G-Force WR 040 Instruction Manual

- it is obligatory to verify the free space required beneath the user at the workplace before each occasion of use the fall
arrest system, so that, in the case of a fall, there will be no collision with the ground or other obstacle in the fall path. The
required value of the free space should be taken from instruction manual of used equipment.
- there are many hazards that may affect the performance of the equipment and corresponding safety precautions that have
to be observed during equipment utilization, especially:- trailing or looping of lanyards or lifelines over sharp edges,- any
defects like cutting, abrasion, corrosion, - climatic exposure,- pendulum falls,- extremes of temperature,- chemical reagents,-
electrical conductivity.
- personal protective equipment must be transported in the package (e.g.: bag made of moisture-proof textile or foil bag or
cases made of steel or plastic) to protect it against damage or moisture.
- the equipment can be cleaned without causing adverse effect on the materials in the manufacture of the equipment. For
textile products use mild detergents for delicate fabrics, wash by hand or in a machine and rinse in water. Plastic parts can
be cleaned only with water. When the equipment becomes wet, either from being in use or when due cleaning, it shall be
allowed to dry naturally, and shall be kept away from direct heat. In metallic products some mechanic parts (spring, pin,
hinge, etc.) can be regularly slightly lubricated to ensure better operation.
- other maintenance and cleaning procedures should be adhered to detailed instructions stated in the manual of the
equipment.
- personal protective equipment should be stored loosely packed, in a well-ventilated place, protected from direct light,
ultraviolet degradation, damp environment, sharp edges, extreme temperatures and corrosive or aggressive substances.
IT IS THE RESPONSIBILITY OF THE USER ORGANISATION TO PROVIDE THE IDENTITY CARD AND TO FILL IN THE DETAILS REQUIRED.
THE IDENTITY CARD SHOULD BE FILLED IN ONLY BY A COMPETENT PERSON RESPONSIBLE FOR PROTECTIVE EQUIPMENT. THE
IDENTITY CARD SHOULD BE FILLED IN BEFORE THE FIRST USE OF THE EQUIPMENT. ANY INFORMATION ABOUT THE EQUIPMENT LIKE:
Periodic Inspections, REPAIRS, REASONS OF EQUIPMENT'S WITHDRAWN FROM USE SHALL BE NOTED. THE IDENTITY CARD
SHOULD BE STORAGED DURING A WHOLE PERIOD OF EQUIPMENT UTILIZATION. DO NOT USE THE EQUIPMENT WITHOUT THE

IDENTITY CARD.

IDENTITY CARD
MODEL AND TYPE OF EQUIPMENT
REF. NUMBER
SERIAL NUMBER
USER NAME
DATE OF PURCHASE
PERIODIC EXAMINATION AND REPAIR HISTORY
REASON FOR CONDITION OF DEVICE
DATE
SERVICING/REPAIR
1
2
3
4
5
SafetyLiftinGear.com
Unit R1D Rockingham Gate Poplar Way
West Cabot Park Bristol BS11 0YW
Tel: 0808 123 69 69 Fax: 0117 9381 602
sales@safetyliftingear.com
DATE OF MANUF.
DATE OF FIRST USE
NAME AND SIGNATURE
AFTER SERVICING OF COMPETENT PERSON
Notified body, at which the European certification was Iissued
and which supervises the production of the equipment:
APAVE SUDEUROPE SAS - 8 rue Jean-Jacques Vernazza -
CS-60193 – 13322 MARSEILLE Cedex 16, France - No. 0082
PRODUCENT: PROTEKT, 93-403 LODZ, ul. Starorudzka 9, POLAND,
TEL: (48 42) 680 20 83, FAX: (48 42) 680 20 93, www.protekt.com.pl
Instruction Manual
Read carefully
the manual
before use
the equipment

ESSENTIAL FEATURES

The retractable-type fall arrester device WR 040 is a component
of the personal protective equipment against falls from a height
and conforms to EN 360:2002.
The fall arrester WR 040 is the protection for one person only.
Available lengths of the device:
- Ref. WR 040 18 - 1,8 meters
Maximum Working Load:140 kg.

MARKING OF THE FALL ARRESTER

NEXT
EXAMINATION
DATE
2012
Inspect
the device
before each
use
RETRACTABLE TYPE FALL ARRESTER
Ref. WR 040
Type of the equipment
Reference number
of the device
WR040 018 WR040 018
Month and year of
manufacture
Serial number of the device
Number and year
of the European Standard
CE mark and number of notified body
inspecting the equipment production
according to the article 11
of Directive 89/686/EEC
device manufacturer or distributor
month and year of the manufacturer's
next inspection
Don't use the device after this date
Attention: Before the first use
mark the date of the first inspection
(date of first use +60 months,
e.g. first use 01.2013 - mark inspection 01.2018)
check locking
before use
before each
read the manual
use
Top swivel
for attaching
the device
Webbing retractor
with brake
inside plastic cover
Working webbing
17mm width made
from Technora and
polyester
Energy absorber
Snap hook
(Range of alternative
snap hooks with
fall indicator and
swivel function
as an option)
tested with "fall
factor 2"
OK
range
according to
of operating
recomendation
temperatures
CNB/11.085
RFU 11.085
use only a full body
maximum
harness conformed
working
to EN 361
load
140 kg
store the device in
don't realese rapidly
a protected place
unwinded webbing
don't repair
maximal admissible
the device
deflection of the cable
yourself
from the vertical line
Attach the device
don't use the device
to the anchorage
with damaged
point using the top
webbing
loop of the energy absorber