Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ifs MC352-4P-2S-V2
Summary of Contents for ifs MC352-4P-2S-V2
- Page 1 MC352-4P-2S-V2 User Manual P/N 1041-EN • REV B • ISS 13JUL22...
- Page 2 Carrier, except where specifically permitted under US and international copyright law. Trademarks and IFS names and logos are a product brand of Aritech, a part of Carrier. patents Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.
- Page 3 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points.
-
Page 5: Table Of Contents
Switch Upper Panel 9 Wiring the Power Inputs 9 Wiring the Faulty Alarm Contact 10 Grounding the Device 10 Installation 12 Mounting the DIN rail 12 Mounting the Wall-mount Plate 13 Product specifications 14 Customer Support 15 MC352-4P-2S-V2 User Manual... -
Page 6: Important Information
SOLD OR LICENSED BY CARRIER, MAY BE HACKED, COMPROMISED AND/OR CIRCUMVENTED AND CARRIER MAKES NO REPRESENTATION, WARRANTY, COVENANT OR PROMISE THAT ITS PRODUCTS (INCLUDING SECURITY PRODUCTS), SOFTWARE, SERVICES OR OTHER OFFERINGS WILL NOT BE HACKED, COMPROMISED AND/OR CIRCUMVENTED. MC352-4P-2S-V2 User Manual... -
Page 7: Warranty Disclaimers
SECURITY PRODUCTS), SOFTWARE, SERVICE OR OTHER OFFERING MAY NOT BE HACKED, COMPROMISED AND/OR CIRCUMVENTED. CARRIER DOES NOT WARRANT THAT ANY PRODUCT (INCLUDING SECURITY PRODUCTS), SOFTWARE OR SERVICE MANUFACTURED, SOLD OR LICENSED BY CARRIER WILL PREVENT, OR IN ALL CASES PROVIDE ADEQUATE WARNING MC352-4P-2S-V2 User Manual... -
Page 8: Intended Use
Note: Note messages advise you of the possible loss of time or effort. They describe how to avoid the loss. Notes are also used to point out important information that you should read. MC352-4P-2S-V2 User Manual... -
Page 9: Package Contents
Package contents Thank you for purchasing the IFS Industrial 4-Port 10/100/1000T 802.3at PoE + 2-Port 100/1000X SFP Ethernet Switch, MC352-4P-2S-V2. In the following sections, the term “Industrial Gigabit PoE+ Switch” means the MC352-4P-2S-V2. Open the box of the Industrial Gigabit PoE+ Switch and carefully unpack it. The box should contain the following items: •... -
Page 10: Hardware Introduction
The front panel of the Industrial Gigabit PoE+ Switch consists of Ethernet interfaces and LED indicators. Front View Figure 1: MC352-4P-2S-V2 Front View PoE Power Usage LED The front panel of the Industrial Gigabit PoE+ Switch has four LEDs that indicate... - Page 11 The following figure shows the redundant functions. Figure 2: Redundancy Behavior Topology Note: Using the Redundant mode, port 5 is defined as Primary Port and port 6 as Backup Port. MC352-4P-2S-V2 User Manual...
-
Page 12: Led Definition
85 < X < 90, 90W LED flash; X >= 90, 90W LED light; 100 < X < 115, 120W LED flash; 115 < X < 120, 120W LED flash fast; X >= 120, 120W LED light. MC352-4P-2S-V2 User Manual... -
Page 13: Switch Upper Panel
1. Insert positive and negative DC power wires into contacts 1 and 2 for POWER 1, or contacts 5 and 6 for POWER 2. V2+ V2- 2. Tighten the wire-clamp screws for preventing the wires from loosening. MC352-4P-2S-V2 User Manual... -
Page 14: Wiring The Faulty Alarm Contact
1. The wire gauge for the terminal block should be in the range of 12 ~ 24 AWG. 2. Alarm relay circuit accepts up to 24 V, max. 1 A currents. Grounding the Device The device must be correctly grounded to avoid serious damage. MC352-4P-2S-V2 User Manual... - Page 15 Note: EMD (Lightning) DAMAGE IS NOT CONVERED UNDER WARRANTY. MC352-4P-2S-V2 User Manual...
-
Page 16: Installation
This section describes how to install the Industrial PoE+ Switch on the DIN rail and wall. Note: The following pictures show how to install the device. However, the device in the picture is not MC352-4P-2S-V2. Mounting the DIN rail The DIN rail bracket is screwed on the Industrial PoE+ Switch when shipped. You need an Industrial PoE+ Switch when replacing the wall-mount application with DIN rail application. -
Page 17: Mounting The Wall-Mount Plate
3. Use the screws to attach the wall-mount plate on the Industrial PoE+ Switch. 4. Use the hook holes at the corners of the wall-mount plate to hang the Industrial PoE+ Switch on the wall. 5. To remove the wall-mount plate, reverse the steps above. MC352-4P-2S-V2 User Manual... -
Page 18: Product Specifications
8.93 Mpps @ 64 bytes (packet per second) Address Table 4 K entries Buffer Memory 1 M bits on-chip buffer memory Jumbo Frame 9 Kbytes Back pressure for half duplex Flow Control IEEE 802.3x pause frame for full duplex MC352-4P-2S-V2 User Manual... -
Page 19: Customer Support
Storage: -40 to +75°C Operating: 5 to 90% Humidity (non-condensing) Storage: 5 to 90% Customer Support If you need support information, please contact our support team, whose contact details can be found on our website: EMEA: https://firesecurityproducts.com Australian/New Zealand: https://firesecurityproducts.com.au/ MC352-4P-2S-V2 User Manual...