Tacx Satori Smart T2400 Quick Start Guide

Tacx Satori Smart T2400 Quick Start Guide

Advertisement

Tacx Satori Smart T2400 Quick Start Guide

Assembling Satori Smart

  1. Check if everything is in the package
  2. Unfold the trainer and place it on a firm, level surface
    Unfold the trainer and place it on a firm, level surface
  3. Determine the position of the resistance unit
Position Wheeldiameter

1

2

650 - 700

600 - 650

Race / ATB 29"

ATB 26"

  1. Secure the resistance unit on the frame
    Secure the resistance unit on the frame
  2. Replace the blockage and put 6-8 bars in your tyre
    Replace the blockage and put 6-8 bars in your tyre
  3. Ensure that the cylinder presses firmly against the bicycle tyre
    Ensure that the cylinder presses firmly against the bicycle tyre
  4. Measure the diameter of the handlebars. Insert inlay for your handlebar diameter
    Measure the diameter of the handlebars
  5. Press the power switch to activate the trainer. Power off: automatically after 20 minutes or press power switch for 5 seconds
    Activate the trainer / Power off
  6. Calibration mode is activated automatically when powered on or is activated from the app
LED blinks ACTION
1 x per second Speed up to: 40 km/h
4 x per second Stop cycling: 0 km/h
2 x per second Finished

Specifications

Wireless Protocol: Bluetooth 4.0 & ANT+
Frequency 2,4Ghz
RF Output Power 6 dBm (typical)
Power supply 2x AA alkaline 1.5V, AA/LR6/UN-3
Temperature Range Operational -20°C to + 55°C
Transmit Range 10 m

FCC and IC Declarations

Your device contains a low power transmitter. When device is transmitting it sends out Radio Frequency (RF) signals.

Compliance statement (part 15)
This device complies with Part 15 of the FCC Rules and to the licence -exempt RSS standards(s) of Industry Canada. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

Warning (part 15.21)
Changes or modifications not expressly approved by the partly responsible for compliance could void the user's authority to operate the equipment.

RF Exposure
In order to maintain compliance with the FCC and RF exposure guidelines, this equipment should be installed and operated with minimum distance of 20cm between the radiator and your body. Unauthorized modification, or attachments could damage the transmitter and may violate FCC regulations

CE Declaration of Conformity
Tacx bv hereby declares that the this Satorti Smart (T2400) conforms to the essential requirements requirements set out in the Council (European parliament) Directive and other relevant provisions of directive 2004/108/EG, 2006/95/EG, 99/5/EG en 2011/65/EG RoHS. A copy of this decleration is available on the Tacx website: www.tacx.com

ROHS
This product is marked with this symbol. It means that used electrical and electronic products should not be mixed with general household waste. There is a separate collections system for these products.


Read complete user guide http://www.tacx.com/en/service/manuals

  • The rear wheel of the bicycle rotates at high speed whilst the trainer is in use.
  • Tests have revealed that the unit will not overheat, even when subject to extreme use. However, when subject to prolonged and intensive use, the enclosure around the brake may become very hot. Always allow the brake to cool down after use before touching it.
  • Always remove the cylinder from the bicycle tyre when the trainer is not in use.
  • Never brake abruptly when training. When braking the rear wheel, the flywheel continues to rotate which may cause unnecessary wear to the cylinder and the rear tyre.
  • Ensure not to drop the brake during assembly as this can lead to an imbalance which may cause vibration.
  • Never open the brake unit as this may cause damage.
  • Inspect the nuts and bolts on the trainer on a regular basis, and retighten if necessary.
  • Perspiration moisture and condensation can harm the electronics. Do not use the trainer in damp areas. Incorrect use and/or maintenance will void the warranty.
  • The Tacx trainer is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.
  • Children being supervised are not to play with the Tacx trainer.
  • This device is not designed for industrial, commercial or medical applications.
  • Do not expose the product to water or moisture.
  • Clean only with a dry cloth. Do not use cleaning solvents or abrasives.

Guide to safety and effective use

  • Before exercising with this device, please consult your physician or coach.
  • Do not use this device around medical equipment.
  • The wireless signal could be disturbed under the environment of high voltage or strong magnetic fields.

General

  • Designs and specifications are subject to change without notice.
  • All logos brands and product names are trademarks or registered trademarks of their respective holders and are hereby recognized as such.
  • This manual was produced with care. However no rights can be derived. Tacx cannot accept liability for any errors in this manual or their consequences.
  • Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
  • Keep this manual and packaging for future reference.

Videos

Tacx Satori Smart T2400 Review Video

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Tacx Satori Smart T2400 Quick Start Guide

Advertisement

Need Assistance?

Do you have a question about the Satori Smart that isn't answered in the manual? Leave your question here.

Error while submitting your question. Please, reload page and try again.

Thank you! Your question has been received!

Table of Contents