Subscribe to Our Youtube Channel
Summary of Contents for Veigel eSlider
- Page 1 Rehamotive Installation and Operating Instructions eSlider Electrical 8-way transfer seat console Left-hand drive Art. no.: S10003 Right-hand drive Art. no.: S10005 www.veigel-automotive.de...
- Page 2 Document no. 250610 Created 2021-10-04 Name Schulz Subject to technical modifications without prior Revised 2022-01-26 notification and to errors. Reproduction, even in part, only permitted with Version 2 permission from Veigel GmbH + Co. KG.
-
Page 3: Table Of Contents
Tightening torques ....................5-1 Assembling the eSlider ..................5-2 Assembling the VEC control unit - eSlider ............5-3 Overview of plug connections on the VEC control unit - eSlider ......5-4 Assembling the control unit ................. 5-5 Adjusting the control unit ..................5-6 Checking the function .................. -
Page 4: Contents
Contents Revision history Edition Revisions Chapter 01 / 2021-10-04 Initial version 02 / 2014-03-26 Tilt graphic updated... -
Page 5: Symbols Used
This symbol indicates a risk of injury and crushing. Individual images contained in these instructions may deviate from the driving aid you received. Veigel hotline Veigel GmbH + Co. KG Telephone: +49 (0) 7941 60585-0 Verrenberger Weg 36 Fax: +49 (0) 7941 60585-20 74613 Öhringen, Germany... - Page 6 Contents Blank page for your notes...
-
Page 7: General Information
• The complete operating and installation instructions must always be carried in the vehicle. Intended use • This eSlider is only suitable for use in the named vehicle types; it may only be installed in these vehicle types. • The eSlider replaces an original seat without a lateral airbag. -
Page 8: Foreseeable Misuse
Safety information Foreseeable misuse • The red markings indicate the risk of injury when moving the eSlider. • It is not permitted to operate the eSlider while driving. • On the whole, private individuals are not permitted to store airbags. -
Page 9: Product Description
The Veigel eSlider is a fully-electric transfer seat console. Besides the 6 main dir- ections (forwards-backwards, up-down, right turn-left turn), the 6+2-way version also offers a tilt seat adjustment function. This offers a great advantage when sitting in the vehicle to improve lateral support, avoid bruising and lift the feet off the floor when transferring from the vehicle seat to the wheelchair and vice versa. -
Page 10: Scope Of Delivery - 8-Way Eslider
Product description Scope of delivery - 8-way eSlider Seat attach- ment to Lift unit lift unit Lift unit trim Swivel unit panel Linear unit Footrest Seat at- tachment to Linear unit front vehicle trim panel Lift unit trim panel Linear unit rear... -
Page 11: Scope Of Delivery - Vec Control Unit - Eslider
Product description Scope of delivery - VEC control unit - eSlider Clamp 30 Ground CAN high CAN BUS / vehicle side CAN low... - Page 12 Product description Structure of the 8-way eSlider Lift unit Swivel unit Linear unit...
- Page 13 Product description Movement range of lift and linear unit 207 mm 677 mm Movement range of linear unit = 119 mm 310 mm 1292 mm Movement range of linear unit = 615 mm...
- Page 14 Product description Swivel range 120° swivel position Drive position of Swivel unit...
- Page 15 Product description Tilt seat 10° Front tilt seat 10° Rear tilt seat...
- Page 16 Product description...
-
Page 17: Operation
• Keep the type approval, the installation and operating instructions, and the vehicle documents together inside the vehicle. • When the eSlider is installed, it replaces the original seat with airbag. The lat- eral airbag on the passenger side will be deactivated. -
Page 18: Functions Of The Control Unit Buttons
Operation Functions of the control unit buttons Forwards- Tilt Height Turn backwards Save Figure 4-1: Functions of the control unit buttons Button Assignment Tilt Tilt seat setting Height Up-down Turn Turn right-turn left Forwards- backwards Transfer forwards-backwards Save Saves the movement range... -
Page 19: Activating The Memory Function
Figure 4-2: Activating the memory function All drive positions up to their stop position If the eSlider control unit is being used for the first time, make sure to carry out the steps below. The same applies after disconnecting the supply voltage:... -
Page 20: Operating The Memory Function
Operation Operating the memory function Saving the drive position Move the eSlider by hand to the position which you want to save. Push the tilt setting switch back while at the same time pushing the memory switch forwards. You only need to press the switch briefly in order to save the position. -
Page 21: Using The Memory Function
Operation Using the memory function Push the memory function switch forwards and hold it there in order to move to the drive position. The drive position is always: Linear unit: Moved fully to the front Swivel unit: Turned fully to the inside Lift unit: Saved position Figure 4-5: Operating the memory function... -
Page 22: Linear Unit Emergency Release Mechanism
Operation Linear unit emergency release mechanism Left emergency release mechanism art. no.: S10003 Pull on the strap and pull out the button Keep hold of the button and press it until you reach the desired po- sition. Figure 4-7: Left emergency release mech- anism Right emergency release mechanism art. - Page 23 When delivered, the backup battery is not connected in order not to discharge it. Before the eSlider can be put into operation, the backup battery must be connected . To do this, connect the black cable to the cable set.
