Page 1
POE304-MS PoE Injector User Manual P/N 1073475-EN • REV C • ISS 06OCT22...
Page 2
Trademarks and patents IFS and associated names and logos are a product brand of Aritech, a part of Carrier. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.
Page 3
Product documentation Please consult the following web link to retrieve the electronic version of the product documentation. The manuals are available in several languages.
COVENANT OR PROMISE THAT ITS PRODUCTS (INCLUDING SECURITY PRODUCTS), SOFTWARE, SERVICES OR OTHER OFFERINGS WILL NOT BE HACKED, COMPROMISED AND/OR CIRCUMVENTED. CARRIER DOES NOT ENCRYPT COMMUNICATIONS BETWEEN ITS ALARM OR OTHER CONTROL PANELS AND THEIR WIRELESS OUTPUTS/INPUTS INCLUDING POE304-MS PoE Injector User Manual...
Page 7
CARRIER DOES NOT WARRANT THAT ANY PRODUCT (INCLUDING SECURITY PRODUCTS), SOFTWARE OR SERVICE MANUFACTURED, SOLD OR LICENSED BY CARRIER WILL PREVENT, OR IN ALL CASES PROVIDE ADEQUATE WARNING OF OR PROTECTION FROM, BREAK-INS, BURGLARY, ROBBERY, FIRE, OR OTHERWISE. POE304-MS PoE Injector User Manual...
Page 8
Note: Note messages advise you of the possible loss of time or effort. They describe how to avoid the loss. Notes are also used to point out important information that you should read. POE304-MS PoE Injector User Manual...
Chapter 1 Introduction The description of the IFS POE304-MS model is as follows: Single-port 802.3af/at/bt PoE injector, 10/100/1000 Mbps, 60 W PoE power budget. Unless specified, the term “PoE injector” mentioned in this user manual refers to the POE304-MS.
Page 10
PoE injector function as PoE (Data and Power) output. The "PoE OUT" port is also the power injector to transmit DC voltage over the Cat. 5/5e/6 cable and transfer data and power simultaneously between the PSE and PD. POE304-MS PoE Injector User Manual...
IEEE 802.3af is 15.4 W, and in IEEE 802.3at is 30 W. 2. PD (Powered Device) is a PoE-enabled terminal by PSE and thus consumes energy. Examples include PoE IP phones, PoE IP cameras, and PoE wireless access points. POE304-MS PoE Injector User Manual...
Pair 1 End-span 1/2(-), 3/6(+); Power Pin Assignment Pair 1 Mid-span 4/5(+), 7/8(-) DC 54 V / 60 W PoE via 4-pair PoE Power Output Budget DC 54 V / 30 W PoE via 2-pair POE304-MS PoE Injector User Manual...
Page 13
IEEE 802.3bt 4-pair Power over Ethernet (pre-standard) IEEE 802.3at Power over Ethernet Plus IEEE 802.3af Power over Ethernet Environment Temperature: 0 to 50°C Operating Relative Humidity: 5 to 90% (non-condensing) Temperature: -10 to 70°C Storage Relative Humidity: 5 to 90% (non-condensing) POE304-MS PoE Injector User Manual...
Blinking: indicates the PoE usage is 30 to 39 W. 40 W Orange Lit: indicates the PoE usage is 40 to 49 W. Blinking: indicates the PoE usage is 50 to 59 W. 60 W+ Orange Lit: indicates the PoE usage is at maximum. POE304-MS PoE Injector User Manual...
Page 16
802.3af/at/bt standard and their unique electrical signatures so that the PoE Legacy injector can provide power to those PD devices. Legacy mode will handshake to check if this connected device is a PoE device first. If handshaking fails, forced output power is used. POE304-MS PoE Injector User Manual...
802.3af/at/bt end-nodes such as PTZ (Pan, Tilt & Zoom) network cameras, PTZ speed domes, color touch screens, Voice over IP (VoIP) telephones, and multi- channel wireless LAN access points that support IEEE 802.3af/at/bt In-line PoE ports. POE304-MS PoE Injector User Manual...
PoE injector and PD. 6. After the PoE extender detects the existence of an IEEE 802.3af/at device, the “PoE OUT” LED indicator illuminates steadily ON to indicate that it is providing power. POE304-MS PoE Injector User Manual...
Page 19
PoE OUT LED indicator of the PoE extender does not illuminate steadily. 2. According to the IEEE 802.3af/at standard, the PoE extender will not inject power to the cable if the connected device doesn’t support the IEEE 802.3af/at standard. POE304-MS PoE Injector User Manual...
The standard RJ45 receptacle/connector: There are eight wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and the color of the straight cable and crossover cable connection: POE304-MS PoE Injector User Manual...
Page 21
7 = White / Brown SIDE 2 8 = Brown 8 = Brown Ensure that connected cables are with the same pin assignment and color as the above diagram before deploying the cables into the network. POE304-MS PoE Injector User Manual...