Page 1
FILE NO. 120-200152 SERVICE MANUAL VIDEO CASSETTE RECORDER V-621EW MAY, 2001...
Page 2
TOSHIBA VIDEO PRODUCTS PTE LTD 438B ALEXANDRA ROAD BLOCK B #06-01 ALEXANDRA TECHNOPARK SINGAPORE 119968...
Page 3
TOTAL CONTENTS 1. Precautions 2. Reference Information 3. Product Specifications 4. Disassembly and Reassembly 5. Alignment and Adjustment 6. Exploded View 7. Replacement Parts List 8. Block Diagram 9. PCB Diagrams 10. Schematic Diagrams...
Page 4
Alternatively, wear a discharging Wrist-strap device. (Be sure to remove it prior to applying power--this is an electric shock precaution.) Toshiba...
Page 5
Always inspect for pinched, out- of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts. Toshiba...
Page 6
2. Reference Information 2-1 Operation of Controls Toshiba...
Page 23
Reference Information 2-2 IC Blocks 2-2-1 IC301 (LA71598M) 2-18 Toshiba...
Page 24
Reference Information 2-2-2 IC501 (LA72634AM) Toshiba 2-19...
Page 25
Reference Information 2-2-3 IC601 (uPD784928) 2-20 Toshiba...
Page 26
Reference Information MEMO Toshiba 2-21...
Page 27
68 dB min (IHF A filter) Frequency response 20Hz - 20kHz Power requirement 230V (AC 50-60 Hz) Power consumption Approx. 17 watts Operation temperature 41°F-104°F (5°C-40°C) Operation humidity 10%-75% Weight 2.8 Kg (net) Dimensions (WxHxD) 360 x 94 x 252 mm Toshiba...
Page 29
4-1-4 Ass’y F-A/V PCB Removal Disconnect the CN708 from the Ass'y PCB-Main ´ Lift up the Bottom Cover in the direction of arrow. and then lift the Ass'y F/AV PCB up. Fig. 4-2 Bottom Cover Removal Fig. 4-4 Ass’y F-A/V PCB Removal Toshiba...
Page 30
4-1-5 Chassis Removal ˇ 3 SCREWS ¨ Lift the Ass'y Deck up. Ø Lift the Ass'y Main PCB up to Remove. Œ 2 SCREWS ˆ RELEASE 1 TAB ASSEMBLY POINT (ALIGN TWO ARROWS) PUSH ´ BRACKET-FRAME Fig. 4-5 Chassis Removal Toshiba...
Page 31
4-2-1 Top View Œ ´ ˇ ¨ ˆ Ø Fig. 4-6 Top parts Location-1 Œ GEAR FL CAM ´ MOTOR LOADING ASS’Y ˇ LEVER FL ARM ASS’Y ¨ HOLDER FL CASSETTE ASS’Y ˆ LEVER FL DOOR Ø SLIDER FL DRIVE Toshiba...
Page 32
´ CYLINDER ASS’Y ˝ GEAR IDLE ˇ ACE HEAD ASS’Y Ô LEVER IDLE ¨ LEVER UNIT PINCH ASS’Y LEVER T BRAKE ASS’Y ˆ LEVER #9 GUIDE ASS’Y Ò DISK T REEL Ø LEVER TENSION ASS’Y ∏ BAND BRAKE ASS’Y Toshiba...
Page 33
Œ GEAR JOINT 1 ´ GEAR JOINT 2 ˇ BRACKET GEAR ¨ MOTOR CAPSTAN ASS’Y ˆ LEVER T LOAD ASS’Y Ø GEAR LOADING DRIVE ∏ LEVER S LOAD ASS’Y ” HOLDER CLUTCH ASS’Y ’ BELT PULLEY ˝ SLIDER CAM Toshiba...
