Table of Contents
Advertisement
Quick Links
PDWR Wireless Signal Repeater
Instruction Manual
Available in Aluminum
or Stainless Steel
•
Wireless Repeater Unit Improves Signal Strength and Range for PDW Wireless Systems
•
Use in PDW30 Point to Point and PDW90 Point to Multi-Point Wireless Systems
•
Increase Range an Additional 1 Mile Line-of-Sight, 500 Feet Indoor
•
Increases Range of the Analog, Digital I/O and Modbus Signals
•
Simple to Configure Using PDW Manager Programming Software and On-Board USB
•
Use CapTouch Through-Glass Buttons to Change Network ID
•
Device Communication Secured by Enabling 128-bit AES Encryption
•
Password Protection
•
IP68, NEMA 4X Aluminum & Stainless Steel Enclosures With Plenty of Room for Field Wiring
•
Operating Temperature Range: -55 to 75°C (-67 to 167°F)
•
Conformal Coated PCBs for Dust & Humidity Protection
•
Flange for Wall or Pipe Mounting; Loop for Stainless Steel Tag; Holes for Tamper-Proof Seal
•
9-30 VDC Power
•
3-Year Warranty
PRECISION DIGITAL CORPORATION
233 South Street • Hopkinton MA 01748 USA
Tel (800) 343-1001
www.predig.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Precision Digital Corporation PDWR
Summary of Contents for Precision Digital Corporation PDWR
- Page 1 PDWR Wireless Signal Repeater Instruction Manual Available in Aluminum or Stainless Steel • Wireless Repeater Unit Improves Signal Strength and Range for PDW Wireless Systems • Use in PDW30 Point to Point and PDW90 Point to Multi-Point Wireless Systems •...
-
Page 2: Table Of Contents
Figure 2. Enclosure Dimensions – Side View ..........10 Figure 3. Enclosure Dimensions – Top View ..........10 Figure 4. PDWA6963-SS Stainless Steel Pipe Mounting Kit ......10 Figure 5. PDWR Repeater Display Module Connectors ........ 11 Figure 6. Power Connections ................11... -
Page 3: Introduction
• Read complete instructions prior to installation strength. and operation of the device. PDWR repeaters can be used to broadcast over very long distances or around permanent obstacles. The PDWR repeaters are available in either aluminum • Risk of electric shock or personal injury. -
Page 4: Key Features
PDW Manager PC Software allows for programming The display module designed specifically for the the PDWR repeater units from a PC with a USB PDWR wireless units are easy to remove making it connection. The units connect to a PC via the USB convenient for wiring the unit. -
Page 5: Captouch Through-Glass Buttons
Buttons Aluminum or Stainless Steel The PDWR repeater units are equipped with four The PDWR repeater units are available in an IP68, capacitive sensors that operate as through-glass NEMA 4X aluminum or stainless steel enclosure. The buttons so that they can be operated without... -
Page 6: Application Example
Extending Signal Range with PDWR Repeaters The PDWR repeaters are used to retransmit wireless signals when connectivity between the PDW30 primary and secondary units or the PDW90 base station and field units are out of range or are obstructed by other objects or structures. -
Page 7: Ordering Information
PDA-SSTAG (See website for convenient ordering form) Notes: 1. The PDWR repeater units come standard with two 3/4" NPT conduit holes. To order models with M20 conduit holes instead, add -22 at the end of the part number (e.g. PDWR-GP-AL-REP-22) 2. -
Page 8: Specifications
PDWR Wireless Signal Repeater Instruction Manual Specifications Enclosure Material -AL Models: Except where noted all specifications apply to operation at +25°C. ASTM A413 LM6 die-cast aluminum, General copper-free, enamel coated. -SS Models: Display 32-character dual-line alphanumeric dot ASTM A743 CF8M investment-cast... -
Page 9: Safety Information
There are three ways to mount the PDWR repeater: the following measures: Re-orient or relocate the receiving antenna, Increase the separation 1. -
Page 10: Dimensions
PDWR Wireless Signal Repeater Instruction Manual Dimensions Figure 3. Enclosure Dimensions – Top View PDWA6963-SS Stainless Steel Pipe Mounting Kit Figure 1. Enclosure & Antenna Dimensions – Front View Figure 4. PDWA6963-SS Stainless Steel Pipe Mounting Kit Figure 2. Enclosure Dimensions – Side View... -
Page 11: Connections
Connector Labeling / Location The only connections made to the PDWR repeater is power which is made to a two-position screw terminal connector as shown in the following diagram. The connector is located on the rear of display module. -
Page 12: Setup And Programming
Use the MENU button to enter or exit programming mode, the NEXT There are only three items to program on the PDWR button to cycle forward through menu options, the UP repeater: network ID, password, and encryption. -
Page 13: Captouch Buttons
Instructions on the use of PDW Manager to program completes a self-calibrating routine (which can take the PDWR repeater wireless units can be found under up to 20 seconds). Additionally, the sensors are disa- Programming with PDW Manager on page 15. -
Page 14: Setup Menu
PDWR Wireless Signal Repeater Instruction Manual Password Setup Setup Menu The setup menu consists of network ID, password, The wireless repeater may be protected with a four- and factory defaults restoration. digit numeric password in order to prevent unauthor- ized tampering. When a password has been set, you will be prompted to enter that password in order to ac- cess the device menu. -
Page 15: Programming With Pdw Manager
Programming with PDW Manager PDW Manager allows programming of the PDWR wireless repeater unit from a PC with a USB connection. The unit connects to a PC via the micro-USB connection on the side of the electronics module, underneath the enclosure cover. -
Page 16: Networking Settings And Security
PDWR Wireless Signal Repeater Instruction Manual Networking Settings and Security Device communication can be secured by enabling 128-bit AES encryption. A channel mask may also be set for interference immunity. The encryption key and channel mask may be entered on the Advanced tab. -
Page 17: Troubleshooting
• If communicating over distance of miles, consider installing additional PDWR repeaters or a high gain directional antenna. • If there are multiple PDW30 wireless bridges, verify Multiple wireless devices in the area that each pair has its own unique Modbus ID. - Page 18 PDWR Wireless Signal Repeater Instruction Manual Symptom Possible Cause Corrective Action • Check RSSI. If signal is too low, consider moving Signal is too low. devices closer together, clearing obstacles in wireless path, or mounting devices higher. • Ensure devices are on parallel plane.
- Page 19 PDWR Wireless Signal Repeater Instruction Manual Symptom Possible Cause Corrective Action • The device must be powered by a 9-30 VDC power Wireless device is not powered. supply in order for the PC to recognize it. Power the Device will not connect wireless device and try again.
- Page 20 PDWR Wireless Signal Repeater Instruction Manual Symptom Possible Cause Corrective Action Other symptoms not described above. If you are experiencing a symptom not listed here, or the suggested troubleshooting steps do not alleviate your problem, please attempt to restore the wireless devices to system defaults by following the instructions on page 14.
- Page 21 PDWR Wireless Signal Repeater Instruction Manual This page is intentionally left blank.
- Page 22 PDWR Wireless Signal Repeater Instruction Manual Contact Precision Digital Technical Support Call: (800) 610-5239 or (508) 655-7300 Email: support@predig.com Sales Support Call: (800) 343-1001 or (508) 655-7300 Email: sales@predig.com Place Orders Email: orders@predig.com For the latest version of this manual please visit www.predig.com...
Need help?
Do you have a question about the PDWR and is the answer not in the manual?
Questions and answers