1. Manuals
  2. Brands
  3. MANDAKO Manuals
  4. Farm Equipment
  5. REDDI-ARM 10 Series
  6. Operator's manual

MANDAKO REDDI-ARM 10 Series Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Reddi-Arm Operator's Manual
OPERATORS MANUAL
OPERATORS MANUAL
Mandako Agri Marketing (2010) Ltd.
REDDI-ARM
10 SERIES
Page 1

Advertisement

Table of Contents
loading

Related Manuals for MANDAKO REDDI-ARM 10 Series

Summary of Contents for MANDAKO REDDI-ARM 10 Series

  • Page 1 Reddi-Arm Operator’s Manual REDDI-ARM 10 SERIES OPERATORS MANUAL OPERATORS MANUAL Mandako Agri Marketing (2010) Ltd. Page 1...
  • Page 2 During the one (1) year warranty period, provided that written notice of the Covered Defects is given to MANDAKO within seven (7) days from the date that the defect was, or ought to have been, discovered, the liability of MANDAKO under this Limited Warranty shall be limited to the repair or replacement of any defective Product.

  • Page 3: Table Of Contents

    4.1.1 Grease: ................... 40 4.1.2 Storing Lubricants: ..............40 4.1.3 Oil: ................... 40 4.1.4 Greasing: ................40 4.2 Servicing Intervals ..............41 4.2.1 Initial or rebuilt after 50 hours of use ........ 41 Page 3 Mandako Agri Marketing (2010) Ltd.
  • Page 4 4.2.5 Every 3 years ................43 4.3 Service Record ................44 Section 5: Troubleshooting ..............46 Section 6: Sign-off form................48 Section 7: REFERENCE................50 7.1 Bolt Torque ..................50 7.2 Tire Pressure ..................50 7.3 Hydraulic fitting torque ..............51 7.4 Mechanical specifications .............52 Mandako Agri Marketing (2010) Ltd. Page 4...
  • Page 5 Reddi-Arm Operator’s Manual Page intentionally left blank Page 5 Mandako Agri Marketing (2010) Ltd.

  • Page 6: Section 1: Introduction

    Congratulations on your choice of a Mandako Reddi-Arm. This equipment has been designed and manufactured to meet the needs of your operation. Safe, efficient, and trouble free operation of your Mandako Reddi-Arm requires that you and anyone else who will be using or maintaining the Reddi-Arm, read and understand the safety, operation, maintenance, and troubleshooting information contained within this manual.
  • Page 7 Reddi-Arm Operator’s Manual Page intentionally left blank Page 7 Mandako Agri Marketing (2010) Ltd.

  • Page 8: Section 2: Safety

    It may also be used to alert against unsafe practices. attention AttentIOn - Indicates practices or situations which may result in the malfunction of, or damage to, the equipment. Mandako Agri Marketing (2010) Ltd. Page 3 Mandako Agri Marketing (2010) Ltd. Page 8...

  • Page 9: Safety Orientation

    You are responsible for the SAFE operation and • Read and understand the Operator’s maintenance of your Mandako Reddi-Arm. Ensure that Manual and all safety signs before using, you and anyone else who will use, maintain or work maintaining, adjusting or cleaning the around the Reddi-Arm be familiar with the Safety, Reddi-Arm.

  • Page 10: Equipment Safety Guidelines

    Keep all shields in place. If shield removal becomes necessary for NOTE: repairs, replace the shield prior to use. Call Mandako directly if you are unfamiliar with who your local dealer/distributor is. • Replace any safety or instructional signs that are missing or illegible.

  • Page 11: Safety Training

    Always wear a seat belt. Serious injury or even death could result from falling off the tractor. If a roll-over occurs, the operator could be pinned under the ROPS or inside the tractor. Page 11 Mandako Agri Marketing (2010) Ltd.

  • Page 12: Operating Safety

    Before applying pressure to the hydraulic system, make sure all components are tight and that steel lines, hoses and couplings are in good condition. • Center machine and install frame lock pin before transporting or storing. Mandako Agri Marketing (2010) Ltd. Page 12...