-
Page 24: Assembly
• Please read these operating instructions carefully before installing the eSlider. • Pass the operating instructions on to the customer, together with the installa- tion instructions for the eSlider and any parts certificate, when you hand over the vehicle. • Observe the applicable accident prevention and safety provisions when install- ing and maintaining the eSlider. -
Page 25: Assembling The Eslider
The points on the vehicle floor where the original vehicle seat was mounted serve as reference points during assembly. Figure 5.1: eSlider installation example 1 The installation kits shown are not included in the eSlider scope of delivery. -
Page 26: Assembling The Vec Control Unit - Eslider
Assembly Assembling the VEC control unit - eSlider Seat attachment Clamp 15 CAN BUS attachment Clamp 30 Ground CAN high CAN low CAN BUS / vehicle side Unscrew all 4 screws on the trim panel of the linear unit. Completely remove the trim panel. -
Page 27: Overview Of Plug Connections On The Vec Control Unit - Eslider
Assembly Overview of plug connections on the VEC control unit - eSlider M4/M5 M1/M2 X2/X4/X5/X15 X3/X18 X7/X9/X11/X17 X12/X14 X6/X8/X10/X16... -
Page 28: Assembling The Control Unit
Assembly Assembling the control unit Assemble the control unit on the lift unit. Use the relevant drill hole pattern depending on the position of the control unit. For this purpose, use the attachment set provided. The hexagon nuts must always be facing outwards. -
Page 29: Adjusting The Control Unit
Assembly Adjusting the control unit If all the control unit buttons are to be used, we recommend a horizontal positioning of the control unit. If only the control unit's memory function is to be used, we recommend positioning it at an angle of 25°. -
Page 30: Checking The Function
• Above all, check the function of the eSlider (see the "Operation" chapter): - Swivel positions - eSlider must turn in such a way that it does not knock into anything when it swivels inwards • The Twister must move along the slide rails without jamming. -
Page 31: Maintenance And Care
Maintenance and care Maintenance and care Safety information Only authorised and appropriately trained personnel may perform main- tenance and repair work on the eSlider. Arrange for functional faults to be remedied immediately by a specialist workshop. Maintenance/care Every 2 years... - Page 32 Maintenance and care Lubrication points Only use Autol TOP 2000 Longtine grease!
- Page 33 Maintenance and care Lubrication points Only use Autol TOP 2000 Longtine grease!
-
Page 34: Transport, Storage And Disposal
Disposal Comply with national waste disposal directives. We ensure that the majority of the materials used to make our eSlider are re- cyclable, right from the design phase. The packaging consists of cardboard boxes and, in some instances, films that can be handed in at recycling centres or disposed of in public waste collection bins in Germany. -
Page 35: Installation Record
Installation record Installation record This record will be completed if the driving aid is installed at an authorised work- shop. Customer: Installation date: Article designation: Time: Factory no.: Vehicle: Article: Article: supplied Licence plate no.: Vehicle acceptance: Note any damage & specific features below. Install- All screws are tight and have Do the indicator lights for the lat-... - Page 36 Veigel GmbH + Co. KG Verrenberger Weg 36 74613 Öhringen, Germany phone +49 (0) 7941 60585 0 fax +49 (0) 7941 60585 20 info@veigel-automotive.de www.veigel-automotive.de FOR EVERY VEHICLE A SOLUTION...
Need help?
Do you have a question about the eSlider and is the answer not in the manual?
Questions and answers