Page 34
Lever FL Cassette-R ´ at disassembling and "B" reassembling. ´ LEVER FL DOOR ˇ HOOK "C" Fig. 4-9 Lever FL Door Removal RAIL [B] Œ HOLDER FL ´ LEVER FL CASSETTEE -R CASSETTEE ASS`Y "A" BOSS [A] Fig. 4-10 Holder FL Cassette Ass’y Removal Toshiba...
Page 35
Œ LEVER FL ARM ASS`Y Fig. 4-13 Lever FL Arm Ass’y Removal ´ GEAR FL CAM Œ SLIDER FL DRIVE Fig. 4-11 Slider FL Drive Removal Œ GEAR FL CAM GEAR WORM WHEEL POST TIMING POINT Fig. 4-12 Gear FL Cam, Gear Worm Toshiba...
Page 36
1) Remove the screw Œ. 1) Remove the Gear Worm wheel Œ. 2) Remove the Motor Loading Ass’y ´. ´ MOTOR LOADING ASS`Y Œ SCREW Œ GEAR WORM WHEEL Fig. 4-15 Motor Loading Ass’y Removal Fig. 4-14 Gear Worm Wheel Removal Toshiba...
Page 38
LEVER LOAD T LEVER LOAD S Lever Tension Drive Removal TIMING POINT 2 TIMING POINT 3 PIN A PIN C PIN D PIN B ˇ SLIDER CAM Fig. 4-19 Gear Loading Drive, Slider Cam, Lever Load S, T Ass’y Assembly Toshiba 4-10...
Page 39
ˇ SPRING BRAKE Œ SPRING TENTION LEVER STOPPER Œ LEVER S BRAKE ASS`Y "A" HOOK(C) MARK[B] HOOK(B) ´ LEVER T BRAKE ASS`Y Fig. 4-21 Lever Tension Ass’y, Band Brake Ass’y Removal Fig. 4-22 Lever Brake S, T Ass’y Removal 4-11 Toshiba...
Page 40
´ DISK T REEL add oil in the boss of Lever Idle Œ. "A" Œ LEVER IDLE ´ GEAR IDLE "B" ´ GEAR IDLE HOOK "C" Fig. 4-24 Disk S, T Reel Removal Fig. 4-23 Gear Idle Ass’y Removal Toshiba 4-12...
Page 41
DETAIL B Fig. 4-26 Lever Up Down Ass’y Removal SPRING GEAR CENTER ASS'Y GUIDE LEVER UP DOWN ASS'Y RING <BAD> <GOOD> GEAR POST HOOK Fig. 4-25 Holder Clutch Ass’y Removal MAIN BASE Fig. 4-27 Lever Up Down Ass’y Removal 4-13 Toshiba...
Page 42
Œ GUIDE CASSETTE DOOR Œ LEVER UNIT PINCH ASS`Y HOOK [A] ´ PLATE JOINT ˇ SPRING PINCH DRIVE Fig. 4-28 Guide Cassette Door Removal Fig. 4-29 Lever Unit Pinch Ass’y, Plate Joint, Spring Pinch Drive Removal Toshiba 4-14...
Page 43
2) After reinstalling, check the bottom side of the Post #9 Guide to the top side of Main Base. "A" Œ SPRING #9 GUIDE ´ LEVER #9 GUIDE ASS`Y "B" Fig. 4-31 FE Head Removal Fig. 4-30 Lever #9 Guide Ass’y Removal 4-15 Toshiba...
Page 44
2) Remove the screw Œ. 3) Lift the ACE Head Ass’y ´. Œ SLIDER S ASS`Y Œ SCREW ´ SLIDER T ASS`Y ´ HEAD ACE ASS`Y Fig. 4-33 Slider S, T Ass’y Removal Fig. 4-32 ACE Head Removal Toshiba 4-16...
