Subscribe to Our Youtube Channel
Related Manuals for Daewoo DAT5055R
Summary of Contents for Daewoo DAT5055R
- Page 1 DAT5055R Gasoline Tiller USER'S MANUAL www.daewoopowerproducts.com Manufactured under license of Daewoo International Corporation, Korea...
-
Page 2: Table Of Contents
INDEX 1. MAIN SPECIFICATION ..........................2 2. PRODUCT PICTURE ..........................2 3. PACKAGING LIST ........................... 3 4. INSTALLATION INSTRUCTION ......................5 5. CHECKING BEFORE OPERATION ......................7 6. OPERATION INSTRUCTION ........................8 7. MAINTENANCE ............................ 10 8. CHANGE ENGINE OIL .......................... 11 WARRANTY ............................... -
Page 3: Main Specification
FOREWORD PLEASE READ THIS MANUAL BEFORE OPERATION The manual contains these parts: assembly, operation, maintenance and service. 1. MAIN SPECIFICATION 4-stroke, air cooled Engine single cylinder, OHV 3.0/3600 Max Power (hp/rpm) Displacement (cc) Fuel tank capacity (L) Oil tank capacity (L) Tiling width (mm) Tiling diameter (mm) Tine speed (rpm) -
Page 4: Packaging List
3. PACKING LIST Please check them before installing （refer to Figure 2） . 1.Tiller………………………………………………………………………………………......… 1 PCS. 2.Girder……………………………………………………………………………………....... 1 PCS. 3.Wheel assy……………………………………………………………………………......…… 1 PCS. 4.Right blade cover…..……………………………………………………………………......1 PCS. 5.Blade disc…………………………………………………………………………………......2 PCS. 6.Resistance rod……………………………………………………………………………......1 PCS. 7.Safety plate….……………………………………………………………………………......1 PCS. 8.Right blade assy….…………………………………………………………………….......….. -
Page 6: Installation Instruction
Caution Please read this manual before operation It is dangerous to touch the rotating blades. Other people should keep safety distance away from the machine when it is working. Prohibit standing in the front of the machine to avoid accident when it is working. The spark plug must be pulled out when it is in the process of maintenance or repair Do not touch the muffler to avoid scalding or injury, when it is working or it is still hot. - Page 7 RIGHT BLADE COVER 3. Refer to figure 5 to install the Blade cover. BOLT M8*16 FIGURE 5 BLADE DISC 4. Refer to Figure 6 to install the Blade disc 1.PIN(LONG) 2.COTTER PIN FIGURE 6 BOLT：M8×50 5. Refer to figure 7 to install the Wheel. WHEEL SPRING FIGURE 7...
-
Page 8: Checking Before Operation
7. Refer to figure 9 to install the Handle 1. HANDLE LOCK LEVER BOLT：M8×70 2.COTTER PIN HANDLE FIGURE 9 8. Refer to figure 10 to install the Safety plate. BOLT：M6×35 SAFETY PLATE FIGURE 10 5. CHECKING BEFORE OPERATION In order to keep a safe tiller, do daily checking. Engine Oil Checking 1) Keep the engine in a horizontal position. -
Page 9: Operation Instruction
Warning ： If the level is too low, it may cause serious damage to the engine when the engine is working Please use clean and good quality 4-stroke engine oil. Run with other engine oil or dirty oil may shorten the lifetime of the engine severely. Air Filter Checking Warning: never run the engine without an air cleaner, or severe wear of the engine may be resulted in. - Page 10 OPEN CLOSE CHOKE LEVER FUEL SWITCH OPEN CLOSE FIGURE 13 FIGURE 14 3) Push below switches to the “ON” position. （ Refer to figure 15) FIGURE 15 4) Pull the starting handle slowly until you feel the resistance, and then pull out it suddenly and quickly.
-
Page 11: Maintenance
How to stop the engine turn the engine switch to OFF position . (Figure 15) ADJUST NUT FIGURE 18 How to adjust the clutch If the main clutch cable is not adjusted well (too tight or loose), the clutch may not work well. 1) Starting the engine. -
Page 12: Change Engine Oil
Frequency Each First Each Every 6 Each time month season month or year Items 100 hrs 20hrs 50hrs 300hr ○ Engine Oil Oil level check ○ ○ Replace ○ Reduction Gear Oil Oil level check ○ ○ Replace ○ Air Cleaner Check ○... - Page 13 Clean the air filter If the air cleaner is jam, it will output less enough air and cause fuel consumption increase. Check and clean it periodically. Cleaning Period: Once 50 hours’ working. If work in hervy dust area, check it every day or once 10 hours. Replace: each year or 300 hours’...
- Page 14 spark plug . 9) Measure the spark plug clearance with a thickness feeler. The clearance should be 0.6~0.7mm. If adjustment is necessary, bend the side electrode carefully. 10) Check if the spark plug gasket is in good condition. 11) Screw the spark plug to the bottom first by hand and then screw up with a spark plug wrench and compress the gasket.
-
Page 15: Warranty
Manufactured under license of Daewoo International Corporation, Korea...
Need help?
Do you have a question about the DAT5055R and is the answer not in the manual?
Questions and answers