Page 1: Table Of Contents
PROVIDED ACCESSORIES GETTING STARTED VHS CAMCORDER 6 – 13 RECORDING 14 – 29 Basic Recording ......14 GR-SXM607 Basic Features ......16 Zooming, 5-Sec. Recording, Picture Stabilizer, GR-SXM57 Quick Review, Video Light, Retake Advanced Features ...... 18 Snapshot, Night-Scope, Fade/Wipe Effects,...
Page 2: Safety Precautions
Dear Customer, Thank you for purchasing the JVC Compact VHS camcorder. Before use, please read the safety information and precautions contained in the following pages to ensure safe use of this product. Using This Instruction Manual • All major sections and subsections are listed in the Table Of Contents on the cover.
Page 3 Do not block the ventilation holes. anywhere. Use the JVC BN-V11U**/V12U/ (If the ventilation holes are blocked by a V20U/V400U battery packs and, to recharge newspaper, or cloth etc. heat may not be able to them or to supply power to the camcorder from get out.)
Page 4: Automatic Demonstration
AC Adapter, GR-FXM37/FX12 only) • Core Filter x 4 •Battery Pack (for provided A/V Cable, BN-V11U (GR-FXM37/FX12) S-Video Cable and AC Adapter, BN-V20U (GR-SXM607/SXM57/ GR-SXM607/SXM57/SXM47/ SXM47/SX202/SX22) SX202/SX22 only) •AAA (R03) Battery x 2 •A/V (Audio/Video) Cable (for Remote Control Unit, GR-SXM607/SXM57/SX202 only) •S-Video Cable...
Page 5 How To Attach The Core Filter Attach the provided Core Filter to the provided A/V Cable, S-Video Cable and AC Adapter. The Core Filter reduces interference. Release the stoppers on both ends of the Core Filter. 5 cm Run the cable through the Core Filter, leaving approx.
Page 6: Getting Started
● Using the optional AA-V15EG AC Power Adapter/ Charger, you can charge the BN-V11U/V12U/V20U/ * GR-FXM37/FX12 only. V400U battery pack without the camcorder. However, it **Provided with GR-SXM607/SXM57/SXM47/ cannot be used as an AC adapter. SX202/SX22 only. REFRESH: Charging a battery with some charge remaining reduces that battery’s capacity. Perform the procedure below to fully discharge the battery pack before recharging.
Page 7 (190) When using models equipped with LCD monitor When using GR-SX202/SX22/FX12 ( ) : when the video light is on (GR-SXM607/SXM57/SXM47/SX202/SX22 only) NOTES: ● Recording time is reduced significantly under the following conditions: • Zoom or Record-Standby mode is engaged repeatedly.
Page 8 GETTING STARTED (cont.) Grip Adjustment Power Zoom Lever Separate the Velcro strip. Recording Pass your right hand through the loop and grasp the Start/Stop Button grip. Adjust so that your thumb and fingers can easily operate the Recording Start/Stop Button and Power Zoom Lever.
Page 9 Date/Time Settings MENU Wheel Set the Power Switch to “ ”. The power lamp comes on. Press MENU. The Menu Screen appears. Rotate MENU to select “ TO SYSTEM MENU” and press it to display SYSTEM MENU. Rotate MENU to select “...
Page 10 GETTING STARTED (cont.) Recording Format Setting MENU Wheel (GR-SXM607/SXM57/SXM47/SX202/SX22 only) Set the recording format according to the format of the tape used or type of recording you wish to perform. NOTE: S-VHS ET recording is not possible when the recording mode is set to “LP”.
Page 11: Recording
Super VHS VCR. — Tapes recorded in S-VHS ET mode cannot be played back on some VCRs, including some JVC VCRs. Tapes recorded in S-VHS or S-VHS ET mode cannot be played back correctly on a normal VHS VCR.
Page 12 GETTING STARTED (cont.) Recording Mode Setting MENU Wheel Set the tape recording mode depending on your preference. Set the Power Switch to “ ”. The power lamp comes on. Press MENU. The Menu Screen appears. Rotate MENU to select “ TO SYSTEM MENU” and press it to display SYSTEM MENU.
Page 13 Loading/Unloading A Cassette EJECT Switch Cassette holder Open the LCD monitor fully (models equipped with LCD monitor only). Slide EJECT until the cassette holder opens. Do not use force to open. Insert or remove a cassette. When inserting, make sure the label is facing outward. Press the Close button to close the cassette holder until it locks into place.
Page 14: Basic Recording
RECORDING Basic Recording NOTE: You should already have performed the procedures listed below. If not, do so before continuing. ● Power ( pg. 6) ● Load A Cassette ( pg. 13) ● Recording Mode Setting ( pg. 12) ● Tape Length Setting ( pg.
