter clockwise until it stops B. Firmly pull on connector until it separates from the plug C. Set aside Step 10: Secure the three (3) key locks to complete procedure Contact Lex Products: 800.643.4460 info@lexproducts.com...
-
Page 11: Kirk Key Installation
– Lex Products Kirk Key Install Kit (comes with unit) provide a 360 ° seal. • Seeloc washer • Silicone Sealant – HD Series Kirk Key (Type D of DM) (not provided by Lex Products) Equipment Needed – Torque wrench –... -
Page 12: Product Feature Instructions (Input)
The PowerGATE™ Input / Output Panel will require periodic – Replace as needed maintenance. Lex Products recommends annual inspections to keep the panel in safe operating condition. Lex Products 4. Inspect all portable cables recommends that the Pre-Operation and Maintenance Checklist –... -
Page 13: Appendix B - Parts Dimensions
PowerGATE™ Power Input / Output Panel Appendix B Parts Dimensions Contact Lex Products: 800.643.4460 info@lexproducts.com... - Page 14 PowerGATE™ Power Input / Output Panel Appendix C Labels for Replacement - Input Panel Contact Lex Products: 800.643.4460 info@lexproducts.com...
- Page 15 PowerGATE™ Power Input / Output Panel Appendix C - Continued Labels for Replacement - Output Panel Contact Lex Products: 800.643.4460 info@lexproducts.com...
- Page 16 Dimensions 56” H x 35”W x 30”D Approximate Weight 505 lbs. Additional Cam options and enclosure materials available. Contact a Lex Products Sales Representative for more information. Lex Products Lex West www.lexproducts.com © Copyright Lex Products 2021 11 Forest Parkway 12701 Van Nuys Blvd.