Page 1
website:http://biz.LGservice.com e-mail:http://www.LGEservice.com/techsup.html COLOR TV SERVICE MANUAL CHASSIS : MP-03AB MODEL : RE/RL-44/49/54NA14T CAUTION BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. TV/AV MENU MUTE ON/OFF...
SAFETY PRECAUTIONS IMPORT ANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service transistors and semicounductor "chip" components. The manual and its supplements and addenda, read and follow the following techniques should be used to help reduce the SAFETY PRECAUTIONS on page 3 of this publication. incidence of component damage caused by static by static NOTE: If unforeseen circumstances create conflict between the electricity.
Page 5
c. Qulckly move the soldering iron tip to the junction of the Fuse and Conventional Resistor component lead and the printed circuit foil, and hold it Removal/Replacement there only until the solder flows onto and around both the 1. Clip each fuse or resistor lead at top of the circuit board component lead and the foil.
5) Follow each drawing or spec for spec and performance of parts,based upon P/N of RPL 6) Warm up TV set for more than 60min before the measurement. Test and Inspection Method 1) Performance : Follow the Standard of LG TV test 2) Extra requirement Model...
Page 7
Test and Inspection Method (S Mark : Option Item) Item Specification Remark Recieving System PAL, SECAM-BG PAL, SECAM-DK, PAL-I PAL, SECAM-BG SECAM-LL’ AV can be input NTSC-M PAL, SECAM-BG, PAL, SECAM-DK, PAL-I NTSC-M Available Channel 1) VHF : E2 ~ E12 2) UHF : E21 ~ E69 3) CATV...
Page 8
Feature and Function Item Remark Specification Feature AV Input Side V/L/R S (Rear, RT model) V/L/R AV Output S (Rear, RT model) V/L/R Component Input COMPONENT1, L/R Rear 480i/ 480P/ 576i (1080i for CHINA) COMPONENT2, L/R S-Video Input side 1, Rear 1 SCART S (Rear, RE,RL model) Full SCART (with RGB Input) : 1...
8. PSM (Picture Status Memory) recalls your preferred picture setting. 9. SLEEP sets the sleep timer. 10. I/II selects the language during dual language broadcast. selects the sound output (option). 11. VCR BUTTONS control a LG video cassette recorder. (With TELETEXT/PIP) - 9 -...
Page 10
12. MULTIMEDIA selects Component 1 or Component 2 modes. switches the set on from standby. 13. TURBO PICTURE BUTTON selects Turbo picture. 14. TELETEXT BUTTONS (option) POWER These buttons are used for teletext. For further details, see the ‘Teletext’ section. TV/AV MULTIMEDIA TURBO...
Page 11
Front panel • RE/RL-44/49/54NA13/14 series TV/AV MENU MUTE TV/AV MENU MUTE ON/OFF (Side panel) • RE/RL-39NZ43 series TV/AV MENU INDEX TV/AV MENU INDEX 7 6 5 9 • RE/RL-44/49/54NZ23 series TV/AV MENU TV/AV MENU • RE/RL-44/54NA23/24 series • RE/RL-44/54NA43/44 series MUTE MENU MUTE...
Page 12
Front panel • RE/RL-40/45/57NZ60 series TV/AV MENU MUTE TV/AV MENU MUTE (Side panel) 1. MAIN POWER (ON/OFF) 10. LED (Light Emitting Diode) DISPLAY switches the set on or off. (option) illuminates brightly when the set is switched (Volume Up/Down) adjusts the volume. Option : Only RE/RL-39NZ43 series, adjusts menu settings.
ADJUSTMENT INSTRUCTIONS These instructions are applied to only MP-03AB chassis. Notes 1.Because this is not a hot chassis, it is not necessary to use an isolation transformer. However, the use of isolation transformer will help protect Green Light test instrument. Red/Blue Light 2.Adjustment must be done in the correct order.
Page 14
(2) Adjustment must be operated in a dark room (simple dark 2 Pole Magnet room) 2. Adjustment 4 Pole Magnet (1) Test Equipment: Oscilloscope, 100:1 Probe (2) Connect oscilloscope to cathode of R, G, B(R926R/B/G: SCREEN ADJ on the PCB) and GND. 6 Pole Magnet (3) Turning Screen Volume (R/G/B) in Focus Pack and adjust R/G/B is 165V!0.5V.
