Advertisement
Quick Links
Advertisement
Related Manuals for Laminata Shed 900
Summary of Contents for Laminata Shed 900
- Page 1 Ready. Set. Build. Shed 900 Installation Guide...
- Page 2 Ready. Set. Build.
- Page 3 Ask us. 0508 526 462 Laminata has created garden sheds focused on practical and functional design. Our MiniCLT panels make up the majority of the shed, ensuring strength and durability. The TPO rubber membrane roofing keeps the water out and the aluminum profiles cover the joins, making for a shed you’ll...
-
Page 4: Getting Started
Getting started. Materials list for Shed 900. Timber. Floor. Premade Base. 1733 x 825mm Rear Wall. CLT Panels. 135 x 30 x 1790mm (tongue ON) 275 x 30 x 1790mm 275 x 30 x 1790mm (NO Tongue) Side Walls. CLT Panels. 275 x 30 x 825mm 135-275 x 30 x 825mm (angle panels) Front Wall. - Page 5 Other. Roof. Equal Angle. 40 x 40 x 1800mm 40 x 40 x 1100mm Roof. TPO Rubber Roofing. 1160 x 1800mm Corners. Equal Angle. 40 x 40 x 1925mm 40 x 40 x 1800mm Door Jams/Frames. Equal Angle Channel. 31.75 x 31.75 x 1785mm Hardware.
- Page 6 Note. It pays to itemise all components prior to assembly. Step 01. Getting started. Prepare your work space. Ensure your premade base sits stable and level.
- Page 7 Note. For strength, the panels are staggered. Step 02. Attaching your first layer. First. Using 2x planks 275 x 28 x 825mm place them on top of the bearer overhang and screw fix 3x screws 8g x 65mm into the premade base. Panels should sit flush and square with the premade base.
- Page 8 Note. The top rear wall panel has no tongue. Step 03. Build up the walls. Continuing the staggered pattern, build up the rear and side walls using 5x CLT panels 275 x 28 x 1790mm, 1x CLT Panel (no tongue) 275 x 28 x 1790 and 12x CLT panels...
- Page 9 Note. This is a good time to ensure your shed is level and square. Step 04. Add the roof angle and lintel. First. Using the 2x CLT panels (angle panels) 135-275 x 28 x 825mm screw fix them as per step 2/3 to finish the side walls. Next.
- Page 10 Note. Skew screw the first CLT panel 275 x 28 x 298mm up into the lintel, ensuring this join is Step 05. tight and square. Installing front wing walls. First. Using the 12x CLT panels 275 x 28 x 298mm, screw fix from the top down with 2x screws 8g x 65mm in each...
- Page 11 Note. Fix the front and rear roof panel down to the front and rear wall. Step 06. Putting the roof on. Using 3x CLT panels 275 x 28 x 1790mm, start from the back, overhanging the first plank 100mm past the rear wall.
- Page 12 Note. Choose dark colours to avoid damage to the timber substrate. Step 07. Coating (optional). To protect your new shed, we suggest staining with a suitable outdoor timber stain prior to installing aluminum profiles and roofing. We suggest using a Cabot’s water or oil based stain with a Cabot’s broom applicator.
- Page 13 Note. You can also glue down the membrane. Step 08. Install TPO rubber roofing. Roll out the TPO rubber membrane over the roof panels and tac with either a staple gun or small screws around edges.
- Page 14 Note. Pre-drill hobs with a 3mm pre-drill bit to make attaching aluminium easier. Step 09. Aluminium profiles. Using the Self Drilling 8g x 30mm, fix the aluminum channels to the applicable joins and corners; 2x Roof Equal Angle 40 x 40 x 1800mm 2x Roof Equal Angle 40 x 40 x 1100m 2x Door Jams...
- Page 15 Note. If doors don’t sit straight, double check your shed is sitting level and Step 10. adjust accordingly. Doors and hardware. Attach the door hinges to the premade doors, ensuring they are positioned correctly for the doors to open outward. Evenly space the hinges to sit 100mm from both the top and bottom of the door.
- Page 16 Ready. Set. Build. Find out more. www.laminata.nz Ask us. 0508 526 462...