Subscribe to Our Youtube Channel
Related Manuals for Powermat PM0711
Summary of Contents for Powermat PM0711
- Page 1 PM0711; PM0715 USER MANUAL PLACE IMAGE HERE PNEUMATIC IMPACT WRENCH PM-KPU-1550T / PM-KPU-1550TB ORIGINAL MANUAL...
-
Page 2: Table Of Contents
TABLE OF CONTENTS TABLE OF CONTENTS .............................. 2 WARNING / INFORMATION SYMBOLS ..................3 APPLICATION OF THE DEVICE ......................... 3 TECHNICAL DATA ..........................4 SAFETY ........................... 4 General safety instructions ....................4 Work area safety .......... -
Page 3: Warning / Information Symbols
WARNING / INFORMATION SYMBOLS ATTENTION: Before using the device, carefully read the instruction manual and safety recommendations. Keep the instructions. ATTENTION: Hearing protection is recommended. ATTENTION: Use protective gloves. SIGN OF CROSSED BASKET: An order to collectively collect used equipment and to throw it away with other waste. DISPOSAL OF WORN See the section "... -
Page 4: Technical Data
TECHNICAL DATA Model PM-KPU-1550T PM-KPU-1550TB 1/4 ”(Recommended cable min. 1/4 ”(Recommended cable min. Air connection diameter 3/8 ") 3/8 ") 7,500 rpm 7,500 rpm Turnover Maximum moment 1550 Nm 1550 Nm rotary Driver size 1/2 " 1/2 " Impact mechanism Twin hammer (double hammer) Twin hammer (double hammer) Maximum working pressure... -
Page 5: Safety Related To Use And Maintenance
d) Remove any adjustment wrenches from the tool before turning it on. A tool or wrench left in a rotating part of the tool may cause injury. e) Stay low. Maintain proper posture and balance at all times. This enables better control of the tool in unexpected situations. -
Page 6: Safety Rules Related To The Use Of Pneumatic Tools
6. A damaged switch should be replaced at an authorized service center. Do not use a tool with an inoperative on / off switch. 7. Do not leave the tool unattended when it is turned on. Always switch off the tool and wait for it to come to a complete stop before leaving the work site. -
Page 7: After Work
Warning! It is unacceptable: ✓ overpressure to increase the power of the tool ✓ direct the pressure hose towards yourself or others. ✓ touching parts of moving devices ✓ allowing any persons to work in their position without the knowledge of their supervisor ✓... -
Page 8: Preparation To Work
9. Do not grasp the tool too hard. The handle should be as light as possible and at the same time allow good control of the tool. 10. To reduce the vibration level, maintain the tool according to the instructions. Stop work immediately if excessive vibration occurs. -
Page 9: Device Description
DEVICE DESCRIPTION MODEL: PM-KPU-1550T / PM-KPU-1550TB Rotation switch Trunnion (1/2 ") Switch Air connection Screw on the connector... -
Page 10: Initial Activities
Repair of power tools should be performed only by qualified personnel using original spare parts. This ensures the safe use of the device. Address: Powermat service ul. Obrońców Poczty Gdańskiej 97 42-400 Zawiercie Tel. 32 670 39 68, internal 4 e-mail: serwis@powermat.pl... -
Page 11: Service
ERWIS Tools should only be repaired by qualified personnel using original spare parts. This ensures the safe use of the device. Address: Powermat service ul. Obrońców Poczty Gdańskiej 97 42-400 Zawiercie Tel. 32 670 39 68, internal 4 e-mail: serwis@powermat.pl STORAGE The tool and its accessories should be stored in a dry and clean place, away from flammable liquids. -
Page 12: Manufacturer's Data
You can also take the old equipment back to the collection point. More information on the collection points for used devices is available at the website: https://sklep.powermat.pl/webpage/pl/recycling.html MANUFACTURER'S DATA PH Powermat TMK Bijak Sp. Jawna Ul. Obrońców Poczty Gdańskiej 97 42-400 Zawiercie https://www.powermat.pl...
Need help?
Do you have a question about the PM0711 and is the answer not in the manual?
Questions and answers