Page 15 NOTES: ● If the Record-Standby mode continues for 5 minutes without performing Zoom or any other operations, the camcorder’s power shuts off automatically. Set the Power Switch to “OFF”, and then back to “ ” or “ ” to turn the camcorder on again. ●...
Page 16: Basic Features
RECORDING Basic Features Zooming: To produce the zoom in/out effect, or an instantaneous change in image magnification. Zoom in (T: Telephoto) Digital circuitry extends the maximum magnification offered by optical zoom. This system is called Digital Zoom. Zoom In Slide the Power Zoom Lever towards “T”. Zoom Out Slide the Power Zoom Lever towards “W”.
Page 17 When operating, keep a distance of about 30 cm between the video light and people or objects. Do not use near flammable or explosive materials. It is recommended that you consult your nearest JVC dealer for replacing the video light. Downloaded from: https://www.usersmanualguide.com/...
Page 18: Advanced Features
RECORDING Advanced Features Snapshot SNAPSHOT Button (GR-SXM607/SXM57/SX202 only) (GR-SXM607/SXM57/SX202 only) Use your camcorder like a regular camera and take a snapshot, or several of them in succession. Set the Power Switch to “ ” or “ ”. Press SNAPSHOT. If you press during Record-Standby . . .
Page 19 Fade/Wipe Effects FADE/WIPE Button These effects let you make pro-style scene transitions. Fade- or wipe-in works at recording start, and fade- or wipe-out works at recording end. Set the Power Switch to “ ”. Press FADE/WIPE repeatedly until the desired mode’s name and indication appear.
Page 20: Program Ae With Special Effects
RECORDING Advanced Features (cont.) Program AE With Special Effects P.AE Button Set the Power Switch to “ ”. Press P.AE repeatedly until the desired mode’s name and indication appear. They are displayed for approx. 2 seconds, then the name disappears so that only the indication remains. The mode is activated.
Page 21 16) cannot be activated during the “CLASSIC FILM”, Adds a “ghost” to the subject, giving your recording a “STROBE” and “VIDEO ECHO” mode. “fantasy” feeling. Zoom magnification of over 10X is not available. * GR-SXM607/SXM57/SX202 only. Downloaded from: https://www.usersmanualguide.com/...
Page 22 RECORDING Advanced Features (cont.) Using Menus For Detailed Adjustment This camcorder is equipped with an easy-to-use, on-screen menu system that simplifies many of the more detailed camcorder settings. Set the Power Switch to “ ”. MENU Wheel Press MENU. The Menu Screen appears. Power Switch Rotate MENU to select the desired function.
Page 23 Allows you to record black bars at the top and bottom of the screen to produce a cinema-like “wide-screen” effect. If a snapshot (GR-SXM607/SXM57/SX202 only, pg. 18) is taken while the camcorder is in the WIDE mode, the snapshot image is recorded without the black bars at the top and bottom of the screen.
Page 24 Advanced Features (cont.) SYSTEM MENU (cont.) Records in S-VHS on a VHS or S-VHS cassette ( pg. 10). S-VHS* (S-VHS ET*) (GR-SXM607/ SXM57/SXM47/ Records in VHS on a VHS or S-VHS cassette ( pg. 10). SX202/SX22 only) Allows you to set the tape length depending on the tape used ( pg.
Page 25 Date/Time Insert Set the Power Switch to “ ”. Allows you to display the date and time in the camcorder or on a connected colour monitor, Press MENU. The Menu Screen appears. as well as to record them manually or automatically.
Page 26 RECORDING Advanced Features (cont.) Animation NOTE: Before performing the following steps, make You can shoot a series of pictures, each slightly different, sure that: of the same object for a brief period of time. ● The Power Switch is set to “ ”.
Page 27 Exposure Control This feature automatically adjusts the iris for the best available picture quality, but you can override it and make the adjustment manually. Manual exposure adjustment is recommended in the following situations: • When shooting using reverse lighting or when the MENU Wheel background is too bright.
Page 28 RECORDING Advanced Features (cont.) Focusing Focus detection zone AUTO FOCUS The camcorder’s Full Range AF system offers continuous shooting ability from close-up to infinity. However, correct focus may not be obtainable in the situations listed below (in these cases use manual focusing): •...
Page 29: Manual White Balance Operation