Page 15
6) ET(East-west Trapezium) Fifth Vertical Line Fifth Vertical Line Adjust to make the width of top horizontal line same with it of the bottom horizontal line. Third Bar Third Bar 4. 1080i Mode deflection Adjustment (option) Sixth Vertical Line (1) Test Equipment 7) A-ANG(AFC Angle) SETTOP BOX with 1080i output Vertical slope adjustment...
Page 16
8) PIN PH : Horizontal Trapezoid Fixation Lens Change of chromatic aberration Adjust the horizontal width of screen upper and lower is Orange ¤AScarlet to be same. Green Blue ¤ARed 9) PIN AM : Horizontal PARABOLA Correction CHROMATIC Blue Purple ¤AGreen ABERRATION Adjust the vertical line of most angle lattice of right/ left CROSS HATCH...
Page 17
5. Focus checking 4) Quit pattern shift mode. (Press “OK” button) 5) Save adjusted phase/pattern position adjustment After adjustment Red,Green & Blue lens, remove lens cover mode.(Press “9”, “2” & “OK” buttons) and receive Cross-Hatch pattern and check the overall focus. If needed,repeat above.
Page 18
4) Receive WINDOW signal. Check the Option Adjustment * High Light : 1) Check the OPTION1~5 data of attach 6 is well recorded. RE/RL : 250!10 (16:9) cd/m^2 2) The option value of each suffix is started on JOB EXP of : 160!10 (16:9) cd/m^2...
Page 19
Convergence Adjustment Mode - INSTART -> 3 -> MENU * This Mode is for engineering. So,don’t change before permission from Design Department. 0.AC POSITION READ : Distance data(After auto convergence measuring) 1.Save to 50Hz/60Hz : Save (convergence adjustment data) It’s same 9,1,Enter. 2.Save Control data : Save (A phase adjustment data) It’s same 9,2,Enter.
Page 20
8.OSD POSITION 2. Sound adjustment data (IC:MSP3411G) 9.AC PATTERN ADJ :Assign location for pattern start Menu Description Range Default <NTSC mode> <PAL mode> FM Prescaler NICAM Prescaler SCART Prescaler 8,17 17,16 5,17 10,33 14,30 S1 VOL SCART 1 Volume 17,15 10,15 3,15 12,31...
Page 21
3.Picture adjustment data(IC:CXA21801) Menu Description Range D-COL Dynamic color mode setting EXTSW Selects the Y/Cb/Cr input or EY/ECb/Ecr SHPFO Sharpness f0 setting BLKBT RGB output bottom limiter level control (for blanking/signal) PREOV Pre-shoot/over-shoot ratio setting CTILE CTI level setting LTILE LTI level setting PLMTL RGB output amplitude level setiing...
Page 22
4.Picture adjustment data (IC:CXA21802) Menu Description Range R-Y R R-Y axis + (R-Y) component setting R-Y B R-Y axis + (B-Y) component setting G-Y R G-Y axis + (R-Y) component setting G-Y B G-Y axis + (B-Y) component setting UP-BL VBLK position control for top of picture, when VBLK_SW = 1 LO-BL VBLK position control for bottom of picture, when VBLK_SW=1...
Page 23
5.CXA2151Q adjustment item Menu Description Range INPUT Selects the four systems of inputs IN1 to IN4 MAT-O Selects the type of matrix conversion VFREQ Selects the frequency of the dummy sync output to SELV_OUT(pin23) SELS1 Selects the type of the signal input to IN1_H/L1(pin36) and IN1_V/L2(pin37) SELS2 Selects the type of the signal input to IN1_H/L1(pin44) and IN1_V/L2(pin45) FIX-S...
Page 24
6. OPTION Data Adjustment Option 1 Item Specification Remark 200PR 1 : 200 PROGRAM (CHINA ONLY) 1 : LIST no operation 0 : 100 PROGRAM (OTHER CONTRIES) 0 : LIST operation TSEAR 1 : WITH TURBO SEARCH 1 : RT/ RE 0 : WITHOUT TURBO SEARCH (FRANCE) 2 ;...
Page 25
Option 3 Item Specification Remark 1 : WITH PIP 0 : WITHOUT PIP INDEX 1 : WITH INDEX 0 : WITHOUT INDEX HDEV 1 : HIGH DEVIATION MODULATION (CHINA) 1 : China/ Saudi/ Indo/ Indonesia 0 : RF NORMAL SOUND MODULATION (OTHERS) D - PRO 1 : WITH DOLBY PRO LOGIC 0 : WITHOUT DOLBY PRO LOGIC...