  • Page 13: Maintenance Safety

    • When completing a maintenance or service function, make sure all safety shields and devices are installed before placing unit in service. Page 13 Mandako Agri Marketing (2010) Ltd.

  • Page 14: Transport Safety

    Do not exceed 32 km/h (20 mph) on highway transport. Reduce speed on rough roads and surfaces. • Always use hazard warning flashers on tractor when transporting unless prohibited by law. • Do not drink and drive. Mandako Agri Marketing (2010) Ltd. Page 14...

  • Page 15: Safety Decal Locations

    If safety decals have been damaged, removed, become illegible, or replacement parts do not have the decal, new ones must be applied. Safety decals are available from your authorized dealer. Mandako reserves the right to update safety decals without notice. Safety decals may not be to scale or exactly as shown.
  • Page 16 - Keep all components in good repair. R9913113 R9913110 Part No. R9913110 (E) Part No. R9913113 (F) Part No. R9913111 Part No. R9913110 Part No. R9913111 Part No. R9913110 Mandako Agri Marketing (2010) Ltd. Page 16...
  • Page 17 Remember - Safety Decals are for your protection! If they have been damaged, removed, become illegible, or replacement parts do not have the decal; new ones must be applied. Safety decals are available from your authorized dealer. Part No. R9913004 (G) Part No. R9913002 (H) Part No. R9913003 (I) Page 17 Mandako Agri Marketing (2010) Ltd.
  • Page 18 Reddi-Arm Operator’s Manual (C) (E) (D) (B) (I) (F) Mandako Agri Marketing (2010) Ltd. Page 18...
  • Page 19 Reddi-Arm Operator’s Manual Page intentionally left blank Page 19 Mandako Agri Marketing (2010) Ltd.

  • Page 20: Section 3: Operation

    This manual will describe how to set the Reddi-Arm to provide maximum field efficiency. By following the operating instructions in conjunction with a good maintenance program, your Reddi-Arm will provide many years of trouble-free service. Mandako Agri Marketing (2010) Ltd. Page 20...

  • Page 21: Machine Components

    Reddi-Arm Operator’s Manual 3.1 MACHINE COMPONENTS The main components of the unit are as follows: The Mandako Reddi-Arm acts as a link between a a. Main Frame tractor and a rotary mower giving the operator a greater b. Rear Axle reach without putting themselves in unsafe positions.
  • Page 22 Reddi-Arm Operator’s Manual (T) (U) Mandako Agri Marketing (2010) Ltd. Page 22...
  • Page 23 Reddi-Arm Operator’s Manual Page 23 Mandako Agri Marketing (2010) Ltd.

  • Page 24: Machine Break-In

    3.2 MACHINE BREAK-IN 3.3 PRE-OPERATION CHECKLIST There are no operational restrictions on the Reddi-Arm Efficient and safe operation of the Mandako Reddi-Arm when used for the first time. requires that each operator reads and understands the procedures, and all related safety precautions outlined in It is recommended that the following mechanical items this section.

  • Page 25: Equipment Matching

    Always secure the mounting pins with retainers. 6. PTO: A tractor with a 1000 RPM PTO is required. Either 21 spline, 1 inch or 20 spline, 1 inch yokes are available. Fig. 5 3-Point Hitch Page 25 Mandako Agri Marketing (2010) Ltd.

  • Page 26: Driveline Dimension

    2 parts and inspect for burrs or cuttings on the shaft ends. Be sure it telescopes freely before installing. Remeasure distance “A” in Fig. 8 to verify collapsed length. Mandako Agri Marketing (2010) Ltd. Page 26...

  • Page 27: Controls

    The system is designed with optional 3 or 4 circuits which control the following: a. Wheel axle position. b. Mower deck height. Mower wings. Fig. 11 Selector Valve Fig. 12 Selector Valve Control Box Page 27 Mandako Agri Marketing (2010) Ltd.

  • Page 28: Attaching Reddi-Arm To Tractor

    Install the mounting pin through the left arm and secure with the retainer. 8. Repeat with the right arm. Fig. 15 Aligning 3-Point Arms 9. Raise the 3-point hitch to remove the weight from the jack. Fig. 16 Aligning/Secured Mandako Agri Marketing (2010) Ltd. Page 28...