White Balance Adjustment Manual White Balance Operation A term that refers to the correctness of colour Perform Manual White Balance when shooting under reproduction under various lighting. If the white various types of lighting. balance is correct, all other colors will be accurately Follow steps 1 through 4 of the white balance reproduced.
Page 30: Playback
2) To resume normal playback, press 4/6 again. ● Noise bars will appear and the picture will become monochrome during Still Playback. ● If TBC ( pg. 31) is engaged, noise bars will not appear. This mode is called Fine Still (GR-SXM607/SXM57/ SX202 only). Shuttle Search: Allows high-speed search in either direction.
Page 31: Features
Playback Special Effects (CLASSIC FILM, MONOTONE, SEPIA, STROBE and VIDEO ECHO, pg. 21) (GR-SXM607/SXM57/ SX202 only) Allows you to add creative effects to the playback image. 1) Activate the TBC mode and Auto Tracking. 2) Press DIGIFECT repeatedly until the desired mode’s name and indication appear.
Page 32: Connections
Video Output Connector cover* * When connecting the cables, open this cover. ** Provided with GR-SXM607/SXM57/SXM47/SX202/SX22 only. Connect when the TV or VCR has an S-video input. If your TV/VCR has a 21-pin connector Use the provided Cable Adapter. GR-FXM37/FX12...
Page 33 VCR using the then stop the VCR and camcorder when provided S-Video cable. This can improve the finished. dubbed picture quality (GR-SXM607/SXM57/ SXM47/SX202/SX22 only). ● To monitor the picture and sound from the camcorder without inserting a tape, set the camcorder’s Power Switch to “...
Page 34: Using The Cassette Adapter
VHS VCR. Playback is possible with a VCR equipped with the S-VHS function Compact video cassette (GR-SXM607/SXM57/SXM47/SX202/SX22 only). ● During special-effect playback (slow motion, still frame, etc.), the picture may vibrate or noise bars may appear on the screen.
Page 35: Using The Remote Control Unit (Gr-Sxm607/Sxm57/ Sx202 Only)
USING THE REMOTE CONTROL UNIT (GR-SXM607/SXM57/SX202 only) The Full-Function Remote Control Unit can operate this camcorder from a distance as well as the basic operations (Playback, Stop, Pause, Fast-Forward and Rewind) of your VCR. RM-V715U RM-V700U (optional) (provided) & Functions Buttons With the camcorder’s Power Switch set...
Page 36 USING THE REMOTE CONTROL UNIT (cont.) (GR-SXM607/SXM57/SX202 only) Installing The Batteries (RM-V715U, provided) The remote control uses two ”AAA (R03)” size batteries. See “General Battery Precautions” pg. 52). Open the battery compartment cover as illustrated. Insert two ”AAA (R03)” size batteries in the correct direction.
Page 37: Playback Zoom
Playback Zoom Remote sensor To magnify the recorded image up to 10X at any time during playback. NOTES: ● Use the RM-V715U remote control unit to perform this procedure. ● Make sure that the TBC mode is activated ( pg. 31). 1) Press PLAY to find the scene of interest.
Page 38: Insert Editing
USING THE REMOTE CONTROL UNIT (cont.) (GR-SXM607/SXM57/SX202 only) Insert Editing COUNTER R/M Button You can record a new scene onto a previously recorded tape, replacing a section of the original recording with minimal picture distortion at the in- and out-points. The original audio remains unchanged.
Page 39: Audio Dubbing
Audio Dubbing Display Audio dubbing You can record a new soundtrack on a prerecorded tape. M – 0 : 0 5 : indicator The existing original sound is erased and replaced by the sound from the built-in microphone. Perform steps 1, 2 and 3 of the Insert Editing procedure pg.
Page 40: Random Assembly Editing
PHILIPS Editing. 6 4 9 5 1 1 IMPORTANT 9 4 Although the MBR is compatible with JVC VCRs and BLAUPUNKT 9 1 those of many other makers, it may not work with 9 7 9 6 FERGUSON yours or may offer limited functions.
Page 41 JVC VCR EQUIPPED WITH REMOTE PAUSE TERMINAL Connect the editing cable to the Remote PAUSE terminal. J terminal (JLIP) To S-Video JVC VCR NOT EQUIPPED WITH REMOTE Open output the cover. PAUSE TERMINAL BUT EQUIPPED WITH connector R.A. EDIT CONNECTOR To Video* output Connect the editing cable to the R.A.EDIT...
Page 42 USING THE REMOTE CONTROL UNIT (cont.) (GR-SXM607/SXM57/SX202 only) SELECT SCENES Remote sensor Point the remote control at the camcorder’s remote sensor. Press PLAY, then press ON/OFF on the remote control. The R.A. Edit counter display appears. Press REW or FF to locate the beginning of the scene you want, then press IN/OUT to register that point.
