Advertisement
We congratulate you on your purchase of a Valentine Hot cupboard. This is
a high quality product renowned throughout Europe for over 50 years.
The instructions below take into account new legislation concerning product
liability as well as EU and international safety standards.
Important note:
Before using your hot cupboard, please make sure you observe the following:
⇒ study and strictly follow the instructions given below
⇒ notify personnel on how to use the hot cupboard correctly and draw their attention to in-
herent risks
Valentine Fabrique SA disclaims any liability for damage or injury caused by incorrect use of
the hot cupboard and failure to comply with the operating instructions
• Beware of burns!
Inherent risks
• Take care when touching the upper and lower parts of the table or the
heating shelves, which can reach 100
• Set the thermostat at 60
• Do not sit on or upon the hot cupboard!
1
Hot table signal lamp
2
Hot table thermostat
3
Upper compartment signal lamp(
4
Upper compartment thermostat
5
Lower compartment signal lamp
6
Lower compartment thermostat
7
On / OFF signal lamp
8
Switch
9
Hinged shelf, lift to clean base
Installation: The hot cupboard must be connected to a one-phase 3-pins plug with earth
connection, voltage 230 V~ [10]
0
C
0
C maximum
10
Connecting lead - 1,9 m
11
Lower guide rails
12
Door rails and bearings
13
Hot table top
14
Lower compartment
15
Upper compartment
16
Hot table
17
Front sliding door on bearing
18
Back sliding door on bearing
Earth: yellow / green
Neutral: blue
Use of V40-90 and V42-90: The hot cupboards V40-90 and V42-90 are divided into 3 inde-
pendent parts, each with its own thermostat, that is: the lower compartment [14], the upper com-
partment [15] and the hot table [16].
Switch on main switch [8]
Turn the thermostat [4] to «60» if necessary the thermostat
[6] and the thermostat [2] during use
Always shut the doors com-
pletely
Never overheat.
otherwise
o
Set the thermostat of 60
C
maximum
The plates are made of on isolating material and the heat will take approximately 1 hour to pene-
trate to the centre of the plate. A plate which is heated too quickly is only hot on the surface and
will cool very quickly.
Cleaning: The interior must be kept very clean. Disconnect the apparatus and clean with a
damp cloth. To clean the box, lift the hinged shelf [9]. Never splash water into
the apparatus.
Technical specifications:
Model:
Rating
[kW]
Conn. 230 V
[A]
Frequency
[Hz]
Capacity of 27 cm ø plates
Capacity of 30 cm ø plates
Capacity of 32 cm ø plates
Capacity of 33 cm ø plates
Heating
Leaktightness
Weight
[kg]
900 / 400 / 850
External dimensions
[mm]
Internal dimensions
[mm]
2 x (820 / 325 / 310) 2 x (820 / 335 / 310)
Troubleshooting:
Faults
Probable cause
∗ No power
Main switch and / or a thermostat
switched on: one of the signal
lamps does not light up
∗ Faulty bulb
Thermostat switched on: the signal
lamp does not light up
∗ Faulty heating element
Main switch and thermostat
switched on: the cupboard does not
heat
∗ Door derailed
The door do not slide freely
The lamp [7] lights up
⇒
The lamp [3], [5] and [1] lights up
⇒
Pre-heating of plates = 1 to 1½ h.
⇒
• An open door lets all the heat es-
cape
• The plates will cool down even with
the heating switched on
V 40-90
V 42-90
1,5
1,5
6,5
6,5
50 - 60
50 - 60
150
150
100
100
100
100
---
100
on 3 levels
on 3 levels
IP X5
IP X5
61
62
900 / 420 / 850
Solutions
◊ Check fuses, plug and socket
carefully
◊ Change bulb if other lamps work
◊ Change bulb
◊ Call After-Sales Service
◊ Dismount the table [13] in order
to reach the bearings. Remove
the screws of the top back edge,
lift the top and push forward
Interrupteur
thermostat
gnaux lumin
Thermostat
lumineux ne
Interrupteur
enclenché:
Les portes
Advertisement
