Advertisement

Quick Links

KX3 Touchscreen
PRODUCT SAFETY
When using electrical equipment, basic safety precautions should always be followed, including the following:
READ THESE INSTRUCTIONS BEFORE USING THIS PRODUCT.
Do not let power supply cords touch hot surfaces.
Do not mount near gas or electric heaters.
Do not use the unit near water.
Do not allow objects to fall or liquids to be spilled
into the enclosure through openings.
Equipment should be mounted in locations and at
heights where it will not readily be subjected to
tampering by unauthorized personnel.
SAVE THESE INSTRUCTIONS.
GETTING STARTED
Overview
The Encelium KX3 Touchscreen Panel is a 89 mm (3.5 inches) flush-mount LCD touchscreen display that provides the ability to
recall multiple lighting scenes for a given zone. It's ideal for large multi-purpose spaces where lighting requirements vary
throughout the day, such as an auditorium or conference room.
INSTALLATION INSTRUCTIONS
The use of accessory equipment is not recommended
by Encelium as it may cause an unsafe condition.
Do not use this equipment for other than the
intended use.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KX3 Touchscreen and is the answer not in the manual?

Questions and answers

Summary of Contents for Encelium KX3 Touchscreen

  • Page 1 GETTING STARTED Overview The Encelium KX3 Touchscreen Panel is a 89 mm (3.5 inches) flush-mount LCD touchscreen display that provides the ability to recall multiple lighting scenes for a given zone. It's ideal for large multi-purpose spaces where lighting requirements vary...
  • Page 2: System Overview

    KX3 Touchscreen INSTALLATION INSTRUCTIONS SYSTEM OVERVIEW Wired System Overview With Encelium X, you can control DALI devices exclusively or a mixture of GreenBus and DALI. GreenBus DALI KX3 Touchscreen Installation Instructions...
  • Page 3 KX3 Touchscreen INSTALLATION INSTRUCTIONS Wireless System Overview This illustration shows how each component is easily integrated into the Encelium X Lighting Control System. KX3 Touchscreen Installation Instructions...
  • Page 4: Mounting Option

    The KX3 Touchscreen is designed for flush-mount, in-wall installations. It requires an available mounting depth of 52.5 mm (2 inches) from the surface of the wall. The recommended mounting height for the KX3 Touchscreen is between 1.4 and 1.5 m (4.5 and 5 ft) from the bottom of the faceplate.
  • Page 5: Installation

    The KX3 Touchscreen shall be installed in dry, indoor locations ONLY. RS-232 (1) RS-232 (2) CONTROL ETHERNET Front View Rear View The KX3 Touchscreen has the following built-in components: ambient and proximity sensors and reset button. Reset Button Ambient and Proximity Sensors KX3 Touchscreen Installation Instructions...
  • Page 6: Electrical Connections

    KX3 Touchscreen INSTALLATION INSTRUCTIONS ELECTRICAL CONNECTIONS KX3 Touchscreen Wiring Diagram GreenBus To Additional Wired Managers (As Needed) CONTROL Ethernet Cable 91.4 m (300 ft) maximum (Typical) To secure LAN Port for PC Lighting Control (Requires Static IP Address) Power Supply Wired Manager —...
  • Page 7: Ethernet Port Wiring

    KX3 using PoE, a 802.3af Compliant class 3 PoE switch must be used. RS-232 (1) RS-232 (2) CONTROL ETHERNET BUTTON KEYCAP REPLACEMENT The KX3 Touchscreen hard button keycaps are compatible with the Laser Shark custom button etching service. REMOVING BUTTON KEYCAPS Remove the KX3 bezel. KX3 Touchscreen Installation Instructions...
  • Page 8: Installation Instructions

    Gently press straight down on the keycap until it is seated flush with the display. TROUBLESHOOTING There are no user-serviceable parts inside. For detailed information about how to set-up, install, use, and maintain Encelium hardware and software, please visit: help.encelium.com Copyright ©...

Table of Contents