  • Page 29: Connect Pto

    Pull on the yoke to be sure it is locked in position. Attach the driveline shield anchor chain on both ends to an adjacent component to hold it in place. Fig. 20 Connected/Anchor Chain Page 29 Mandako Agri Marketing (2010) Ltd.

  • Page 30: Connect Hydraulic System

    3.7.4 Connect Lights 1. Connect the wiring harness by inserting terminal into plug on tractor. Route harness properly to prevent harness from dragging on the ground. 2. Check light function. Fig. 24 Wiring Harness Mandako Agri Marketing (2010) Ltd. Page 30...

  • Page 31: Connect Optional Hydraulic Selector Valve System

    Unplug the control wires at the terminal to remove switch assembly. 5. Plug assembly plug into terminal on control wiring harness. 6. Reverse the above procedure when unhooking. Page 31 Mandako Agri Marketing (2010) Ltd.

  • Page 32: Attaching Mover To Reddi-Arm

    1. Connect the wiring harness by inserting terminal into plug on rear frame of Reddi-Arm. Route harness properly to prevent harness from dragging on the ground. 2. Check light function. Fig. 30 Lights Connected Mandako Agri Marketing (2010) Ltd. Page 32...

  • Page 33: Connect Hydraulics

    Pull on the yoke to be sure it is locked in position. Attach the driveline shield anchor chain on both ends to an adjacent component to hold it in place if needed. Fig. 34 PTO Connected Page 33 Mandako Agri Marketing (2010) Ltd.

  • Page 34: Operation

    Fig. 36 Transport Steering Lock: Engaged Fig. 37 Transport Steering Lock: Disengaged 8. Use the wheel axle cylinder to set the angle of the wheels appropriate for the application. Fig. 38 Wheel Angle Mandako Agri Marketing (2010) Ltd. Page 34...
  • Page 35 There are many things that could be an obstacle in the ditch, including but not limited to: highway signs, culverts, rocks, debris, etc. Use the same procedure as described in ‘Side Roads’ to avoid all obstacles. Page 35 Mandako Agri Marketing (2010) Ltd.
  • Page 36 Slow down to avoid obstacles and obstructions to prevent damaging the machine or the mower. d. Do not use PTO shaft adaptors at any time. Mandako Agri Marketing (2010) Ltd. Page 36...

  • Page 37: Transporting

    Reddi-Arm Operator’s Manual 3.10 TRANSPORTING Mandako Reddi-Arms are designed to be easily and conveniently moved from field to field. When transporting, follow this procedure: 1. Clear the area of bystanders, especially small children. 2. Be sure the Reddi-Arm is properly attached to the tractor (see section 3.7).

  • Page 38: Storage

    12. Do not allow children to play on or around stored Reddi-Arm. 13. Apply a rust inhibitor or heavy grease to the exposed hydraulic cylinder rams to prevent rusting. Remove inhibitor or grease before using machine again. Mandako Agri Marketing (2010) Ltd. Page 38...

  • Page 39: Removing From Storage

    4. Lubricate all grease fittings as per section 4.2. 5. Clean rust inhibitor or grease from exposed cylinder ram ends 6. Replace any worn or defective parts. Go through the pre-operation checklist (see Section 3.3) before using unit. Page 39 Mandako Agri Marketing (2010) Ltd.

  • Page 40: Section 4: Service And Maintenance

    4.1.3 Oil: 3. Replace and repair broken fittings immediately. Mandako requires SAE 80W/90 gear oil for all gearboxes or SAE 80W/140 synthetic gear oil. Use SAE 80W/140 4. If fittings will not take grease, remove and clean synthetic gear oil to lower oil temperatures and prolong thoroughly.

  • Page 41: Servicing Intervals

    CV Ball & Socket 3. Check wheel bolt torque. (See section 7.1 for specs) CV Center Housing Guard Bushing Fig. 48 Reference Table Fig. 49 Driveline Grease Locations Fig. 50 Driveline Grease Locations Page 41 Mandako Agri Marketing (2010) Ltd.

