Advertisement
TESTER
REMOTE
NOTE: No user-serviceable parts.
PROPERLY WIRED T568A
PROPERLY WIRED T568B
NOTE - RJ11/RJ12 TEST IS FOR STRAIGHT THROUGH WIRING. CROSS OVER WIRING WILL DISPLAY A FAIL RESULT
T568A CABLE WITH SHORT AND OPEN
The 1-2 pair of pins are shorted together and the 7-8 pair is open. The SHORT LED and OPEN LED will illuminate simultaneously.
T568A CABLE WITH A MISWIRE AND UNRECOGNISED CONTINUITY
Pins 1 and 2 on the Near end are connected to Pins 2 and 1 on the Far End.
The Klein Tools LAN Explorer™ is a portable voice and data cable tester. It tests and troubleshoots RJ45, RJ11 and RJ12 terminated cables and patch cords.
Specifications subject to change.
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
To ensure safe operations, follow these instructions. Failure to observe these warnings can result in fire, electric shock, severe injury or death.
Warning or Caution | Wear approved eye protection | NOT insulated - will NOT protect against electric shock | Read all instructions |
NOTE: See FIG. 1 below for examples of correctly and incorrectly wired connectors.
PASS INDICATORS
Will illuminate if the cable is properly wired. For RJ45, the 4 pairs are wired according to the T568A/568B data cable standards or if cable is wired straight through on RJ11 or RJ12 terminated plugs.
FAULT INDICATORS
MISWIRE: Illuminates if the cable is not wired to one of the cabling standards shown below, or if the conductor wire order on the near end does not match the conductor wire order on the opposite end, i.e. if Pin 1 on near end is wired to Pin 2 on the far end.
OPEN: Illuminates if one or more of the conductor wires on the near end are not terminated properly on the far end, or if any of the near-end contact pins are not properly terminated.
SHORT: Illuminates when two or more conductor wires make contact with each other.
SHIELDED INDICATOR
Illuminates when a shielded (ground wire or foil) data cable is properly connected at both ends, either by ground wire or by foil.
NOTE:
NOTE: A Cross-Over Cable, RJ45 or RJ11/12, will flash MISWIRE and PASS simultaneously. On an RJ12-terminated wire with Pin 1 and 6 open faults, "RJ11 PASS" will be the response.
POWERING ON AND OFF / TESTING A CABLE
The LAN Explorer™ has a single button to start a test. When powered off, a short press of the Test button causes the LAN Explorer™ to turn on, and a cable test to be executed. See INDICATORS section. The results are displayed for 30 seconds before powering off. If another short press occurs before the 30 second time-out, another test cycle will begin, followed by another 30 second time-out.
The LAN Explorer™ will automatically power off if there is no test result change for 30 seconds.
To manually power off the LAN Explorer™, press the Test Button for 2 seconds.
BATTERY REPLACEMENT
When the Low Battery indicator blinks or tester does not turn on, the battery must be replaced.
Turn tester off and disconnect any cables. Wipe with a clean, dry lint-free cloth.
Do not use abrasive cleaners or solvents.
Remove the battery when the unit is not in use for a prolonged period of time. Do not expose to high temperatures or humidity. After a period of storage in extreme conditions exceeding the limits mentioned in the General Specifications section, allow the unit to return to normal operating conditions before using.
DISPOSAL RECYCLE
Do not place equipment and its accessories in the trash. Items must be properly disposed of in accordance with local regulations.
CUSTOMER SERVICE
KLEIN TOOLS, INC.
450 Bond Street Lincolnshire, IL 60069
1-800-553-4676
customerservice@kleintools.com
www.kleintools.com
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Klein Tools Lan Explorer VDV526-100 - Cable Tester With Remote Manual
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the Lan Explorer that isn't answered in the manual? Leave your question here.