Rossmax SA210 - Handheld Pulse Oximeter Manual

Intoduction

Rossmax Handheld Pulse Oximeter is used to measure oxygen saturation in blood (SpO2) and pulse rate, also to issue warnings immediately. It is a non-invasive device intended for spot-check of adults, child, and infants with corresponding probe applied at home, hospital and clinics. The probe contains a dual light source and a photodetector.

Consult the accompanying documents. Please read this manual carefully before use. Please be sure to keep this manual.

Name/ Functions of each part

No.	Item	Purpose
1	Pulse strength
2	Probe icon
3	LCD backlight button	For light on/ off
4	Sound button	For Heartbeat sound loud volume lower volume silence
5	Time	Shows the time
6	SpO2 %SpO2 icon	High SpO2 Low SpO2
7	Pulse Rate	High Pulse Rate Low Pulse Rate
8	UP/DOWN button	For adjust/view all setting/ memory memory icon
9	Set button	For view/ adjust default setting
10	Alert button	Alert off / Alert pause
11	Power button	Power on/ off
12	Battery compartment	For install or replace batteries Full batteries out of batteries
13		it's for data transmission.

Battery installation

1. Use thumb to slide battery cover out.
2. Insert or replace 4 "AA" batteries according to the (+/-) polarity.

Need to replace when the batteries icon " " is blinking on display/ while pressed the function button and nothing appears on display.

Batteries may leak or explode if used or disposed of improperly. Remove batteries if the device will be stored for long time. Do not use different types or brand of batteries at the same time.

Probe connection

Rossmax PA100/ PC100 or compatible probe is used. (Please install carefully.)

It may damage the efficiency of the device if not apply with a Rossmax compatible probe.

How to measure

1. Press the Power On button for 1 second, when the device activates, the beep sound will last for 2 second.
   Note: After the device activates, the software version will pop up directly. For first SA210 All symbols time activates, it will directly jump to time setting. (Please refer to setting instruction.)
2. Information of software version appears; insert one finger to probe, nail side up, SA210 All symbols for self-test.
   Notes: The device will turn itself off automatically after 1 minute idling with two beep sounded.
3. The pulse strength shows " ", pulse oximeter begins its measurement.
   Notes: The heartbeat is sounded though the buzzer. If need to become silence mode, press the sound button and the LCD screen will have the sound icon shown. If need the heartbeat sound, press the sound button to exit.
4. Your SpO2 and pulse rate values will appears on the screen after few seconds.

Notes:

1. Don't remove your finger until the measurement is completed.
2. Any other problems or unrecognized icon, please refer to trouble shooting.

Preview Default Setting

1. Press the button 1 second to preview default setting value.
2. Press to exit preview default mode or wait for 3 second for automatically.

How to Change Default Setting

Press the button 2 second to enter the set up mode and change default. For jump to next setting, press after finishing. To exit, press or wait for 10 second.

SPO2 mode

• To setup Max SpO2 rate, press to enter, and it shows as picture and press button for adjustment. To set up Min SpO2 rate, press , and it shows as picture and same as max setting.

Pulse Rate mode

• To setup Max Pulse rate, press to enter, and it shows as picture and press button for adjustment. To set up Min Pulse rate, press , and it shows as picture and same as max setting.
  

Memory interval mode

1. Optional of SA210: 5 / 10 / 30 / 60 minutes.
2. While the memory mode, the memory interval mode appears on the screen. To change the default, press to change (5)-(10)-(30)-(60) or (60)- (30)-(10)-(5) minutes.

Sound volume control

• For the control of sound volume, for loud volume, for lower volume. To change the sounds volume, Press to change --> .

Time Setup

• To set up the time, it starts from year as picture, and press to adjust. Following the same frequency for month, date, hour to minutes.

Press or wait for 10 seconds to exit, the setup value will be reserved. Please check the setting value before use.

Memories reading and delete

Enter the memory mode with the or to read the SpO2 and pulse rate in memory mode.

Note: When entering the memory reading mode, the will appear on the screen.

Press for two second during the memory reading mode, it will enter the memory delete mode. The screen show and means not to delete any data, while the screen withand, it means to delete data.

The deleted data could not be restored.

Audio Signals

No	Name	LCD Display	Sound	Control
1	Power on	All symbols software version start measure	Beep for 2 second	Press for 1 second
2	Pulse search	The icon flickers	X	X
3	Max./ Min SpO2 and Pulse rate warning	orand yellow backlight flickers	Beep-beep sounded repeatedly	Default
			Mute for temporary, will beep-beep sounded after two minutes.	mode
			Mute before power off	mode
4	Probe failure alert	shows on the screen and yellow back light flicker	Beep-beep sounded repeatedly	X
5	Low battery alert	shows on the screen and yellow backlight flickers.	Beep-beep-beep sounded repeatedly for 1 minute and power off/	x
6	Automatic Off	X	Beep-beep sounded and then power off	After pulse is undetectable for around 1 minutes.
7	Unable measure	Blood saturation & pulse rate appears (- -) and yellow backlight flickers.	Beep-beep sounded repeatedly.	X
8	Data Updated Period	Less than 2 seconds.	X	X
9	Alert Condition Delay	Less than 8 seconds for SpO2. Less than 16 seconds for pulse rate.	X	X
10	Alert Signal Delay	Less than 1 second for SpO2 and pulse rate	X	X

Specification

Troubleshooting

Symptoms	Check points	Corrections
SpO2 or Pulse rate cannot displayed	The icon "- -" shows on the screen	Place the finger properly and try again
	This icon shows on the screen means probe dysfunction	Be sure"Rossmax" probe is connected to the device correctly.
	Applied finger improperly	Place the finger properly and try again
SpO2 or Pulse rate are not displayed stably	Finger is shaking or body is moving	Keep body steady
	Applied finger improperly	Place the finger properly and try again
No display when the bottom is pressed	Batteries run down	Replace with new batteries
	Batteries inserted incorrectly	Re-insert batteries
The display disappears suddenly	The device will auto power off when it gets no signal	Normal
	Low battery	Replace with new batteries

Note: If the unit does not work, return it to your dealer. Under no circumstance should you disassemble and repair the unit by yourself.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Rossmax SA210 - Handheld Pulse Oximeter Manual