Related Manuals for powersoft MiniMod 4
Summary of Contents for powersoft MiniMod 4
- Page 1 MiniMod 4 USER GUIDE ©2021 Powersoft Keep this manual DO000243.00 Rev. 02 for future reference...
- Page 2 Data are subject to change without notice. For latest update please refer to the online version available on www.powersoft-audio.com.
-
Page 3: Table Of Contents
Table of contents 1. Important safety instructions 12 : 1.3. Primary thermal protection 2. Importantes instructions de sécurité 12 : 1.4. Auxiliary Undervoltage Protection 3. Instrucciones de seguridad importantes 12 : 2.Amplifier protections 4. Importanti istruzioni di sicurezza 12 : 2.1. Amplifier Thermal protection 5. - Page 4 Page intentionally left blank ii | MiniMod 4 | User guide...
-
Page 5: Important Safety Instructions
8. Do not defeat the safety purpose of the polarized or grounding- DO NOT USE THE UNIT AT ALTITUDES ABOVE 2000 M. type plug. 9. Only use attachments/accessories specified by Powersoft. DO NOT USE THE UNIT IN TROPICAL ENVIRONMENT. 10. Refer all servicing to qualified service personnel. Servicing is... -
Page 6: Importantes Instructions De Sécurité
CONTACTER LE CENTRE DE SERVICE AUTORISE POUR UN ENTRETIEN ORDINAIRE ET EXTRAORDINAIRE. IL EST ABSOLUMENT NÉCESSAIRE DE VÉRIFIER CES CONDITIONS FONDAMENTALES DE SÉCURITÉ ET, EN CAS DE DOUTE, D'OBTENIR UNE VÉRIFICATION PRÉCISE PAR DU PERSONNEL QUALIFIÉ. iv | MiniMod 4 | User guide... -
Page 7: Instrucciones De Seguridad Importantes
EQUIPOS ELÉCTRICOS Y ELECTRÓNICOS (WEEE por sus siglas 6. No bloquee las aberturas de ventilación. Realice la instalación de en Inglés). acuerdo con las indicaciones de Powersoft. ENTRE 0°C Y +35°C +35° 7. No instale cerca ninguna fuente de calor como, por ejemplo, DEGRADACIÓN POR ENCIMA DE 35°C. -
Page 8: Importanti Istruzioni Di Sicurezza
CONTATTARE IL CENTRO DI ASSISTENZA AUTORIZZATO PER ESEGUIRE LA MANUTENZIONE ORDINARIA E STRAORDINARIA. E’ ASSOLUTAMENTE NECESSARIO CONTROLLARE QUESTI REQUISITI FONDAMENTALI SULLA SICUREZZA E, IN CASO DI DUBBI, RICHIEDERE UN CONTROLLO ACCURATO DA PERSONALE QUALIFICATO. vi | MiniMod 4 | User guide... -
Page 9: Regulatory Information
For compliance questions only: compliance@powersoft.it aims to minimise the impact of electrical and electronic goods on the en- vironment. Powersoft S.p.A. comply with the Directive 2002/96/EC and 2003/108/EC of the European Parliament on waste electrical finance the cost of treatment and recovery of electronic equipment (WEEE) in order to reduce the amount of WEEE that is being disposed of in land-fill site. -
Page 10: Electrostatic Discharge (Esd)
Electrostatic Discharge Sensitive devices (ESDS) and assemblies are handled outside of full static protection packaging (i.e. within static control areas) should be pro- vided with some form of ground conductive or dissipative flooring. viii | MiniMod 4 | User guide... -
Page 11: Minimod4 | 1
If you find any damage notify the safety instructions. In case you have any questions, please shipping company immediately. do not hesitate to contact your dealer or Powersoft. The MiniMod4 is a four channel amplifier modules spe- 7 : 3.Disposal of the packing material cifically designed to drive high power loudspeakers. -
Page 12: Thermal Constraints
Module in a separate Be aware of as the highest ambient temperature air leakage vented chamber. as the highest operating temperature 2 | MiniMod 4 | User guide... -
Page 13: Electromagnetic Compatibility (Emc) & Safety
9 : 5.Mains Fuse Parallel pair Configuration MiniMod 4 is equipped with an internal Time Delay prone to RF noise fuse rated at 4A. This fuse must be replaced only by an authorized Powersoft service center. Twisted pair Highly immune 9 : 6.Earth connection... -
Page 14: Mechanical Drawings
APPROV. TOLERAN UNI-ISO 17/05/2018 raveggi 1 / 1 2768-M 4 | MiniMod 4 | User guide WEIGHT POWERSOFT S.p.A. 0,0 kg PF000477 Via E.Conti, 5 - 50018 Scandicci (FI) - Italy DRAWING Tel. +39 055 7350230 - fax +39 055 7356235... -
Page 15: Connections
Connections PL2001 PL1001 PL3000 PL1000 11 : 1.Grounding 11 : 2.Bill of connectors The amplifier module is intended to be assembled in an CODE NAME TYPE End Product. PL1000 In the End Product, the metal plate of the amplifier module Input connector IDC socket 34 pin PL3000... -
Page 16: 2.1. Pl2 Pinout (B3P-Vh Jst)
22 +12/15VDC OUT +12V @ 0,8A or +15V @ 0,6A +/-10% section supply (same as pin 22) TEMPMON 0-5V See table 1 1kΩ NTC sensor tap output Channel 2 Output Current IOUT2MON 8,35A/V 4,7kΩ Monitor 6 | MiniMod 4 | User guide... - Page 17 Pin# Name IN OUT POWER Range Scale Factor Impedance Tolerance Description Level 1 (4.5V to 5V) not in Channel 2 & Channel 4 PROTECT 24 protection. Level 0 (0V to 0.5V) in 4,7kΩ Output Stage Protection Protection Monitor Channel 2 Output Voltage VOUT2MON 20V/V 4,5kΩ...
- Page 18 Channel 4 Positive IN 4 + output shorting pin 7 to GND. 9,4kΩ Balanced input. 26dB Input 8Vrms absolute max input. to Output Overall Gain Balanced: 0,705Vrms for full 9,4kΩ output. 8Vrms absolute max input. 8 | MiniMod 4 | User guide...
-
Page 19: 2.4. Pl1001, Pl2001 Pinout
Pin# Name IN OUT POWER Range Scale Factor Impedance Tolerance Description Ground +5Vdc out 20mA max current +5VDC OUT +/-5% available RESERVED Open Collector, high when output READY 4 1KΩ Channel 4 Ready stage is operative Active High, Logic input 3,3 to SDPWS 1kΩ... -
Page 20: 4.Internal Signal Path Polarity
In order to increase the power’s supply energy storage efficiency, signals coming from channel pairs 1-2 are polar- MiniMod 4 can be configured in 5 different output type ity reversed, one with respect to the other within the pair, of connections: when entering the amplifier.
Need help?
Do you have a question about the MiniMod 4 and is the answer not in the manual?
Questions and answers