Cooper Wiring Devices 6109 User Manual

6109
Motion Sensing
Wall Switch
The 6109 Motion Sensing Wall Switch dectects motion to turn on
AUTO
lights for an adjustable amount of time. A built-in photo cell can be
ON
set to keep lights off when the lights aren't needed. The unit has
excellent sensitivity and a wide 180 0 detection range. It can be used
with incandescent lighting as well as rapid start fluorescent lighting.
Two LEDs allow for easy mode identification. (Not for use with elec-
tronic ballasts)
Installation is as easy as replacing a wall switch. However, some
codes require installation by a qualified electrician.
Features include:
• 180 0 motion detection angle
• Adjustable on-time from 12 sec. to 30 min.
• Adjustable photocell
• Works with incandescent and rapid start fluorescent lighting (Not
for use with electronic ballasts)
• Works with motors up to 1/6 hp.
• Push button selectable ON AND AUTO modes.
Included are: • The sensor switch • Cover plate • 3 wire connectors • 2 large screws • 2 small screws.
INSTALLATION
40'
WARNING: For indoor use only.
SELECT A LOCATION
NEW APPLICATION
Choose a location where the motion sensor has a clear view of
the entire area where occupant motion may occur.
RETROFIT APPLICATION
20'
Motion sensing switch will replace existing wall switch. Use only
0'
where the existing switch location provides a clear view of the
occupied area. Typical Plan View of Coverage
GENERAL APPLICATION INFORMATION
The detector is more sensitive to motion across the front of the sensor than to motion towards the sensor.
The detector senses heat in motion and possible heat sources that change temperature quickly. Therefore, to
avoid false triggering, avoid placing the sensor where it will be aimed at air conditioners, heaters, and other
sources of heat or cold.
INSTALLING THE SWITCH
WARNING: Turn power off at the circuit breaker before wiring.
• Remove the decorative coverplate (secured by two
decorative screws).
• Remove Control Cover (pinch the Control Cover at
the indicated points and pull).
• Remove the existing switch (if this is a retrofit
application).
• Connect the detector as shown in the diagram.
Before installing the detector into the box, make
sure there is no wire exposed at the connection.
• Do not connect to neutral wire or damage to unit will
occur.
BLACK LOAD
LIGHTING
Control Cover
LOAD
Plate Removed
to access
adjustments
AUTO
screws
ON
TIME TIME LIGHT
MODE
Selection
BLACK
Switch
TYPICAL INSTALLATION
• Mount the detector into the wall box with the mounting screws.
• For test purposes, use a small screwdriver to turn the time control fully counter-clockwise
and the light control fully clockwise. Turn the power back on at the circuit breaker.
• Press MODE selection push button until the AUTO LED is on. Lamp will be on for 12 seconds. Allow two
minutes for the unit to warm up. If motion is detected, the lights will turn on. The lights will turn off 12 sec-
onds after motion is no longer detected.
Questions? Call 1-866-853-4293 8:00 AM to 7:00 PM Eastern Time, weekdays
- 2 -
469MX-PT
ADJUSTMENTS
TIME
The length of time that the lights stay on is
adjustable from 12 seconds to 30 minutes.
• Use a small screw driver to set the time by
using the diagram below as a guide.
12 Sec.
AUTO LED
AUTO
ON
Pinch Pinch
here here 30 Min.
T I M E
Note:
Adjustment screws
(NEUTRAL)
found under (off-auto-
on) face plate.
Green ground wire to
junction box screw or
grounding wire
Complete Installation
• Replace control panel cover and install the decorative wall plate. In installations where the Cooper motion
sensor switch is combined with other switches or outlets on an expanded box, a combination wall plate will
need to be purchased. Various combination wall plates are available at Home Centers and Electrical Supply
HOT
Stores.
(LINE)
• Press the push button a couple of times to make sure it operates freely.
USE
MODE Selection Switch
Pressing the pushbutton selects one of three modes of operation: ON, OFF, AUTO
ON: Lights stay on continuously. The ON led is lit.
OFF: Lights stay off. The AUTO led and the ON led are not lit.
AUTO: Lights come on for time set when motion is detected and the light level is below the set level.
The AUTO led is on and the ON led is off.
