Advertisement
Controls
Manual Controls
• The appliance can be operated manually
using the controls situated on the top right
hand side of the stove.
• On/off power switch – this is used to turn
the mains supply to the appliance on or off.
When the switch is in the ON position, the
orange stand by indicator light will show on
the top right corner of the screen. This switch
needs to be in the ON position to operate
manually or via the remote control / app.
• STAND BY - Used to switch the appliance to
Standby Mode
• FLAME - Pressing this button will allow you
to cycle through the 4 flame settings
• HEATER - Press this once to select low heat
Remote Control
Please note batteries are not included. 2 x AAA batteries are required.
(the indicator light will glow orange), twice to
select the high heat (the indicator light will
glow red), The indicator light will remain
visible for for approximately 7 seconds before
disappearing. Press the button for a third time
and the heater will turn off. The heater will
take approximately 30 seconds to slow down
and stop. Please note that the heater will only
operate when the room temperature is below
the temperature indicated on the remote
control handset. This can be altered via the
handset or via the app.
• MODE - The MODE button alters the flame
effect colour. The appliance has 16 different
flame effect colours that can be selected by
pressing the Mode button until you find the
option you prefer. Or alternatively you can
press and hold the Mode button for 4
seconds and it will then run through the
selection of preprogramed sequences.
• Remove the battery/control panel
cover by sliding completely down
and insert 2 x AAA batteries
ensuring these are inserted
correctly. Slide the cover back up to
the original position to refit. Old
batteries should be disposed of
responsibly at a local recycling
location.
• Ensure that the ON/OFF power
switch on the unit is in the ON
position.
• Aim the remote control handset
directly towards the fire and press
the function button required.
• Sliding the door down on the
remote control will reveal more
functions. Otherwise using the
basic remote control buttons will
operate the fire in the same way as
the manual control buttons.
6
SETTING THE COLOUR FUNCTIONS
• Press the lamp button
• Lamp 1 is for the rear flame
• Lamp 2 is for the base effect
• Lamp 3 is for the log effect
By pressing the lamp buttons, this will change
the colour of the rear flame, base effect and the
log effect separately.
SETTING THE TIME
• Press the CLOCK SETTING button which will
start the DAY curser to blink. Using the
CLOCK UP and CLOCK DOWN buttons to
set the current day e.g. 1-Monday, 2-Tuesday
etc and press CLOCK SETTING to confirm
the required day.
•The hour setting will now be blinking. Adjust
this by using the CLOCK UP and CLOCK
DOWN to reach the present hour and confirm
by pressing CLOCK SETTING.
•The minute setting will now be blinking. Adjust
as per the hour setting.
App Installation and Smart Control
• Your smart phone / tablet must be
connected to WIFI and the stove plugged
in.
• Use the POWER SWITCH and an orange dot
should appear on the fire screen. Do not use
the STAND BY button to switch this on.
• Scan the QR code and
download the ACR
Stoves app
• Open the app and click
the SIGN UP button. If
you already have this
App installed for other
ACR electric products
then please log in using your existing details.
The App can be used to operate multiple
ACR electric products.
• Input your email address and the App will
send a verification code to your email
address.
• Input the code to create your password.
• Press the Add Device button to add your
device.
ADJUSTING THE TEMPERATURE
While the stove is switched on, use
TEMPERATURE UP and TEMPERATURE
DOWN to set the required room temperature. A
confirmation beep will be audible from the fire.
If the room temperature is already warmer than
the temperature set on the remote control, the
heater will switch off / not come on until the
temperature in the room drops to below that on
the remote control.
ADAPTIVE CONTROL
This works in conjunction with the timer
programme. When Adaptive Control mode is
selected and turned on the fire monitors the
room temperature in relation to the selected
target temperature. If the room temperature is
lower than the selected temperature, the
Adaptive Control facility will instruct the fire to
switch on between 2 to 5 minutes earlier than
the set time this is to ensure that the room is at
the required temperate at the time selected
(please note this may not be possible to
achieve if the room is very large or very cold).
7
Advertisement
