Advertisement
Quick Links
+44 (0)1635 294600 | info@i-lcd.com | www.i-lcd.com
Intelligent Display Solutions, Unit 2, Berkshire Business Centre,
Berkshire Drive, Thatcham, Berkshire, RG19 4EW
A division of Intelligent Group Solutions Ltd
Quick Start Guide
AM-800480N6TZQW-T06H
CONTENTS
page 2
page 2
page 3
© IGS Version V1
page 4
page 6
1 of 9
Advertisement
Related Manuals for IDS AM-800480N6TZQW-T06H
Summary of Contents for IDS AM-800480N6TZQW-T06H
-
Page 1: Table Of Contents
© IGS Version V1 Quick Start Guide AM-800480N6TZQW-T06H CONTENTS Kit Content page 2 Connect the driver card to the power supply and HDMI source page 4 Required Parts not Supplied in Kit page 2 Part 2: Connecting the touch panel... -
Page 2: Kit Content
© IGS Version V1 KIT CONTENTS Item Description Display with touch panel Driver card USB adapter card Display with touch panel Driver card USB adapter card REQUIRED PARTS NOT SUPPLIED IN THE KIT Item Description RS Part Number 12V 2A Power supply with 2.1mm x 5.5mm DC Jack 144-0971 Generic USB mini lead 193-2871... -
Page 3: Part 1: Connecting The Driver Card To The Display
© IGS Version V1 PART 1: CONNECTING THE DRIVER CARD TO THE DISPLAY Connect the LVDS connector from the driver card to the back of the LCD. Take care to line up the pins and use the correct orientation as per the picture below. It should look like this when the connector is correctly installed. -
Page 4: Connect The Driver Card To The Power Supply And Hdmi Source
© IGS Version V1 CONNECTING THE DRIVER CARD TO THE POWER SUPPLY AND HDMI SOURCE Connect the power connector to the 12V DC power supply using a 2.1mm connector with centre positive and barrel negative. Connect the HDMI connector to your source. Turn the power switch to the ON position. - Page 5 © IGS Version V1 CONNECTING THE DRIVER CARD TO THE POWER SUPPLY AND HDMI SOURCE +44 (0)1635 294600 | info@i-lcd.com | www.i-lcd.com Intelligent Display Solutions, Unit 2, Berkshire Business Centre, Berkshire Drive, Thatcham, Berkshire, RG19 4EW 5 of 9 A division of Intelligent Group Solutions Ltd...
-
Page 6: Part 2: Connecting The Touch Panel
© IGS Version V1 PART 2: CONNECTING THE TOUCH PANEL The display has an FFC tail with the USB connections. Remove any packing foam and tape to release the touch control board from the back of the display. Place the display face up and line up the small USB connector PCB. +44 (0)1635 294600 | info@i-lcd.com | www.i-lcd.com Intelligent Display Solutions, Unit 2, Berkshire Business Centre, Berkshire Drive, Thatcham, Berkshire, RG19 4EW... - Page 7 © IGS Version V1 PART 2: CONNECTING THE TOUCH PANEL Locate CN4 on the PCB and carefully lift up the flap. Note the orientation of the FFC and the PCB, it must be connected the correct way round or damage may occur. Push the FFC tail into the connector far enough so that the dark strengthening section is all the way in, and close the flap.
- Page 8 © IGS Version V1 PART 2: CONNECTING THE TOUCH PANEL The touch panel can now be connected to a PC and will be automatically installed by MS Windows10. The FFC tail and controller are very fragile and easily torn. It is recommended that once connected to the breakout board everything is secured to the back of the display using tape.
- Page 9 The values contained in this data sheet can change due to technical innovation. Any such changes will be made without separate notification. If you require further assistance or have a specific or custom enquiry, please contact the IDS team via email or phone. Alternatively please visit our website for more product info and to see our full range.