Advertisement
Advertisement
Table of Contents
Related Manuals for Peavey IPA 150 TII
Summary of Contents for Peavey IPA 150 TII
- Page 1 Cover for IPA 75/150T II...
- Page 2 Intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
- Page 3 LEVEL (1) Controls the volume level of the system. SUBSONIC FILTER (2) The "in" position of this switch activates the 18 dB/octave subsonic filter at 42 Hz. The "out" position removes the subsonic filter from the system. POWER ON LED (3) Indicates when AC power is being supplied to the unit.
- Page 4 The fuse is located within the cap of the fuseholder. If the fuse should fail, IT MUST BE REPLACED WITH THE SAME TYPE AND VALUE IN ORDER TO AVOID DAMAGE TO THE EQUIPMENT AND TO PREVENT VOIDING THE WARRANTY. If the amp repeatedly blows fuses, it should be taken to a qualified service center for repair.
-
Page 5: Installation Information
0.5% or less distortion with hum and noise at least 95 dB below rated output. The unit shall be called the Peavey Architectural Acoustics Division model IPA™ 75T II. IPA 150T II ARCHITECTURAL AND ENGINEERING SPECIFICATIONS The power amplifier input shall have screw terminal connections and a sensitivity switch. -
Page 6: Specifications
SPECIFICATIONS Output Power (IPA 75T II): 75 watts Output Power (IPA 150T II): 150 watts Frequency Response: Direct: 0.5 dB, 20 Hz to 20 kHz XFMR: 0.5 dB, 50 Hz to 20 kHz Distortion: 0.03% (1 kHz) S/N Ratio (20 kHz BW): 95 dB BLOCK DIAGRAM Power Bandwidth:... -
Page 7: Wiring Diagrams
Balanced Line Level Input Connections Figure 1 Balanced (1V/600 ) – Direct Output to Multiple Speakers in Parallel. Total Impedance = 4 Figure 3 WIRING DIAGRAMS Balanced (1V/600 ) Direct Output to 4 Speaker Figure 2 COM XFMR – COM XFMR –... - Page 8 Balanced (1V/600 ) COM XFMR To booster amplifier, etc. 1 V Balanced Output Connectors Figure 4 Balanced (1V/600 ) COM XFMR Jumper Installed 70V "Constant Voltage" Distribution System (Note: Jumper must be in place.) Figure 5...
- Page 9 For further information on other Peavey products, ask your Authorized Peavey Dealer for the appropriate Peavey catalog/publication: Bass Guitars Guitars Bass Amplification Guitar Amplification Sound Reinforcement Enclosures Microphones Keyboards Lighting Mixers, Powered/Non-Powered Accessories/Cables Effects Processors Axcess™ Wear The Peavey Beat™...
-
Page 10: Important Safety Instructions
16. The user should not attempt to service this equipment. All service work should be done by a qualified service technician. 17. This product should be used only with a cart or stand that is recommended by Peavey Electronics. 18. Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in susceptibility to noise induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time. - Page 11 If within one (1) year from date of purchase a properly installed product proves to be defective and Peavey is notified, Peavey will repair or replace it at no charge. (Note: Batteries and patch cords not covered.) “Original purchaser” means the customer for whom the product is originally installed.
- Page 12 ® ARCHITECTURAL ACOUSTICS® Features and specifications subject to change without notice. A Division of Peavey Electronics Corporation 711 A Street / Meridian, MS 39301 / U.S.A. / (601) 483-5376 / Fax 486-1278 ©1995 #80302229 Printed in U.S.A. 1/95...