MULTIQUIP Mikasa MT-85H Operation Manual

Tamping rammer

Hide thumbs

Table Of Contents

Quick Links

Download this manual

OPERATION MANUAL

SERIES

MODEL MT-85H

TAMPING RAMMER

(ROBIN EC12-G ENGINE)

Revision #9 (10/29/20)

To find the latest revision of this publication or

associated parts manual, visit our website at:

www.multiquip.com

THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.

Table of Contents

Need help?

Do you have a question about the Mikasa MT-85H and is the answer not in the manual?

Questions and answers

Summary of Contents for MULTIQUIP Mikasa MT-85H

Page 1 OPERATION MANUAL SERIES MODEL MT-85H TAMPING RAMMER (ROBIN EC12-G ENGINE) Revision #9 (10/29/20) To find the latest revision of this publication or associated parts manual, visit our website at: www.multiquip.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
Page 2 PAGE 2 — MT-85H — OPERATION MANUAL — REV. #9 (10/29/20)
Page 3: Table Of Contents
TABLE OF CONTENTS MT-85H Table Of Contents ..........3 Rules For Safe Operation ........4-5 Operation and Safety Decals ........ 6 General Information ..........7 Specification ............8 Controls and Components ........9 Operation ............10-11 Maintenance ............12 Troubleshooting Guide ........13-14 NOTE Specification and part number are subject to change without...
Page 4: Rules For Safe Operation
■ NEVER use accessories or attachments, which are not equipment is for industrial use only. recommended by Multiquip for this equipment. Damage to The following safety guidelines should always be used when the equipment and/or injury to user may result.
Page 5 ■ NEVER use accessories or attachments, which are not ■ Always know the location of the nearest fire extinguisher recommended by Multiquip for this equipment. Damage to and first aid kit . Know the location of the nearest telephone. the equipment and/or injury to user may result.
Page 6: Operation And Safety Decals
OPERATION AND SAFETY DECALS PAGE 6 — MT-85H — OPERATION MANUAL — REV. #9 (10/29/20)
Page 7: General Information
To maintain optimum performance, proper operation and service are essential. Construction of Tamping Rammer The Mikasa MT-85H is equipped with an air cooled, two cycle gasoline engine. Transmission of the power takes place by increasing the engine speed to engage the centrifugal clutch.
Page 8: Specification
MT-85H — SPECIFICATIONS . S . r t e ) c i l l a . n i l l a e z i l b / t u l c i t f i r t i t a s b l - r i o r t...
Page 9: Controls And Components
16. Spark Plug – Provides spark to the ignition system, excess fuel is present in the carburetor, or crankcase. L1. A Returned Material Authorization must be approved by Multiquip prior to shipment. A copy of the Authorization must replace with engine manufactures recommended type accompany the shipment to the designated Warehouse.
Page 10 MT-85H — OPERATION Inspection This section is intended to assist the operator with the initial start-up of the MT-85H Tamping Rammer. It extremely important 1. Check all nuts, bolts fasteners for tightness. Retighten as that this section be read carefully before attempting to operate necessary.
Page 11: Operation
MT-85H — OPERATION 2. Close the choke lever Figure 3 and move the throttle lever to the "Full Open" position. Turning the choke lever 90 degrees clockwise closes the choke . In cold weather, start the unit with choke fully closed. In warm weather or when the engine is warm, the unit can be started with choke halfway or completely open.
Page 12: Maintenance
MT-85H — MAINTENANCE ■ The air cleaner on the engine side will hardly be Maintenance contaminated, if it is, however after cleaning the element Perform the scheduled maintenance procedures as indicated: with kerosene, dip it in mixed oil consisting of 3 parts of DAILY gasoline and 1 part of engine oil.
Page 13: Troubleshooting Guide
MT-85H — TROUBLESHOOTING GUIDE c i f t l u i t i i r b i t i t i s o i t o i t l i a l l i e t i l i a c r i i t c .
Page 14 MT-85H — TROUBLESHOOTING GUIDE ENGINE ENGINE ENGINE ENGINE ENGINE n i t i t a f s i s u j e r r v e l . r e i r p c e f v i t c a l o i t i o i t u l f...
Page 15 MT-85H — NOTE PAGE MT-85H — — PAGE 15 OPERATION MANUAL — REV. #9 (10/29/20)
Page 16 © COPYRIGHT 2020, MULTIQUIP INC. Multiquip Inc , the MQ logo and the Mikasa logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property of their respective owners and used with permission.

This manual is also suitable for:

Mikasa series