Parts & Description LIST OF COMPONENTS Push Rod Processing Bowl Cover Chopping Blade Unit Drive Shaft Cover Processing Bowl Drive Shaft Motor unit ON/OFF & Speed Rotary Knob Grating Blade 10. Slicing Blade 11. Shredding Blade 12. Disc Holder...
Page 3
① Push Rod Grating Blade ⑨ ② Processing Bowl Cover Slicing Blade ⑩ ③ Chopping Blade unit ④ Drive Shaft Cover Shredding Blade ⑪ ⑤ Processing Bowl (1.2L) ⑥ Drive Shaft Disc Holder ⑫ ⑦ Motor unit ⑧ ON/OFF & Speed Rotary Knob...
Page 4
Warnings ATTENTION : Read this booklet carefully as it contains important instructions for a safe installation, use and maintenance. Important instructions to be kept for future reference. The following basic precautions should always be followed when using electrical appliances: 1. Read all instructions before using the appliance. The Appliance 2.
8. Only use original components & accessories provided by the manufacturer. Any non-original components & accessories (including, but not limited to, Push Rod, Grating / Slicing / Shredding Blades, Disc Holder, Chopping Blade unit, Drive Shaft & Cover, Processing Bowl & Cover, etc.) made by other manufacturers or by the same manufacturer but for other models of the same capacity or otherwise, may cause injuries to persons or damage to the appliance.
Page 6
b. Place the Motor unit on a flat, dry surface. Assemble the Push Rod, Grating / Slicing / Shredding Blades, Disc Holder, Chopping Blade unit, Drive Shaft & Cover, Processing Bowl & Cover to the Motor unit according to the instructions listed in the section (How to Use) below.
Page 7
• turn the ON/OFF & Speed Rotary Knob too hard so as to avoid any damage; • leave the appliance unsupervised during operation. 15. During operation, DO NOT touch the appliance with wet body parts, and it is recommended to have between you and the standing surface, an isolating element (for example, wearing shoes with rubber soles).
Page 8
How to use 1. Clean the Motor unit and accessories before using. Refer to the section “How to clean and maintain” immediately following this section. 2. Place the Base of the Motor unit on a flat, dry and heat-resistant surface. 3.
Page 9
17. To continue using the same ingredients, repeat steps 5 to 13. To continue using other ingredients, rinse the Processing Bowl Cover, Processing Bowl, Chopping Blade Unit or Disc Holder & attached blades and Drive Shaft Cover first and then repeat steps 5 to 13.
Page 10
How to clean 1. Turn the ON/OFF & Speed Rotary Knob to ‘0’ (OFF). Switch the wall switch OFF and unplug the power cable. 2. Before cleaning, please make sure the blades have stopped running. 3. Clean the Motor unit with a damp cloth. DO NOT immerse the Motor unit in water or other liquids, and avoid spraying water, in order to avoid damage or leakage.
PROBLEM SOLVING Fault symptom Cause analysis Troubleshooting The Processing Bowl Reconnect the Processing and the Motor unit are Bowl and the Motor unit not connected correctly After assembly, the Turn the motor shaft or Drive appliance does not The motor is damaged Shaft.
ENVIRONMENTAL TIP This appliance, along with all other electronic appliances, should, when it is no longer capable of functioning, be disposed with the least possible environmental damage according to the local regulations in your area. In most cases you can discard the appliance at your local recycling centre.
3. This warranty does not cover the repair or replacement of part/s damaged by misuse, accidents, negligence, alterations, or modifications in any way, or repairs done by any repair organisation without the prior consent of PowerPac Electrical Pte Ltd. 4. Repair and service are to be performed at: 5 Changi South Lane #03-01 Singapore 486045.
Page 14
In accordance with the terms and conditions of this limited warranty as stated above, PowerPac Electrical Pte Ltd, at its expense shall provide free services for the appliance within the warranty period from its date of purchase from our Authorised...
Need help?
Do you have a question about the PPBL775 and is the answer not in the manual?
Questions and answers