Introduction This booklet explains how to view the images you took with the PENTAX Optio 33L on your PC. Keep this manual in a safe place. Regarding copyrights Images taken using the Optio 33L that are for anything other than personal enjoyment cannot be used without permission according to the rights as specified in the Copyright Act.
Contents Introduction...2 Contents ... 3 Viewing Images on a Windows PC Software Provided ... 4 System Requirements ... 4 Installing the Software... 5 Installing the USB Driver ...5 Installing ACDSee™...7 Installing ACD photostitcher ...7 Displaying and Copying Images Using ACDSee™ ... 8 Panorama Image Stitching with ACD photostitcher...
Viewing Images on a Windows PC You can use the provided USB cable (I-USB2) or a card reader to transfer your images to the PC, and you can edit and print your images using the image viewing software. Here, the method for viewing images with the provided software (S-SW8) is explained.
Place the provided CD-ROM (S-SW8) in your PC CD-ROM drive. The [PENTAX Software Installer] screen is displayed. When the [PENTAX Software Installer] screen is not displayed Display the [PENTAX Software Installer] screen as follows: 1) Double-click [My Computer] on the Desktop screen.
With the camera turned off, connect the camera to the PC using the USB cable. Confirm that the CF card is inserted in the camera. Turn on the camera. The desktop screen will display [Found new hardware] (Windows XP) or [New Hardware Found] (Windows 98/98SE/2000), and the USB driver will be installed.
Installing ACDSee™ Once ACDSee™ is installed, you can edit and manage your pictures on your PC. Follow steps 1 through 3 on page 5 to display the [PENTAX Software Installer] screen. Click [ACDSee™]. The Setup screen is displayed. Follow the instructions on the screen to input registration information and install the software.
Displaying and Copying Images Using ACDSee™ Turn on your PC. With the camera turned off, connect the camera to the PC using the USB cable. Confirm that the CF card is inserted in the camera. Turn on your camera. ACDSee™ will start automatically, and display an image list. Proceed to step 5.
Copy images to your PC. Select an image to copy from the image list, and copy it to the destination folder. For details on copying procedures, see the user’s manual for your PC. You can copy images on Explorer as well, which is bundled with Windows.
Page 10
Correct the image positioning. ACD photostitcher starts, and the selected images are displayed in panorama format. Move the mouse pointer onto the image. It changes into a e symbol. Hold down the left mouse button and drag the images to adjust the stitching position.
Page 11
Trim the image. Move the mouse pointer onto an image. It changes into a Hold down the left mouse button and drag the dotted lines to adjust the image trimming position. When the position is adjusted, click the [Trimming] button. Save the image.
Double-click the [Unplug or eject hardware icon] in the task bar recognized area. The [Remove Hardware] screen will appear. Confirm that [Pentax USB Disk Device] is selected and click [Stop]. The [Stop Hardware Device] screen will appear. Confirm that [Pentax USB Disk Device] is selected and click [OK].
Windows XP Double-click the [Safely Remove Hardware] icon in the task bar recognized area. Click [PENTAX USB DISK Device] and click [Stop]. Click [PENTAX USB DISK Device Drive] and click [OK]. When a message is displayed permitting removal, turn the...
Install the required software as follows. Turn on your Macintosh. Place the provided CD-ROM (S-SW8) in your Macintosh CD-ROM drive. Double-click the CD-ROM (S-SW8) icon. Double-click the [Install ACDSee™] icon. Double-click the [Master Installer] alias icon. The [PENTAX Software Installer] screen will appear.
Click your applicable language. The software installation selection screen will appear. Installing the USB Driver (Mac OS 8.6 only) Click [USB Driver]. The USB driver is installed. When installation is complete, reboot your Macintosh. The provided USB driver does not need to be installed on Mac OS 9.0 or higher.
Displaying and Copying Images Using ACDSee™ Turn on your Macintosh. With the camera turned off, connect the camera to the Macintosh using the USB cable. Confirm that the CF card is inserted in the camera. Turn on your camera. The camera is recognized as an [untitled] on the desktop.
Copy images to your Macintosh. See your Macintosh user’s manual for how to copy or move files. Please copy images to your Macintosh before editing them. If the CF memory card has a volume label, the volume label name will be displayed instead of “untitled”.