Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AW RPM68-2
Summary of Contents for AW RPM68-2
- Page 1 RPM68-2 Instruction Manual Bedienungsanleitung...
- Page 2 Important notes Wichtige Hinweise • Before operating this device for the first time, read • Bitte lesen Sie diese Anleitung vollständig, bevor Sie all instructions. dieses Gerät das erste Mal verwenden. • After unpacking the device, check for damage. If in •...
-
Page 3: Table Of Contents
Content Inhaltsverzeichnis Overview ................ Überblick ................. Features ................. Eigenschaften ..............Preparations ..............Vorbereitungen .............. Profiling a reed .............. Blatt hobeln ..............Adjust reed thickness ..........Blattdicke korrigieren ........... Change template ............Schablone wechseln ............. Change blade ..............Messer wechseln ............Change support plate ........... -
Page 4: Overview
Overview 1. Template 2. Reed support plate 3. Reed clamp 4. Blade 5. Copy roller 6. Thickness adjustment 7. Handle 8. Tool holder and marking aid 9. Transport lock Überblick 1. Schablone 2. Blattauflage 3. Blattspanner 4. Hobelmesser 5. Kopierrolle 6. -
Page 5: Features
Features • For reeds up to 68mm length and 14mm width (Eb clarinet, Bb clarinet, soprano saxophone). • Fine adjustment for reed thickness and left-right ratio. • Precision ball bearing guides. • Carbide blades with two cutting edges. • Maintenance-free and corrosion-protected. •... -
Page 6: Preparations
Preparations 1. Place the machine on a firm, level table. Optional (A): Attach table clamps to 2 corners of the profiler. 2. Loosen the locking screw (counterclockwise) and remove the transport lock. Vorbereitungen 1. Maschine auf einen festen, ebenen Tisch stellen. Optional (A): Tischklemmen an 2 Ecken des Handhobels anbringen. - Page 7 Preparations 3. Pull tools out of the tool holder. 4. Insert the tool holder into the hole of the base plate as a marking aid. Vorbereitungen 3. Werkzeuge aus dem Werkzeughalter ziehen. 4. Werkzeughalter als Markierhilfe in die Bohrung der Grundplatte stecken.
-
Page 8: Profiling A Reed
Profiling a reed 1. Place the blank centrally on the reed support. The line on the support indicates the position of the finished reed tip (after clipping). The blank tip must not be more than 2 mm above the line. 2. - Page 9 Profiling a reed 3. Push the carriage back and forth evenly by the handle. After each stroke, turn sideways a little further. Repeat the process until the blade no longer removes any chips. Caution: Do not press the carriage down! 4.
-
Page 10: Adjust Reed Thickness
Adjusting reed thickness • Correct reed thickness with Allen key (2.5mm). • The left and right reed sides can be adjusted independently of each other. • One graduation mark of the adjusting screws corresponds to 0.01mm reed thickness. • Mark your settings on the scale rings with a pen. Clockwise (+) >>>... -
Page 11: Change Template
Change template 1. Loosen (counterclockwise) screws (2x) with Allen key (2.5mm) and remove template. Clean the connection points. 2. Insert new template. Fasten screws (clockwise) again and tighten only slightly. To avoid damage to the reed support, the reed thickness should be set approx. 0.1mm (10 graduation marks) thicker (+) after each conversion. -
Page 12: Change Blade
Change blade 1. Loosen (counterclockwise) screws (2x) with Allen key (2mm) and remove blade from the side. Clean the connection points. 2. Insert new blade. Screw in screws (clockwise) again and tighten only slightly. Press the blade upwards while tightening. It must rest against the upper stop over its entire length. -
Page 13: Change Support Plate
Change support plate 1. Loosen (counterclockwise) screws (2x) with Allen key (2.5mm) and remove reed support plate. Clean the connection points. 2. Insert new reed support plate. Screw in screws (clockwise) again and tighten only slightly. To avoid damage to the reed support, the reed thickness should be set approx. - Page 16 Reed Making Tools c/o UHL Technik | Kreisstr. 10 | 89428 Syrgenstein | Germany www.aw-tools.com | info@aw-tools.com...
Need help?
Do you have a question about the RPM68-2 and is the answer not in the manual?
Questions and answers