Table of Contents
Advertisement
Quick Links
Controller for LED Illumination
VLC-2430-4
Operation Manual
Thank you for purchasing a VAL product.
To use this LED controller with optimum performance and safety,
please read this manual thoroughly before starting operation.
Keep this manual for the whole product lifetime.
The following warning symbols are used in this manual.
Be sure to fully understand the contents.
WARNING
A warning denotes a hazard that can cause severe injury or death.
CAUTION
A caution denotes a hazard that can cause injury or damage of equipment.
Advertisement
Table of Contents
Related Manuals for VAL VLC-2430-4
Summary of Contents for VAL VLC-2430-4
- Page 1 Controller for LED Illumination VLC-2430-4 Operation Manual Thank you for purchasing a VAL product. To use this LED controller with optimum performance and safety, please read this manual thoroughly before starting operation. Keep this manual for the whole product lifetime.
-
Page 2: Safety Regulations
１．Safety regulations WARNING Do not open the chassis to avoid electric shock. High-voltage parts are inside. Use appropriate DC power only. 1) DC24V：Input terminal board of the controller M3 terminal board. : Crimp Terminal on the connected side M3 round crimp terminal. Earth ground the product. -
Page 3: General Description
２．General Description VLC-2430-4 are a controller for VAL series or LED lighting unit made by VS Technology (Thailand) Co., Ltd. It can be used with input voltage range with DC24V and output wattage maximum totally 30W with 1CH and 2CH and 3CH and 4CH. - Page 4 ５．Control with External Signals Use output signal cable of 3m or shorter. Do not apply too high current and voltage. CAUTION Do not use external connector except SELV circuit with reinforced insulation or a circuit with double insulation. Connector Communications Specifications Signal Communications protocol EIA-232-D...
- Page 5 Setting the lighting mode to @00S0400B8CRLF @00O0050CRLF @00N0300B2CRLF Strobe Mode at 200μs for CH2 of the VLC-2430-4 that the ID set to 00. -To set ON/OFF Signal in ON/OFF mode Specify the ID and the channel, and set ON/OFF signal. Setting example...
-
Page 6: Specification
６．Specification Model VLC-2430-4 Input Voltage DC 24V (rated) ±10% 50/60Hz Power Consumption DC 24V/1.5A Rated output voltage 4 Channels DC24V (between output and GND) Rated output current 1.25A (Total for 4 channels) DC input 3M round crimp terminal is are recommend to connect to the terminal block Input Connectors SMP-03V-BC (JST) 1:output＋... - Page 7 ７．Dimensions and Functions ① Intensity Volume Knob For digital control ② Digital Display Display the setting of the light intensity or the setting of the lighting mode. ③ Channel Selection Switch Selects CH1, CH2, CH3, CH4. CH1 lit: Lit when changing settings for Light Unit connected to output connector CH1. CH2 lit: Lit when changing settings for Light Unit connected to output connector CH2.
- Page 8 CH4 5 to 9 No used COMMON+ Yellow/Black *External Trigger Signal Connection Example VLC-2430-4 Exte rn al Circ u its VLP- 2 4 3 0 - 4 Co n tro l U n it Transistor (NPN) 7.5kΩ open collector...
- Page 9 *Setting Procedures With external trigger input connectors pins 1 to 4, select the channels (CH1 to CH2 to CH3 to CH4) where you want to input an external trigger, and input trigger. Trigger signals are input from the external trigger input connector in ON/OFF Mode and Strobe Mode in both Internal Mode or External Mode.
-
Page 10: Optional Accessories
９．Optional Accessories *External Control Cable Model: VL-EXCB1-3 Connector: XN2A-1470 (Manufactured by OMRON) *External Trigger Input Cable Model: VL-EXCB2-3 Connector: XG4M-1030-T (Manufactured by OMRON) 10．Warranty ・Duration of warranty The duration of the product warranty shall be two years from the day of product delivery. ・Extent of warranty If a fault or defect attributable under normal use during the warranty period, VS Technology (Thailand) Co., Ltd.
Need help?
Do you have a question about the VLC-2430-4 and is the answer not in the manual?
Questions and answers