Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Weldclass Manuals
  4. Welding Accessories
  5. Promax 600 Series
  6. Operating manual

Weldclass Promax 600 Series Operating Manual

Electronic welding helmets
Hide thumbs

Advertisement

Quick Links

Download this manual
OPERATING MANUAL FOR
Promax 600 Series
ELECTRONIC WELDING HELMETS

Advertisement

loading

Summary of Contents for Weldclass Promax 600 Series

  • Page 1 OPERATING MANUAL FOR Promax 600 Series ELECTRONIC WELDING HELMETS...

  • Page 2: Table Of Contents

    Stop welding immediately if the helmet filter/lens fails to darken when the arc is struck. Do not continue use until the malfunction has been rectified. Read this manual for further information and if in doubt, return the helmet to your Weldclass distributor for further inspection.

  • Page 3: Specifications

    114x90 mm ADF/Cassette Dimensions 145x105x26mm Magnification Lens Holder Internal – takes standard 108x51mm magnifications lenses Standards Compliance - Shell AS/NZS1337.1 High Impact Standards Compliance – Auto AS 1338.1, ISO 16321-2, ANSI Z87.1, CSA Z94.3 Darkening Filter/Lens © Weldclass 2022. E.&O.E.

  • Page 4: Auto-Darkening Filter/Lens (Adf) Controls & Features

    Grind Mode locks the ADF to “off” (Shade 3). If helmet has eternal grind button, holding this for 3 sec will also turn grind mode on or off. Cut Mode locks the ADF to the set shade level. d. BATTERY LEVEL INDICATOR © Weldclass 2022. E.&O.E.
  • Page 5 Memory Setting. The Number represents the Memory number slot you are saving to or recalling. Use the Up and Down buttons to scroll through the memory Slots. Wait for 5 seconds after selecting the desired memory slot to save or recall these settings. © Weldclass 2022. E.&O.E.

  • Page 6: Replacing Accessories & Making Adjustments

    NOTE: If you have the mag lens holders installed, you may need to remove the whole cassette first. (see instructions in a Replacing Batteries) IMPORTANT: Use only original Weldclass cover lenses to ensure correct fit and conformance to safety standards. © Weldclass 2022. E.&O.E.
  • Page 7 Horizontal Position (Z): Adjusts the distance of the helmet from the operator’s face. Loosen the headgear retaining nut to change position (front, centre or rear). The same position should be selected on both sides. © Weldclass 2022. E.&O.E.
  • Page 8 Auto-Darkening Filter Cassette (ADF) Promax 650 WC-05349 Inner Clear Cover Lens Pkt 5 WC-05350 Sweat Band Pkt 5 WC-01630 Headgear Assembly WC-05353 Battery (CR2450) (Not pictured) WC-02640 Magnification Lens 1.5x P7-ML15 Magnification Lens 2.0x P7-ML20 Magnification Lens 2.5x P7-ML25 © Weldclass 2022. E.&O.E.

  • Page 9: Maintenance

    Reduce the ambient light level in Filter lens is dark when no arc The ambient light level is too bright the area is present or stays dark after the weld is extinguished Sensitivity too high Reduce sensitivity level © Weldclass 2022. E.&O.E.

  • Page 10: Warranty

    8. The cost of freight involved in transporting parts in the event of a warranty claim. This is a repair and/or replacement warranty only and does not allow for a refund. Weldclass reserves the right to replace faulty units covered under warranty with alternative / equivalent units should the original unit become obsolete or unavailable.
  • Page 11 © Weldclass 2022. E.&O.E.
  • Page 12 www.weldclass.com.au...

This manual is also suitable for:

Promax 650