palmOne LifeDrive Mobile Manager Quick Start

Start here
Here's what you'll do with this guide:
• Charge and set up your device.
®
• Install Palm Desktop software and other software for synchronizing,
moving files, and more.
• Synchronize your device with your computer.
Stylus
USB sync cable
™
LifeDrive mobile manager
from palmOne
Software installation CD
IMPORTANT! Already use a palmOne ™ device?
Upgrading? Before you start step 3, read this:
Your new device uses a different file structure from the one on your
current handheld. Because of this, some third-party applications
may not work correctly on your new device. When you synchronize
using your existing username, any third-party applications that may
not work correctly on your device do not install. All of your personal
(PIM) information–calendar events, contacts, tasks, and memos–is
installed to your device.
What about the third-party applications that were not installed?
Check each third-party application's website for news about an
updated version that works on your new device. Be sure to install
only applications that specifically state they are compatible with
your device. For more information on third-party applications and
the new file structure, go to www.palmOne.com.

Troubleshooting

Support information is also available at www.palmOne.com/support.
IMPORTANT! Take care of your device
• Be especially careful with your device when the amber indicator light is flashing.
This means that the hard drive is processing information, and you could lose
some or all of the information on the drive if you shake or drop the device.
• Do not open your device for any reason. If you attempt to remove the hard
drive, the warranty is voided.
• Do not drop, bang, shake, or cause any strong impact to your device.
Your device does not turn on or does not respond when you tap it
1. Try turning it on by pressing one of the quick buttons on the front panel.
2. Do a soft reset. Press the reset button on the bottom of the device with the
tip of the stylus.
3. Make sure the AC charger is fully connected to the device or the sync cable
and to a working outlet. Charge for another three full hours.
Palm Desktop Installer does not start when you put the CD into the drive
Windows
1. Click the Start button and select Run.
2. Click Browse to locate the drive that contains the CD that came with your device.
3. Double-click autorun.exe on the CD.
Mac
1. Double-click the CD icon on the Mac desktop.
2. Double-click palmOneDesktop.pkg.
1
Connect and charge
a. Plug the sync cable into your device and into a USB port on the back of
your computer.
b. Plug the AC charger into the Multi-connector on the sync cable and
into an outlet.
c. Charge for three hours. Be sure to fully charge your device before going
on to the next step.
Pouch
AC charger
3
Install software
To install Palm Desktop software, the LifeDrive Manager application, and
other important software, insert the CD into your computer's CD drive.
Windows
Follow the installation instructions
that appear on your computer
screen.
Synchronization does not begin
Be sure the sync cable is plugged into your device and into a USB port on the back of
your computer.
Check your computer:
Windows
1. Make sure the HotSync
your screen.
If not:
a. Click the Start button, and then select Programs.
b. Select palmOne, and then select HotSync Manager.
2. Check the connection type:
a. Disconnect and then reconnect the sync cable.
b. Make sure there is a checkmark next to Local USB.
If there is not, click Local USB.
Mac
1. Make sure HotSync Manager is enabled:
a. Double-click the HotSync Manager icon in the Palm folder.
b. In the HotSync Controls tab, click Enabled.
2. Make sure the USB connection is working:
a. Disconnect and then reconnect the sync cable.
b. Restart your computer.
USB
Multi-connector
Mac
Double-click the CD icon, and then
double-click palmOneDesktop.pkg.
Tip: During the installation process on a Windows computer,
you can select to synchronize with Outlook.
Already use a palmOne device?
To switch from synchronizing with Palm
Desktop software to Outlook, select Change
your synchronization method at the end of
the installation process.
®
icon appears in the group of icons in the lower-right part of
HotSync icon
2
Set up
a. Slide the power switch to the right.
b. Remove the stylus.
c. Follow the onscreen instructions
to set up your device.
Tip: Take the Quick Tour
more about the great features of
your device.
Problems? See Troubleshooting, below.
Get answers, learn more
Take the tutorial
Get more information
Done
Check your device:
1. Press the Home button twice, and then tap HotSync
2. In the HotSync application, make sure of the following:
– Local is highlighted. If it isn't highlighted, tap Local.
– Cradle/Cable appears. If not, tap the pick list, and then tap Cradle/Cable.
3. Tap the HotSync icon on the screen.
Local
HotSync icon
Cradle/Cable
Stylus
Power switch
to learn
Learn to use the popular features
of your device. Insert the
installation CD in your computer
and click here for an interactive
tutorial.
Open Palm Desktop software on
your computer and click Help.
Click here for the manual.
For more detail, go online:
www.palmOne.com/mylifedrive.
Click Online Support
(www.palmOne.com/support) for
the latest software updates and
answers to frequently asked
questions.
in Applications.