Page 2
DO000264.00_powersoft_LOTO_IK_UGuide_en Data are subject to change without notice. For latest update please refer to the online version available on www.powersoft-audio.com.
Table of contents 7 : 20.Connectors overview 1. Important safety instructions 7 : 20.1. Input Connectors 7 : 20.2. Output Connectors 2. Consignes de sécurité importantes 3. Importantes Instrucciones de Seguridad 4. Importanti istruzioni di sicurezza 5. Regulatory information 6. Electrostatic Discharge (ESD) viii 7. LOTO IK Assembly instructions 7 : 1.Introduction 7 : 2.Unpacking & Checking For Shipping Damage 1 7 : 3.Disposal Of The Packing Material 7 : 4.Programming the DSP 7 : 5.AC Main Filter...
Page 5
CLASS3 WIRING POWERSOFT SUGGESTS TO PLUG THE LOTO ASSEMBLY TO A 16 A RATING, exposed to rain or moisture, does not operate normally, or has C OR D CURVE, 10 KA SECTIONING BREAKER.
CLASS3 a été renversé ou des objets qui sont tombés dans l’appareil, si l’appareil a été POWERSOFT RECOMMANDE DE BRANCHER LA LOTO ASSEMBLY À UNE WIRING VALEUR DE 16 A, UNE COURBE C OR D, UN DISJONCTEUR SECTIONNEUR exposé...
CLASS3 POWERSOFT SUGIERE CONECTAR LA LOTO ASSEMBLY A UNA CURVA C O D WIRING expuesto a la lluvia o humedad, que no funcione normalmente o que este DE 16 A O A UN INTERRUPTOR DE SECCIONAMIENTO 10 KA.
è stato danneggiato in qualsiasi modo, come ad esempio se il CLASS3 cavo di alimentazione o la spina sono stati danneggiati, se è stato versato del POWERSOFT CONSIGLIA DI COLLEGARE LA LOTO ASSEMBLY A UN WIRING INTERRUTTORE DI SEZIONAMENTO DA 16 A, CURVE C O D, 10 KA.
Instead it is the user’s responsibility to dispose of their EN 62368-1: 2014 waste electrical and electronic equipment by handing it over to an approved reprocessor, or by returning it to Powersoft S.p.A. for reprocessing. For more information about where you can send Scandicci,...
6 Electrostatic Discharge (ESD) Electrostatic discharge (ESD) is one of the most significant factors leading to damage and failure of a wide variety of electronic components. Poor handling can cause internal damage, which is invisible. This internal damage can then cause electrical failure or reliability problems.
7 : 6.Earth Connection 7 : 8.Ferrite Cores Provide a mains voltage including the earth. The heatsink is Reject RF noise from input and output cabling by installing grounded. ferrite shields. Powersoft suggests the FAIR RITE 0431164181, or equivalent. LOTO Integration Kit Assembly instructions | 1...
Wrap both cables around one side of each ferrite so that it pass through each ferrite twice (ref. FIGURE 3). Install the ferrite shield as close as possible to where the cable plugs into the amplifier. Placing the ferrite elsewhere on the cable noticeably reduces its effectiveness.
7 : 11.Mechanical Drawings SE ST9 REV. DATE MATERIAL TREATMEN Shown here: LOTO Basic 2 (the dimensions are the same throughout the line) Tel. LOTO Integration Kit Assembly instructions | 3...
Place front panel on DSP LOTO IK ADV1D DSP assembly Screw the front panel to the related DSP assembly, by placing the (SMC01058.RD,) push it and band it under the retention clips of 5 screws (VI000112) with a screwing torque of 0,4Nm. XLR connectors up to finding its right position.
7 : 17.Front Panel Assembly – ADV2D Assemble the DSP card on the control panel Fix display by 4 screws (VI000289) with a screwing torque of 0,1Nm Rotate the assembly and insert the CN000790 e CN000791 cables on the display FR000004.R as in the picture CAUTION CAUTION CN000790...
7 : 18.Assembly of output connector board 7 : 19.Assembly of Amplifier Module Insert the O-rings (GU000104) Screw the module in place by using 6 screws M4x8 (VI000081) Insert the fan connector to the module as indicated by yellow circle in the picture, following the indicated path. Insert the mains voltage connector and the fan connector indicated by yellow circles in the picture.
Page 21
Insert the connector of external LED from SM001172.R into DSP Place the adhesive rubber foam as indicated. LOTO Assembly Insert the ribbon cables from DSP LOTO Assembly into the Litemod4HC Screw the front panel by placing the 5 screws M4X8 (VI000434) with a torque of 0,7Nm CAUTION CAUTION...
7 : 20.Connectors overview 7 : 20.1. Input Connectors ANALOG INPUT 1 + link OUT Balanced, +26dBu MAX input +/-15dB digital trim ANALOG INPUT 2 + link OUT Balanced, +26dBu MAX input +/-15dB digital trim AES3 INPUT + link OUT Active Link OUT w/ failover relay AES stream: +/-30dB digital trim 2x ETH+DANTE ports Switched ports...
Need help?
Do you have a question about the LOTO Series and is the answer not in the manual?
Questions and answers