Page 45
1) Release the Hook Œ. 2) Lift the Lever Head Cleaner Ass’y ´. ´ LEVER HEAD CLEANER ASS'Y Œ HOOK SLEEVE-HEAD CLEANER ˇ CYLINDER ASS'Y Fig. 4-34 Plate Ground Deck, Cylinder Ass’y Removal Fig. 4-36 Level Head Cleaner Ass’y Removal 4-17 Toshiba...
Page 46
3) Rotate Gear Worm Œ clockwise using screw driver again up to the state of eject mode and then pick out the tape.(Refer to Fig. 4-38) ˇ MOTOR CAPSTAN ASS'Y Fig. 4-37 Damper Capstan,Motor Capstan Ass’y Removal FRAME Fig. 4-39 Toshiba 4-18...
Page 47
∆ CAPSTAN MOTOR PULLEY BELT PULLEY ∆ HOLDER CLUTCH ASS’Y GEAR CENTER ASS’Y GEAR IDLE (2Point) LOADING MOTOR BAND BRAKE ASS’Y BRAKE T ASS’Y ◆ : Add Oil ∆ : Cleaning O : Check and replacement in necessary 4-19 Toshiba...
Page 48
Disassembly and Reassembly MEMO Toshiba 4-20...
Page 49
5-1-1 Location of adjustment button of remote control EJECT STANDBY DISPLAY X-Point (Tracking Center) Adjustment I.SELECT COUNT.RST F.ADV INDEX COUNT/TR CLR/RST TIMER MENU NVRAM Option Setting PLAY CURSOR SLOW PAUSE /STILL STOP SP/ LP AUDIO TV/VIDEO Head Switching Adjustment A.DUB SAT.MONI. VT-701EG Fig. 5-1 Toshiba...
Page 50
Alignment and Adjustment 5-1-2 SW703 location for adjustment mode setting SW701 SW702 SW703 PRESS Fig. 5-2 Main PCB (Top View) Toshiba...
Page 51
Fig. 5-3 Location of Tape Transport Adjustment PINCH ROLLER FE HEAD CYLINDER ASS'Y GUIDE ROLLER "S" GUIDE ROLLER "T" POST TENSION #8 GUIDE POST #9 GUIDE POST #3 GUIDE POST MAIN BASE ACE HEAD CAPSTAN SHAFT Fig. 5-4 Tape Travel Diagram Toshiba...
Page 52
Test point : TP601 (Control Pulse) TP602 (H’D S/W -Trigger) TP301 (Envelope) TP302 (Audio output) TP303 (Video output) Test tape : ST-N1 BLANK TAPE : T-160 AUDIO OUTPUT ENVELOPE HEAD SWITCHING Fig. 5-5 Location of Test point (Main PCB-Top View) Toshiba...
Page 53
4) Connect the CH-1 probe to TP303 (Envelope) the CH-2 probe to TP601 (H’D switching pulse) and then trigger to CH-1. 5) Insert the (-) driver into the X-Point adjustment hole and adjust it so that envelope waveform is maximum. 6) Turn the Power off. Toshiba...
Page 54
) driver to obtain a flat video RF envelope as shown in Fig. 5-11. IDEAL ENVELOPE S HEIGHT TOO HIGH S HEIGHT TOO LOW T HEIGHT TOO HIGH T HEIGHT TOO LOW GUIDE ROLLER S GUIDE ROLLER T Fig. 5-11 Guide Roller S, T Height Adjustment Toshiba...
Page 55
3) Brake is operated by slider cam at FF/REW mode. 4) Transportation of accurate driving force is done by gears. (Gear Center Ass’y) Note : If the spec. does not meet the followings speci- fications, replace the holder clutch ass’y and then recheck. Toshiba...
Page 56
CNG : OK SAVE : MENU Fig. 5-14 Fig. 5-15 <Table 5-2> MODEL OPTION NUMBER V-621EW 6, 7, 8, 9, 10, 11, 13, 14, 15, 18, 20, 29, 30, 34, 35, 36, 38, 42, 45, 49, 50, 60, 61, 64 Toshiba...