Table of Contents
Advertisement
Video Channel Set
Video channel (RF output channel) is the channel on which your
TV receives picture and sound signals from the recorder through
the RF cable.
Perform the following steps only if —
— Video Chennel Set has not been done correctly by the Auto Set
Up function (
4),
— you set up the recorder's tuner by Preset Download (
instead of using the Auto Set Up function,
— interference appears in the TV picture after you have moved to
a different area or a new station has started broadcasting in your
area,
— you change the connection between your recorder and TV
from RF connection to AV connection, or vice versa.
If you have connected the recorder to your TV via the AV
connection, set the video channel to off.
If you have connected the recorder to your TV via the RF
connection, set the correct video channel.
● Make sure the recorder's power is off and there is no cassette
inserted in the recorder.
A
Access Video Channel Set mode
Hold down 0 on the recorder until the
display panel shows the following.
B
Set RF output system
The blinking number on the display
indicates the RF output system of your
country. Press rt to set to "1" or "2", then press OK. (1: B/G
2: D/K)
Major Countries
Austria, Denmark, Finland, Holland, Italy,
Norway, Spain, Switzerland, Sweden,
Germany, Egypt
China, Mongolia, Rumania, Bulgaria, Czech
Rep., Slovakia, Hungary, Poland, Russia
C
Set video channel
With AV connection
Press PR – until the display panel shows
"1 – –" (or "2 – –").
● Now the video channel is set to off.
With RF connection
Press PR + or – to set the video channel to a vacant position
between 22 and 69 which is not occupied by any local station in
your area.
(Example) If channel 50 is available in your
area, set the video channel to 50.
Then, set your TV to UHF channel 50.
● If the two vertical white bars appear
clearly on the screen as shown on the right, go
to step 4 4 4 4 .
● If the two vertical white bars do not appear
clearly, re-set the video channel to another
vacant position and try again.
D
Exit Video Channel Set mode
Press OK.
With AV connection
To view picture signals from the recorder, set your TV to its AV
mode.
With RF connection
The channel on which the two vertical white bars appear
clearly is your video channel. To view picture signals from the
recorder, set your TV to the video channel.
Specifications
GENERAL
Power requirement
Power consumption
4)
Power on
Power off
Temperature
Operating
Storage
Operating position
Dimensions (W x H x D) : 400 mm x 94 mm x 270 mm
Weight
Format
Maximum recording time
(SP)
(LP)
VIDEO/AUDIO
Signal system
Recording system
Signal-to-noise ratio
TV System
Horizontal resolution
Frequency range
B/G
Normal audio
Hi-Fi audio
Input/Output
D/K
TUNER/TIMER
TV channel storage
capacity
Tuning system
Channel coverage
VHF
UHF
Aerial output
Memory backup time
ACCESSORIES
Provided accessories
Optional accessories
Specifications shown are for SP mode unless specified otherwise.
E. & O.E. Design and specifications subject to change without
notice.
— 16 —
: AC 220 V – 240 V
d
, 50 Hz/60 Hz
: 15 W
: 3.3 W
: 5°C to 40°C
: –20°C to 60°C
: Horizontal only
: 3.1 kg
: VHS PAL standard
: 240 min. with E-240 video cassette
: 480 min. with E-240 video cassette
: PAL-type colour signal and CCIR
monochrome signal, 625 lines
50 fields
: DA4 (Double Azimuth) head helical
scan system
: 45 dB
: 250 lines
: 70 Hz to 10,000 Hz
: 20 Hz to 20,000 Hz
: 21-pin SCART connectors:
IN/OUT x 1, IN/DECODER x 1
RCA connectors:
VIDEO IN x 1, AUDIO IN x 1,
AUDIO OUT x 1
: 99 positions (+AUX position)
: Frequency synthesized tuner
: 47 MHz – 89 MHz/
104 MHz – 300 MHz/
302 MHz – 470 MHz
: 470 MHz – 862 MHz
: UHF channels 22 – 69 (Adjustable)
: Approx. 10 min.
: RF cable,
Infrared remote control unit,
"R6" battery x 2
: Satellite Controller RM-SD1
Advertisement
Table of Contents
