Do you have a question about the KX-TGDA59C and is the answer not in the manual?
Questions and answers
Richard Mills
April 3, 2025
The screen is blank and manual calls for a reset but no reset button visible in battery compartment
1 comments:
Mr. Anderson
April 3, 2025
To reset the Panasonic KX-TGDA59C when the screen is blank and there is no reset button in the battery compartment, try the following steps:
1. Remove the batteries from the handset. 2. Wait for about 1 minute to allow the handset to fully power down. 3. Reinsert the supplied rechargeable Ni-MH AAA batteries, ensuring correct polarity. 4. Place the handset on the charger and confirm that “Charging” appears on the screen. 5. Wait until the screen becomes active. If the screen remains blank, ensure the batteries are charged and correctly installed.
If the screen does not respond after following these steps, the handset may require service.
Page 1
Installation Manual Additional Digital Cordless Handset KX-TGDA59C Model No. Thank you for purchasing a Panasonic product. This unit is an additional handset compatible with the following series of Panasonic Digital Cordless Phone: KX-TGD590 (The corresponding models are subject to change without notice.) You must register this handset with your base unit before it can be used.
Confirm that smoke has stopped emitting and contact us by visiting our Support page: www.panasonic.ca/english/support Installation R To prevent the risk of fire or electrical shock, do not expose the product to rain or any type of moisture. For assistance, visit www.panasonic.ca/english/support 2911_TGDA59C (en-en)_ver002.pdf 2 12/9/2016 8:02:02 AM...
Important safety instructions When using your product, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: For assistance, visit www.panasonic.ca/english/support 2911_TGDA59C (en-en)_ver002.pdf 3 12/9/2016 8:02:02 AM...
Compliance with TIA-1083 standard Telephone handsets identified with this logo have reduced Compatible with noise and interference when used with T-Coil equipped Hearing Aid T-Coil hearing aids and cochlear implants. TIA-1083 For assistance, visit www.panasonic.ca/english/support 2911_TGDA59C (en-en)_ver002.pdf 4 12/9/2016 8:02:02 AM...
Page 5
MbN: Select the desired setting. a MSAVEN a MOFFN Important: R Use the supplied rechargeable batteries. For replacement, we recommend using the Panasonic rechargeable batteries noted in the base unit’s operating instructions. R USE ONLY rechargeable Ni-MH batteries AAA (R03) size ( R Do NOT use alkaline/manganese/Ni-Cd batteries.
Page 6
Place the handset on the base unit or charger, then wait until a long beep sounds and is displayed. Note: R If an error tone sounds, or if is displayed, register the handset according to the base unit’s operating instructions. For assistance, visit www.panasonic.ca/english/support 2911_TGDA59C (en-en)_ver002.pdf 6 12/9/2016 8:02:02 AM...
R For body-worn operation, the handset must be used only with a non-metallic accessory. Use of other accessories may not ensure compliance with ISED RF exposure requirements. For assistance, visit www.panasonic.ca/english/support 2911_TGDA59C (en-en)_ver002.pdf 7 12/9/2016 8:02:02 AM...
This warranty is given only to the original purchaser, or the person for whom it was purchased as a gift, of a Panasonic brand product mentioned above sold by an authorized Panasonic dealer in Canada and purchased and used in Canada, which product was not sold “as is”, and which product was delivered to you in new condition in the original packaging.
Need help?
Do you have a question about the KX-TGDA59C and is the answer not in the manual?
Questions and answers
The screen is blank and manual calls for a reset but no reset button visible in battery compartment
To reset the Panasonic KX-TGDA59C when the screen is blank and there is no reset button in the battery compartment, try the following steps:
1. Remove the batteries from the handset.
2. Wait for about 1 minute to allow the handset to fully power down.
3. Reinsert the supplied rechargeable Ni-MH AAA batteries, ensuring correct polarity.
4. Place the handset on the charger and confirm that “Charging” appears on the screen.
5. Wait until the screen becomes active. If the screen remains blank, ensure the batteries are charged and correctly installed.
If the screen does not respond after following these steps, the handset may require service.
This answer is automatically generated