1. Manuals
  2. Brands
  3. Spaw Manuals
  4. Welding System
  5. 210 Synergy MIG easy
  6. Manual

Spaw 210 Synergy MIG easy Manual

Inverter semi-automatic welding
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MANUAL inverter
semi-automatic WELDING
Model:
210 Synergy MIG easy
Drawings devices in the manual may differ from the original colors.
Original instructions.
with
NOTE: Please use a welder after a very careful reading the manual.
1. In order to ensure safety should be determined by qualified personnel responsible for installation,
maintenance, periodic inspection and repair equipment.
2. In order to ensure safety before working with the machine carefully and with full understanding
refer to the following instructions.
3. After reading the following instructions and keep it in a place accessible to other users of the
device.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 210 Synergy MIG easy and is the answer not in the manual?

Questions and answers

Related Manuals for Spaw 210 Synergy MIG easy

Summary of Contents for Spaw 210 Synergy MIG easy

  • Page 1 MANUAL inverter semi-automatic WELDING Model: 210 Synergy MIG easy Drawings devices in the manual may differ from the original colors. Original instructions. with NOTE: Please use a welder after a very careful reading the manual. 1. In order to ensure safety should be determined by qualified personnel responsible for installation, maintenance, periodic inspection and repair equipment.

  • Page 3: Table Of Contents

    Table of Contents 1. INTENDED USE ..........4 1. INTENDED USE ..........4 1. INTENDED USE ..........4 1. INTENDED USE ..........4 2. TECHNICAL DATA ................4 2. TECHNICAL DATA ................4 2. TECHNICAL DATA ................4 2.

  • Page 4: Intended Use

    The manufacturer is not liable for damages resulting from misuse. 2. TECHNICAL DATA 2. TECHNICAL DATA MODEL 210 Synergy MIG easy Power AC 230 [V], 50 [Hz] 6.4 [kVA] Power consumption max. required safety...

  • Page 5: Precautions For Use

    3. PRECAUTIONS FOR USE 3. PRECAUTIONS FOR USE Please read all safety regulations and all instructions. Failure to comply with Please read all safety regulations and all instructions. Failure to comply with safety regulations and instructions may result in electric shock, fire and / or serious injury.
  • Page 6 d) prepare adequate protection face and eyes, e) check the condition of the welding connections and the operating handle, check whether the execution of the welding does not endanger the environment (radiation curve, the possibility of ignition elements flammable) g) check whether in the case of welding on the wall, the other side can not occur inflammation, 3.3.
  • Page 7 d) Organize welding equipment. 3.6. Final remarks. a) When performing welding work inside the tanks, boilers or other confined spaces (to 15m3), a welder should be insured by another person, who will remain on the outside. ELECTRIC SHOCK CAN KILL: Welding apparatus produce a high voltage. Do not touch the torch or welding material ELECTRIC SHOCK CAN KILL: Welding apparatus produce a high voltage.

  • Page 8: Symbols

    4. SYMBOLS 4. SYMBOLS To reduce the possibility of injury, the user must first read all the instructions. General warning sign notes for each user on the general danger. It is combined with other instructions warning or other symbols that failure can lead to personal injury or equipment damage.

  • Page 9: Construction And Control Panel

    Function HOT START "hot start" is a temporary increase in the welding current over the set value at the moment of arc ignition. This prevents the phenomenon of "stick electrode" in the initial phase of the welding start the whole process easier.
  • Page 10 5. Cable with connector for the selection of polarization - the welding of MIG-MAG must be plugged into one of the slots according to the 5. Cable with connector for the selection of polarization - the welding of MIG-MAG must be plugged into one of the slots according to the selected polarization.
  • Page 11 4. Panel selection of wire diameter in synergy mode or welding without synergy with manual settings. 0.6; 0.8; 0.9; 1.0 - selection of wire diameter in synergy mode for the method MIGMAG. 0.6; 0.8; 0.9; 1.0 - selection of wire diameter in synergy mode for the method MIGMAG. Manual - MIG-MAG without synergies.

  • Page 12: Kit Contents

    8. Set display V - the current value of the welding voltage. V - the current value of the welding voltage. V +/- - matching the voltage value (ranging from -10 to V +/- - matching the voltage value (ranging from -10 to +10).

  • Page 13: Fitting Wire Welding - Mig / Mag

    The supply network should have a stable voltage. Cross-section of the supply lines should not be less than 2.5 mm. Devices which do not have power plugs connected by. tips listed below. Connecting and sharing the power cord and the plug should be made by a qualified electrician.

  • Page 14: Inserting The Wire Electrode

    aluminum, Teflon armor use. For the welding of low carbon steel, low alloy steel, copper, bronze, etc., Are used with spiral metal armor. It should be remembered accessories from the welding torch in the contact tip to the appropriate species and the filler wire diameter. 5.

  • Page 15: Connection Of Protective Gas

    7.4 Connection of protective gas. 1. The cylinder with a suitable protective gas should be set to a semi-automatic shelf (if present) or the wall 1. The cylinder with a suitable protective gas should be set to a semi-automatic shelf (if present) or the wall and prevent it from tipping over, securing it to the support by means of a chain.

  • Page 16: Practical Recommendations Mig / Mag Welding

    MIG 210 Synergy easy has the ability to manually set the parameters which takes place as in the case of traditional semi-automatic welding. To this end, the choice of diameter of the wire should be pressing the Start button, select 'Manual. " Then the wheel to set the wire feed speed - in the entire speed range.
  • Page 17 Excessive lengthening or shortening the arc can cause unstable arc glow and poor weld quality. L1, L2 - arc length The depth of penetration is also significantly impact the direction of welding - carrying the torch. H1, H2 - the depth of penetration The protective gas guards determines the efficiency of the welding area, but also of a process for transferring the metal in the arc, the welding speed and the shape of the weld.

  • Page 18: Welding Mma

    7.7 Welding MMA The device described in this guide is able to weld with coated electrodes hot melt. To weld MMA, select on the control panel function MMA. After selecting the MMA can immediately adjust the welding current. Adjustment is done by turning the knob.

  • Page 19: Tig Lift

    7.8 TIG LIFT The device described in this document can be applied to TIG welding LIFT. You will need to acquire the holder intended for this method - a handle provided with a mechanical protective gas valve arranged in the handle. In order to obtain high quality, convenience and economy TIG welding, we recommend purchasing a contactless arc ignition, brand MAGNUM series TIG TIG THF or VIPER.

  • Page 20: Cleaning And Maintenance

    8. CLEANING AND MAINTENANCE 8. CLEANING AND MAINTENANCE Degree of protection of this device is IP21S, so, do not use the unit in the rain, or expose it to moisture. ATTENTION: A device based on electronic components. Grinding and cutting in the vicinity of the welding device can contaminate the swarf inside the device, thus leading to damage.

  • Page 21: Interference At Work Welders

    9. INTERFERENCE AT WORK WELDERS 9. INTERFERENCE AT WORK WELDERS Cause Procedure symptoms Tighten the clamp correctly For poorly tightened pressure Contaminated guide wire holder Clean the guide wire electrode No feed of the electrode wire (feeder motor is Brought into line with the roll diameter of the A predetermined groove roll does not correspond to the running) wire...

  • Page 22: Warranty

    All records on the scope of the guarantee, the principles of its lending and other requirements are specified on the warranty card issued with the device. Warranty and post-warranty service: Spaw Company - Service 30-731 Kraków ul. Reapers 3 12 Tel .: 348-07-22...

  • Page 23: Statement Of Compliance

    13. STATEMENT OF COMPLIANCE The product complies with European Union with...

Table of Contents