ubicquia ubihub APAI AP6 Installation Manual

Hide thumbs Also See for ubihub APAI AP6:

Installation manual (10 pages)

Installation manual (20 pages)

page of 13

/ 13
Bookmarks

Quick Links

Download this manual

Installation Guide

Before installation, please read this

instructional guide completely and save

for future reference.

1. Product Overview

1.1

View of UbiHub parts from top

Shuttles

Dual-Camera

(APAI Only)

1.2

View of UbiHub parts from bottom

Ground Screw

Vertical Clamp

Adjument Screws

ALS Sensor

Top Female

NEMA Socket

Swivel Locking Nut

Open Cap

Bottom Male

NEMA Plug

Mounting Rails

Horizontal Clamp

Adjustment Screws

Need help?

Do you have a question about the ubihub APAI AP6 and is the answer not in the manual?

Questions and answers

Summary of Contents for ubicquia ubihub APAI AP6

Page 1 ALS Sensor Top Female NEMA Socket Shuttles Swivel Locking Nut Dual-Camera (APAI Only) View of UbiHub parts from bottom Open Cap Bottom Male NEMA Plug Ground Screw Mounting Rails Horizontal Clamp Adjustment Screws Vertical Clamp Adjument Screws © 2021 Ubicquia, Inc.
Page 2 Cleaning cassette for optical connectors Corrugated Board Ferrule end-face cleaner Shipping Box Grounding clamp CAUTION: Always wear a helmet and avoid standing in an area where objects Additional length of can fall. grounding cable (as needed) © 2021 Ubicquia, Inc.
Page 3 Ensure the mounting rails are Center Axis NEMA Socket facing upwards. Top Surface Vertical Distance NOTE: Record position horizontal and vertical dimensions on UbiHub and clamp for later use in multiple installations of the same luminaire type. © 2021 Ubicquia, Inc.
Page 5: Mounting The Unit
NOTE: Installer can use the provided camera during installation. The grounding cable or their own camera should be placed atop grounding cable, strap, or other pre- the unit during install, whenever installed method. possible. © 2021 Ubicquia, Inc.
Page 6 NOTE: CREE fixtures/NEMA will need to be locked in Verify the NEMA socket on the luminaire is oriented in the correct direction. The North indication on the NEMA (N >) should face away from the pole of the luminaire. © 2021 Ubicquia, Inc.
Page 7 Tighten the horizontal adjustment upward and securing with the swivel locking nut. Use the 1/2” screws to 40 in-lbs torque using the 3/16” Hex bit. deep drive socket to tighten the locking nut to 40 in-lbs torque. 3/16” 1/2” © 2021 Ubicquia, Inc.
Page 8 15 in-lbs torque using the or pinched. 3/16” Hex bit. 3/16” WARNING: Be sure to remove the red protective film from the dual-camera lenses. The dual-camera will not operate otherwise. © 2021 Ubicquia, Inc.
Page 9 NOTE: Steps may vary depending on what type of SFP module you are using. CAUTION: DO NOT touch or blow into the optical cable A. Fiber backhaul connectors or SFP module. B. Ethernet backhaul © 2021 Ubicquia, Inc.
Page 10 If connecting an IoT accessory appropriate gasket opening. continue to section 9. Otherwise close the UbiHub rear access door and secure by tightening the two screws using a #2 Phillips screwdriver. © 2021 Ubicquia, Inc.
Page 11 Remove the gasket plug and seat dual-camera lenses. the IoT accessory cable into the appropriate gasket opening. 10.3 Ensure all cables are properly connected and seated in the rear access door gasket. 10.4 Installation of the Ubihub is now complete. © 2021 Ubicquia, Inc.
Page 12 Cobra head luminaire mount 1.25” IPS pole Frequency bands ISM (2.4-2.484GHz) U-NII-1 (5.15-5.25GHz) Operating Humidity Up to 90% U-NII-2A (5.25-5.35GHz) Wind Survivability Up to 241km/h (150 mi/h) U-NII-2C (5.47-5.725GHz) Altitude Max 2000 m U-NII-3 (5.725-5.895GHz) © 2021 Ubicquia, Inc.
Page 13 • Suitable lightning arrester is intended to be installed during end installation as per applicable local and national codes or regulations. www.ubicquia.com © 2021 Ubicquia, Inc. All rights reserved. Patent(s) pending. Public use approved. 2058 v2 December 2021 © 2021 Ubicquia, Inc.

This manual is also suitable for:

Ubh-h-wi Ubh-h-ai