Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for MAASLAND ML420
- Page 1 HANDLEIDING ML420...
-
Page 2: Table Of Contents
ELEKTRISCHE SLOTEN 26 0123 MODELLEN ML420, MB420, MG420 1. INHOUDSOPGAVE Inhoudsopgave.................................2 Algemene informatie..............................2 Inhoud en doel..............................3 2.2 Doelgroep................................3 3. Veiligheid en naleving..............................3 Veiligheidsinformatie..............................3 3.2 Informatie over naleving van de regelgeving.......................3 Productinformatie..............................5 Productbeschrijving..............................5 4.2 Inhoud van de verpakking............................5 4.3 Technische informatie............................5 Afmetingen..............................6... -
Page 3: Inhoud En Doel
2. ALGEMENE INFORMATIE 2.1 INHOUD EN DOEL Dit document beschrijft installatie, aansluiting, bediening en onderhoud van het ML420 slot. Lees het document zorgvuldig en neem de aanwijzingen in acht. Ze bevatten belangrijke informatie voor een betrouwbare installatie en een probleemloze werking. - Page 4 ELEKTRISCHE SLOTEN 26 0123 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
-
Page 5: Productinformatie
The ability to release when requested even if there is excessive load on the door. The bolt pin of the ML420 operates on a cam action which enables the bolt pin to pull a door into place. In practice as the door closes it may come to rest in a position that is not fully closed, especially if it closing against a door seal of some type. -
Page 6: Afmetingen
ELEKTRISCHE SLOTEN 26 0123 5. AFMETINGEN 5.1 AFMETINGEN SLOT Dimensions shown are approximate and subject to change without prior notice. 96mm 47mm 160mm 30mm 140mm 10mm 10mm 5.2 AFMETINGEN SLUITPLAAT Dimensions shown are approximate and subject to change without prior notice. 160mm 107mm 14mm... -
Page 7: Afmetingen Behuizing
ELEKTRISCHE SLOTEN 26 01 2 3 5.3 AFMETINGEN BEHUIZING Dimensions shown are approximate and subject to change without prior notice. 34mm 125mm 20mm 56mm 164mm 5.4 AFMETINGEN AFDEKPLAAT Dimensions shown are approximate and subject to change without prior notice. 58mm 165mm 5.5 AFMETINGEN MONTAGEPLAATJES Dimensions shown are approximate and subject to change without prior notice. -
Page 8: Voorbereiding Installatie
ML420 will pull the door into alignment with ease. This misalignment could be caused by an installed weather seal or natural distortions in the door assembly. The ML420 can be installed vertically or horizontally but is not designed to be mounted in a floor cavity firing upwards or in a wet environment. -
Page 9: Voorbereiding Bekabeling
The ML420 can be set to one of two operating modes before installation, Fail Safe or Fail Secure. When the operating mode is set to Fail Safe, supply voltage is applied to the control input to lock the door, and the ML420 will unlock in the event of power loss. -
Page 10: Montage
ELEKTRISCHE SLOTEN 26 0123 7. MONTAGE 7.1 INBOUW MONTAGE (HOUT) 1. Cutting the mortice Referring to the product dimension drawings, a mortice is cut into the door frame to fit the lock and a mortice is cut into the door leaf to fit the strike. Wooden doors and frames require full mortices with space made behind the lock body to accommodate the wire connections. -
Page 11: Inbouw Montage (Profiel)
ELEKTRISCHE SLOTEN 26 01 2 3 7.2 INBOUW MONTAGE (PROFIEL) 1. Cutting the mortice Referring to the product dimension drawings, a mortice is cut into the door frame to fit the lock and a mortice is cut into the door leaf to fit the strike. Metal doors and frames, being hollow, often only require a single rectangle cut-out to accommodate the lock face plate or strike plate. -
Page 12: Opbouwmontage (Hout)
ELEKTRISCHE SLOTEN 26 0123 7.3 OPBOUWMONTAGE (HOUT) 1. Preparing the mounting surface Install two 10Gx1” self-tapping screws (included with housing) in the mounting surface, as per the product dimension drawings they should be 125mm apart, 20mm from the surface edge. 2. -
Page 13: Opbouwmontage (Glas)
ELEKTRISCHE SLOTEN 26 01 2 3 7.4 OPBOUW MONTAGE (GLAS) 1. Fitting the housing Clean the glass surface with isopropyl alcohol and peel the protective layer from the double sided tape of the housing. Position the housing flush with the edge of the glass, and press down to adhere tape to surface. -
Page 14: Bekabeling
8.1 INFORMATIE BEKABELING The ML420 is supplied with a 7-way wire loom that plugs directly into the lock. The wiresare colour coded as per table below, with the power and control wires being essential connections and the four monitor connections being optional. -
Page 15: Stroomprincipe
With the door now open the Bolt Position and Door Position monitors change to open contact state. The ML420 will remain unlocked as long as the door is open but will instantly re-lock when... -
Page 16: Onderhoud
ELEKTRISCHE SLOTEN 26 0123 10. ONDERHOUD 10.1 ONDERHOUD EN REINIGING The lock has been factory lubricated for life and is maintenance free. The use of other lubricants is not permitted and will void the warranty. This lock contains electromechanical and electronic components that are subject to wear and tear depending on use and on-site installation conditions. - Page 17 ELEKTRISCHE SLOTEN 26 01 2 3 info@maaslandgroep.nl www.maaslandgroep.nl...