  • Page 42: Every 40 Hours Or Weekly

    Fig. 53 Gearbox Plugs 4.2.3 Every 40 Hours or weekly 1. Remove any debris. Clean and wash machine. 2. Grease Rear Axle Pivot Pin with 10-15 pumps of grease. Fig. 54 Rear Axle Pivot Pin Mandako Agri Marketing (2010) Ltd. Page 42...

  • Page 43: Annually

    4.2.5 Every 3 years 1. Rebuild wheel hubs. a. Dissassemble b. Clean Inspect all bearings races and seal d. Replace worn or damaged parts e. Repack with fresh grease Assemble Fig. 55 Level Plug - Upper/Lower Page 43 Mandako Agri Marketing (2010) Ltd.

  • Page 44: Service Record

    Check gearbox oil EVERY 40 HOURS OR WEEKLY Remove debris, clean machine Grease rear axle pivot pin ANNUALLY Grease Jack Replace oil in gearboxes Re-torque all bolts EVERY 3 YEARS Rebuild Wheel Hubs Mandako Agri Marketing (2010) Ltd. Page 44...
  • Page 45 Check gearbox oil EVERY 40 HOURS OR WEEKLY Remove debris, clean machine Grease rear axle pivot pin ANNUALLY Grease Jack Replace oil in gearboxes Re-torque all bolts EVERY 3 YEARS Rebuild Wheel Hubs Page 45 Mandako Agri Marketing (2010) Ltd.

  • Page 46: Section 5: Troubleshooting

    Check oil level and drain to the appropriate level (Section 4.2.2) Selector Valve not working Not connected Check all connections and ensure they are properly connected Solenoid not activating Check wiring and solenoid using 12V and replace if necessary. Mandako Agri Marketing (2010) Ltd. Page 46...
  • Page 47 Reddi-Arm Operator’s Manual Page intentionally left blank Page 47 Mandako Agri Marketing (2010) Ltd.

  • Page 48: Section 6: Sign-Off Form

    Reddi-Arm Operator’s Manual SECTION 6: SIGN-OFF FORM Mandako Agri Marketing (2010) Ltd. follows the general Safety Standards specified by the American Society of Agricultural and Biological Engineers (ASABE), and the Occupational Safety and Health Administration (OSHA). Anyone who will be operating and/or maintaining the unit must read and clearly understand all Safety, Operating and Maintenance information presented in this manual.
  • Page 49 Reddi-Arm Operator’s Manual Sign Off Form (Continued) DATE EMPLOYEE’S SIGNATURE EMPLOYER’S SIGNATURE Page 49 Mandako Agri Marketing (2010) Ltd.

  • Page 50: Section 7: Reference

    SECTION 7: REFERENCE 7.2019 3-Plex Land Roller Operator’s Manual For information not included here, or for a digital copy of this manual, please call your dealer, or Mandako directly for assistance (1-888-525-5892). 7.2 bolT ToRQUe Specifications may change without notice.

  • Page 51: Hydraulic Fitting Torque

    1 3/16 - 12 65-70 90-95 1 7/16 - 12 92-100 125-135 1 11/16 - 12 125-140 170-190 2 - 12 150-165 200-225 For reference only, Source: Air-Way Manufacturing Co. - Carbon Steel Hydraulic Page 51 Mandako Agri Marketing (2010) Ltd.

  • Page 52: Mechanical Specifications

    12” x 8” x 0.250” W Hitch Hookup Type 3-Point (Cat 2 or Cat 3) Tires 320/70R15 / 440/55R18 Hub/Spindle Assembly 8-Bolt / 10-Bolt Drivelines Weasler (Cat 6) Gearbox Ratio PTO Requirements 1000 RPM Mandako Agri Marketing (2010) Ltd. Page 52...
  • Page 53 PART #: R9912020 RELEASED: JANUARY 01, 2022 Box 379 | 12159B Hwy 306 Plum Coulee, MB R0G 1R0 (888) 525-5892 info@mandako.com www.mandako.com MANDAKO AGRI MARKETING (2010) LTD. MANDAKO AGRI MARKETING (2010) LTD. Printed in Canada Mandako Agri Marketing (2010) Ltd. Page 53...

Table of Contents