Page 26
Option 5 State Language Function LANGUEGE 0:ENG Only English 1:EU 5EA English/German/French/Italy/Spanish 2:EU ETC Pol./Hungary/Czecho/Russia/Eng English/ Greece 3:GREECE 4:PARSI English/Parsi (Iran) 5:ARAB URDU English/French/Arab+Urdu T-LAN 6:English+Hindi English/Hindi 7:English+I+M+V English/Indonesian/Malaysian/Vietnamese 8:English+THAI English/Thai 9:English+China English/China English/French/Swedish/Czech/German/Spanish/Italian 0:West Europe 1:East Europe Polish/French/Swedish/Czech/German/Slovenian/Italian/Rumanian 2:Turkey EU English/French/Swedish/Turkish/German/Spanish/Italian 3:EAST EU2 English/Hungarian/Serbian/Czech/German/Polish/Spanish/Italian/...
Page 49
LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION Q2201 0TR387500AA TR, CHIP 2SC3875S(ALY) KEC Q432 0TR126609AA TR, KTA1266-Y(KTA1015) KEC TP TO92 50V 150MA Q2202 0TR150400BA TR, CHIP 2SA1504S(ASY) KEC Q500 0TR387500AA TR, CHIP 2SC3875S(ALY) KEC Q2203 0TR387500AA TR, CHIP 2SC3875S(ALY) KEC Q501 0TR150400BA TR, CHIP 2SA1504S(ASY) KEC...
Page 50
LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION Q902G 0TR319809AA TR, KTC3198(KTC1815) KEC TP TO92 50V 150MA D603 0DS113379BA DIODE, 1SS133 T-72 TP ROHM KOREA DO34 90V Q902R 0TR319809AA TR, KTC3198(KTC1815) KEC TP TO92 50V 150MA D604 0DS113379BA DIODE, 1SS133 T-72 TP ROHM KOREA DO34 90V Q905G 0TR126609AA...
Page 51
For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film digit in the P/No. means as CE : Electrolytic RN : Metal Film follows;...
Page 52
For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film digit in the P/No. means as CE : Electrolytic RN : Metal Film follows;...
Page 53
For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film digit in the P/No. means as CE : Electrolytic RN : Metal Film follows;...
Page 54
For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film digit in the P/No. means as CE : Electrolytic RN : Metal Film follows;...
Page 55
For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film digit in the P/No. means as CE : Electrolytic RN : Metal Film follows;...
Page 56
For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film digit in the P/No. means as CE : Electrolytic RN : Metal Film follows;...
Page 59
For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film digit in the P/No. means as CE : Electrolytic RN : Metal Film follows;...
Page 60
For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film digit in the P/No. means as CE : Electrolytic RN : Metal Film follows;...
Page 61
SWITCH, POWER SDDF3PASP013 LG C&D UL/C R919B 0RD6201F609 6.2K OHM 1/6 W 5.00% TA52 SWT01 140-313B SWITCH, TACT 2LEAD 160G(TA) LG C&D NON R919G 0RD6201F609 6.2K OHM 1/6 W 5.00% TA52 SWT02 140-313B SWITCH, TACT 2LEAD 160G(TA) LG C&D NON...
Page 62
LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION FB2005 125-022K FILTER,EMC FERRITE 1UH TAPING L2021 6210TCT002B FILTER,EMC ACB2012M-300-T TDK , CHIP BEAD,LCD FB2006 125-022K FILTER,EMC FERRITE 1UH TAPING L2027 125-022K FILTER,EMC FERRITE 1UH TAPING FB2007 125-022K FILTER,EMC FERRITE 1UH TAPING L2028 6210TCT002B FILTER,EMC ACB2012M-300-T TDK , CHIP BEAD,LCD...
Page 63
JACK,RCA PPJ125C 2X5 10PIN,COMPO-6,AD-4 ACCESSORIES 3828VA0408B MANUAL,OWNERS MP03AB DG/BN/ 100R/U TX 016C 026C 3828VA0408C MANUAL,OWNERS MP03AB HS LG GR 100R/U TX 050A 3828VA0408F MANUAL,OWNERS MP03AB IS/REG LG IT 100R/U TX 3828VA0408J MANUAL,OWNERS MP03AB FS LG FR 100R/U TX 335A 6710V00100U...