*When in the OFF mode, the circuit is still alive. Turn off circuit breaker before re-lamping.
LIGHT LEVEL
If you have a problem with your Wall Switch, first follow this guide. If the problem persists, call the customer
The sensor can be prevented from turning on lights when
service hotline at 1-866-853-4293 between 8:00 AM and 7:00 PM ET weekdays.
there is already enough light in the room. Use a small
screw driver to set the light level using this SYMPTOM
diagram as a guide. In the fully clockwise position, the
sensor turns on lights even in full daylight. In the fully
Light does not
counter-clockwise poition, the sensor only turns on lights come on.
when the surrounding light level is very low.
To adjust the photocell:
Dark (low
Any Light
light level) • When the light in the room is at
Level
the level you want the lights to
turn on, set the switch to the
+ +
AUTO position.
• Put the TIME control to the 12
sec. (fully counter-clockwise)
position.
Lights do not
• Put the LIGHT control to the mini-
stay on in the
mum dark (fully counter-clock-
Auto mode.
L I G H T
wise) position.
• Wait for the lights to turn off.
• Turn the LIGHT adjustment clock-
wise in very small steps and wait
2 seconds before moving your
SPECIFICATIONS
hand in front of the sensor.
Repeat until the lights controlled
by the sensor come on. The light
Electrical input....................................................................................................................................120V, 60 Hz
will now come on when the light
Fluorescent Load (not for electronic ballasts).....................(2) 30 Watt minimum 400 Watt maximum Rapid Start
level is at or below the present
Motor Load........................................ ........................................................................................1/6 HP maximum
level and motion is detected.
Incandescent.............................................................................................................................500W at 120V AC
On-Time...........................................................................................Adjustable approximately 12 sec. to 30 min.
Photocell Sensor..........................................................................................From dull daylight to less than 1 FC.
Coverage.............................................................................up to 20 ft. at 180
Dimensions .........................................................................................4.10 in. high, 1.7 in. wide and 2.00 in. deep
YOUR COOPER WIRING DEVICES ASSEMBLED PRODUCT TWO YEAR LIMITED WARRANTY
For a period of 2 years from the date of purchase, Cooper Wiring Devices will replace or repair the motion
sensing switch provided that it has not been subject to abuse, improper installation or improper use, and is
returned prepaid to Cooper Wiring Devices Quality Control Department at 203 Cooper Circle, Peachtree City,
GA 30269. If the product has been discontinued, replacement will be made with the nearest available equiva-
lent model. This warranty does not cover consumables (such as fuses). Proof of purchase in the form of a
bill of sale or receipted invoice that shows that the item is within the applicable warranty period must be pre-
sented to obtain the repair or replacement provided by the warranty. Repair or replacement as provided
under this warranty is the exclusive remedy of the customer. Cooper Wiring Devices shall not be liable for
any incidental or consequential damages for breach of any express or implied warranty on any of its prod-
ucts. Except to the extent limited or prohibited by applicable law, any implied warranty of merchantability or
fitness for a particular purpose on this product is limited in duration to the duration of this warranty. Some
states do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on
how long an implied warranty lasts, so the above limitations may not apply to you. This warranty gives you
specific legal rights and you may also have other rights which vary from state to state.
- 3 -
TROUBLESHOOTING
POSSIBLE CAUSE SYMPTOM POSSIBLE CAUSE
1.
Circuit breaker or fuse is turned Light does 1. Incorrect wiring.
off. not turn off. 2. MODE switch is set to ON
2. If the lamp being controlled has instead of AUTO.
another switch, it may be turned 3. Motion is still present.
off. 4. Delay set by TIME control
3. Bulb is defective. has not expired.
4. LIGHT control is set too far
toward the DARK position.
1. Heating or cooling ob-
Light comes
5.
MODE switch is set to OFF
jects (such as air vents,
on for no
instead of AUTO.
appliances, or drafts through
reason in
6. Incorrect wiring.
the the wall box) are causing
Auto mode. false triggering.
1. Motion has stopped in the room.
Switch on the sensor has
TIME control is set for too short a
2. been turned off and back on.
2. delay.
There was a momentary
power interrup-tion. The light
will turn off automatically
3.
when the "on" time expires.
0 , up to 40 ft. in front of the sensor
598-1179-02 E
- 4 -