Subscribe to Our Youtube Channel
Related Manuals for Powermat PM-KPU-1550M
Summary of Contents for Powermat PM-KPU-1550M
- Page 1 PM0805; PM0806 USER MANUAL PLACE IMAGE HERE PNEUMATIC IMPACT WRENCH PM-KPU-1550M / PM-KPU-1550MB ORIGINAL MANUAL...
-
Page 2: Table Of Contents
TABLE OF CONTENTS TABLE OF CONTENTS ..................................2 WARNING / INFORMATION SYMBOLS ........................3 APPLICATION OF THE DEVICE ............................3 TECHNICAL DATA................................5 SECURITY................................5 General safety instructions ................................5 Hazards related to parts thrown out .......... -
Page 3: Warning / Information Symbols
WARNING / INFORMATION SYMBOLS ATTENTION: Before using the device, carefully read the instruction manual and safety recommendations. Keep the instructions. ATTENTION: Use protective headphones. ATTENTION: Use safety glasses. ATTENTION: The use of a dust mask is recommended ATTENTION: Use protective gloves. ATTENTION: The use of protective clothing is recommended. - Page 4 As part of the continuous improvement of its products, the manufacturer reserves the right to make slight differences in this manual, which should be noted. The device may only be repaired and maintained by an authorized service center. For safety reasons, the device must not be used by children and adolescents under 18 years of age and by persons under the influence of alcohol, drugs or other intoxicants.
-
Page 5: Technical Data
TECHNICAL DATA Model PM-KPU-1550M PM-KPU-1550B 1/4 ”(Recommended cable min. 1/4 ”(Recommended cable min. Air connection diameter 3/8 ") 3/8 ") 8,000 rpm 8,000 rpm Turnover Maximum moment 1550 Nm 1550 Nm rotary Driver size 1/2 " 1/2 " Impact mechanism... -
Page 6: Hazards Related To Parts Thrown Out
• Please treat your device carefully. Keep the machine in such a condition that the quick couplings are firmly attached to the hose and wrench. WITH HAZARDS RELATED TO EJECTED PARTS Damage to the workpiece, accessories, or even the insertion tool can cause the part to be ejected at high speed. Always wear impact resistant eye protection. -
Page 7: Hazards Caused By Accessories
WITH HAZARDS CAUSED BY ACCESSORIES Disconnect the tool from the power source before changing the inserted tool or accessory. Do not touch attachments and accessories while the tool is running, as this increases the risk of cuts, burns, or injury due to vibration. Use accessories and consumables only in sizes and types recommended by the manufacturer. -
Page 8: Preparation To Work
vibration. Do not use worn or poorly fitted attachments as this can significantly increase the vibration level. Select, maintain and replace worn tools in accordance with the recommendations in the instruction manual. This will avoid an unnecessary increase in the vibration level. Shielding mounting should be used where possible. If possible, support the weight of the tool in a stand, tensioner or balancer. - Page 9 If the wrench suddenly stops turning during operation, do not increase the operating pressure above 6.2 bar (90 psi). Such pressure could damage the bolt and wrench, or seriously injure yourself. Use a different tool. After loosening / tightening the screw, release the trigger and remove the cap with the wrench. The wrench stops a few seconds after you release the trigger.
-
Page 10: Device Description
DEVICE DESCRIPTION MODEL: PM-KPU-1550M / PM-KPU-1550MB Air connection Trunnion (1/2 ") Air outlet channels On / off switch Torque switch and control pos... -
Page 11: Preliminary Steps
PRELIMINARY STEPS a) Open the package, then take out the device. b) Remove the protective foil and transport protection (if any). c) Check if the package includes dismantled parts and keys. d) Check that the machine and accessories have not been damaged during transport. e) Keep the packaging. -
Page 12: Connecting The Tool To The Pneumatic System
DISCONNECTING THE TOOL FOR THE PNEUMATIC SYSTEM The figure shows the recommended connection of the tool to the pneumatic system. The method shown will ensure the most effective use of the tool, as well as extend the life of the tool. Apply a few drops of SAE 10 oil to the air inlet. Screw the appropriate end for the air supply hose to the air inlet thread. -
Page 13: Other Maintenance Activities
SAE 10 oil designed for air tool maintenance is recommended. Connect the tool and let it run for a short time. Warning! WD-40 cannot be used as a proper lubricant. Wipe off any excess oil that leaked from the oil drain holes. Any leftover oil can damage the tool seals. -
Page 14: Warranty
Repair of power tools should be performed only by qualified personnel using original spare parts. This ensures the safe use of the device. Address: Powermat service ul. Obrońców Poczty Gdańskiej 97 42-400 Zawiercie Tel. 32 670 39 68, internal 4... - Page 15 Comments to order. In this way, you can return used electrical and electronic equipment to the place of delivery. You can also take the old equipment back to the collection point. More information on the collection points for used devices is available at the website: https://sklep.powermat.pl/webpage/pl/recycling.html...
-
Page 16: Part Diagram
PART DIAGRAM IDLOCK EXPLODED CIRCUIT MANUFACTURER'S DATA PH Powermat TMK Bijak Sp. Jawna Ul. Obrońców Poczty Gdańskiej 97 42-400 Zawiercie https://www.powermat.pl DECLARATION OF CONFORMITY...
Need help?
Do you have a question about the PM-KPU-1550M and is the answer not in the manual?
Questions and answers