Panasonic PT-DW5100 Specifications
  1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. Projector
  5. PT-DW5100
  6. Specifications
Panasonic PT-DW5100 Specifications

Panasonic PT-DW5100 Specifications

Panasonic pt-dw5100: user guide
Hide thumbs Also See for PT-DW5100:
Table of Contents

Advertisement

Quick Links

P ro d u c t N u m b e r :
P ro d u c t N a m e :
As of May 2007. Specifications subject to change without notice.
S
P
E
C
PT-DW5100/DW5100L
DLP
™
Projectors
F
I
L
E
The PT-DW5100L is not equipped with a lens.
< 1 >

Advertisement

Table of Contents
loading

Related Manuals for Panasonic PT-DW5100

Summary of Contents for Panasonic PT-DW5100

  • Page 1 PT-DW5100/DW5100L P ro d u c t N u m b e r : P ro d u c t N a m e : As of May 2007. Specifications subject to change without notice. The PT-DW5100L is not equipped with a lens.

  • Page 2: Specifications

    Main Unit Power supply: North America: Europe: Power consumption: North America: Europe: DLP™ chip: Panel size: Display method: Pixels: Lens: PT-DW5100: PT-DW5100L: Lamp: Screen size: Brightness* Center-to-corner uniformity* Contrast* Resolution: Scanning frequency: RGB: S-Video/Video: Optical axis shift: Keystone correction range:...
  • Page 3 Weights and dimensions shown are approximate. Specifications subject to change without notice. *1 Values indicate overall average values of the product at the time of shipment and are stated based on JIS X 6911:2003 Data Projector Specification Sheet Format. Measurement method and conditions are based on Appendix 2.
  • Page 4 T, M, D, S data 2- T, M, D, S data 2+ T, M, D, S data 2 shield DDC clock DDC clock As of May 2007 PT-DW5100/DW5100L 1 Video input 2 S-Video input 3 RGB 1 input 4 RGB 2 Input 5 DVI-D input...

  • Page 5: Standard Setting-Up Position

    The ET-DLE050 has a fixed short-focus lens. Therefore, the lens shift function provided in the main unit cannot be used. If the lens shift function is used, the corners of images may not be displayed or images may remain out of focus in some cases. As of May 2007 PT-DW5100/DW5100L (10-3/32˝) (3-15/16˝) (15-3/4˝) Attachment plate (10-9/32˝)
  • Page 6 • For the ET-DLE050, the height from the edge of the screen to the center of the lens (H) is 1/2 of the screen height. • The brightness varies depending on the zoom setting. As of May 2007 PT-DW5100/DW5100L Distance to screen (L) Zoom...

  • Page 7: Projection Distance For 16:9 Aspect Ratio Screen

    • The height of images from 4:3 aspect ratio sources is slightly larger than that of images from 16:9 sources. If images from 4:3 sources do not fit the screen, set the aspect ratio to "S4:3". As of May 2007 PT-DW5100/DW5100L Distance to screen (L) Zoom...

  • Page 8: Calculation Of The Projection Distance

    • When an SXGA signal is input, the left and right edges of the image are blanked, and the image is projected at a screen aspect ratio of 5:4. • The brightness varies depending on the zoom setting. As of May 2007 PT-DW5100/DW5100L L (m) = (diagonal screen size in inches) x 0.0300 - 0.0452 L (m) = (diagonal screen size in inches) x 0.0404 - 0.0478 L (m) = (diagonal screen size in inches) x 0.0402 - 0.0650...
  • Page 9 Optical axis shift function allows to shift the position of a projected image as shown below. (Width of projected image) 0.1H Installable angle Install the projector at an angle within the range shown below. • Vertical direction The projector may be installed at a vertical angle of 360°. As of May 2007 PT-DW5100/DW5100L 0.1H...

  • Page 10: List Of Compatible Signals

    NOTE: The native resolution of this projector is 1,280 x 768 pixels. If the display resolution of the input signal is different from the native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution.
  • Page 11 • It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this occurs, wait for 60 seconds, then try sending or receiving again. • When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector before sending the next command.
  • Page 12 1 Do not send PON, POF, OSH, or OLP commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replacement cycle. 2 When a command that cannot be executed during standby mode is sent, the projector will send an ER401 command in reply.
  • Page 13 1 p1p2p3p4: Celsius (°C), p5p6p7p8: Fahrenheit (°F) Day of week: Monday = 1, Tuesday = 2, ... Sunday = 7 Set the date and time to UTC (universal time coordinated). As of May 2007 PT-DW5100/DW5100L Function Callback Main power status...

  • Page 14: Parameter Format

    <lamp power> <acctch> <color temp> <date> <time> NOTE: If a wrong command is received, the projector will send an ER401 command to the computer. Command example To set the on-screen display off, send the command as shown below. ADZZ Start ID Address NOTE: When sending commands without parameters, a colon (:) is not necessary.
  • Page 15 * Even when the ambient temperature near the intake opening is 40°C/104°F or lower, an accumulation of hot air inside the cabinet may cause the protective circuit to activate and shut down the projector. Please give ample consideration to the design with regard to ambient temperature conditions.

This manual is also suitable for:

Pt-dw5100l

Table of Contents