Page 43 AUTOMATIC EDITING TO VCR Original tape (camcorder) Rewind the tape in the camcorder to the beginning of IN OUT the scene you want to edit and press PAUSE. Point the remote control towards the VCR’s infrared sensor and press VCR REC STBY, or manually engage the VCR’s Record-Pause mode.
Page 44: Details
Detach the battery from the camcorder. • Date/Time The date/time cannot be stored in memory if the built-in clock battery runs out. Consult an authorized JVC dealer for replacement, Settings or set the date/time as necessary before you start shooting. pg. 9) Downloaded from: https://www.usersmanualguide.com/...
Page 45 I T E M S N O T E S Recording When the Power Switch is set to “ ” or “ ” and the LCD monitor is opened at an angle of 60 degrees or more, the LCD pg. 14, 15) monitor switches on and the viewfinder switches off automatically to save power (models equipped with LCD monitor only).
Page 46: Troubleshooting
TROUBLESHOOTING If, after following the steps in the chart below, the problem still exists, please consult your JVC dealer. The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio, etc.) might prevent it from functioning properly. In such cases, first disconnect its power supply unit (battery pack, AC Adapter, etc.);...
Page 47 ● Turn the camcorder’s power off, then disconnect the power source. After a few minutes, try turning the power on again. If the error number still appears in the viewfinder, consult your nearest JVC dealer. The image is out of focus. ● The dioptre needs to be adjusted ( pg.
Page 48: Index
INDEX Controls, Connectors And Indicators 6 7 8 9 & Downloaded from: https://www.usersmanualguide.com/...
Page 49 • It is used to connect the camcorder to a device •Counter Reset/Memory Button such as a personal computer. [COUNTER R/M] ......pg. 31 For further details consult your nearest JVC Program AE Button [P. AE] ....pg. 20 dealer. Digital Effect Button [DIGIFECT] ..
Page 50: Indications
P.AE, Bright Level Indicator (models then only the indicator remains at equipped with LCD monitor only) ..pg. 14 • Night-Scope Indicator (GR-SXM607/ Instant Title Display ......pg. 25 SXM57/SX202 only) ...... pg. 18 Displayed at for approx.
Page 51 (battery, UNIT IN etc.) and wait a few minutes for them to clear. When it does, you can resume using the SAFEGUARD MODE camcorder. If the indication remains, consult your nearest JVC dealer. REMOVE AND REATTACH BATTERY Downloaded from:...
Page 52: Cautions
2. To prevent damage and prolong service life . . . • It is recommended that you consult your nearest ... do not subject to unnecessary shock. JVC dealer for replacing the video light..avoid repeated charging without fully discharging.
Page 53 Cassettes Main Unit To properly use and store your cassettes, be sure to 1. For safety, DO NOT . . . read the following cautions: ... open the camcorder’s chassis..disassemble or modify the unit. 1. During use ..
Page 54 Remove dust using a blower brush. RE-ATTACH EYEPIECE If malfunctioning occurs, stop using the unit Re-attach the eyepiece and turn it clockwise. immediately and consult your local JVC dealer. NOTES: ● Avoid using strong cleaning agents such as benzine or alcohol.
Page 55: Specifications
: 200 mm x 112 mm x 118 mm (W x H x D) (GR-SXM607/SXM57/SXM47/ Some accessories are not available in some areas. Please consult your nearest JVC dealer for details on accessories FXM37 only) and their availability. 200 mm x 112 mm x 115 mm...
Page 57 This file has been downloaded from: www.UsersManualGuide.com User Manual and User Guide for many equipments like mobile phones, photo cameras, monther board, monitors, software, tv, dvd, and othes.. Manual users, user manuals, user guide manual, owners manual, instruction manual, manual owner, manual owner's, manual guide, manual operation, operating manual, user's manual, operating instructions, manual operators, manual operator, manual product, documentation manual, user maintenance, brochure, user reference, pdf manual Downloaded from:...

This manual is also suitable for:

Gr-sxm57 Gr-sxm47 Gr-sx202 Gr-sx22 Gr-fxm37 Gr-fx12 ... Show all

JVC GR-SXM607 Instructions Manual

Quick Links

Related Manuals for JVC GR-SXM607

Summary of Contents for JVC GR-SXM607

This manual is also suitable for:

Table of Contents