Edwards Drystar GV80 Instruction Manual
  1. Manuals
  2. Brands
  3. Edwards Manuals
  4. Enclosure
  5. Drystar GV80
  6. Instruction manual

Edwards Drystar GV80 Instruction Manual

Acoustic enclosure
Hide thumbs Also See for Drystar GV80:
Table of Contents

Advertisement

Quick Links

A505-75-880
Issue B Original
Instruction Manual
Drystar® GV80 Acoustic Enclosure
Description
Item Number
GV80 Acoustic Enclosure
A505-75-000

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Drystar GV80 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Edwards Drystar GV80

Summary of Contents for Edwards Drystar GV80

  • Page 1 A505-75-880 Issue B Original Instruction Manual Drystar® GV80 Acoustic Enclosure Description Item Number GV80 Acoustic Enclosure A505-75-000...

  • Page 3: Table Of Contents

    Fit the GV80 pump to the base assembly ................7 Connect the cooling-water and nitrogen pipelines ..............9 Fit a Swagelok fitting ....................16 Retighten a Swagelok fitting ..................16 © Edwards Limited 2007. All rights reserved. Page i Edwards and the Edwards logo are trademarks of Edwards Limited.
  • Page 4 Associated publications Publication title Publication number Vacuum pump and vacuum system safety P400-40-100 Trademark credits Swagelok™ is trademark of Crawford Fitting Company. Page ii © Edwards Limited 2007. All rights reserved. Edwards and the Edwards logo are trademarks of Edwards Limited.

  • Page 5: Introduction

    With the exception of the base assembly, all of the panels are made from mild steel and have acoustic foam on the interior surface(s). © Edwards Limited 2008. All rights reserved. Page 1 Edwards and the Edwards logo are trademarks of Edwards Limited.

  • Page 6: Acoustic Enclosure

    3. Right-hand side panel 7. Cable-gland 11. Left-hand side panel 4. Inlet partition 8. Base assembly 12. Front panel 13. Catch Page 2 © Edwards Limited 2008. All rights reserved. Edwards and the Edwards logo are trademarks of Edwards Limited.

  • Page 7: Technical Data

    Suitable for 1/2 inch outside diameter tube Nitrogen inlet connector Suitable for 1/4 inch outside diameter tube Electrical supply cable-gland PG29 © Edwards Limited 2008. All rights reserved. Page 3 Edwards and the Edwards logo are trademarks of Edwards Limited.
  • Page 8 A505-75-880 Issue B Page 4 © Edwards Limited 2008. All rights reserved. Edwards and the Edwards logo are trademarks of Edwards Limited.

  • Page 9: Installation

    If the Acoustic Enclosure is not to be used immediately, replace any packing and protective covers and store in suitable conditions, as described in Section 5.1. © Edwards Limited 2008. All rights reserved. Page 5 Edwards and the Edwards logo are trademarks of Edwards Limited.

  • Page 10: Fit The Pump To The Base Assembly

    9. Use the other two 1/2 inch tube inserts (6) to fit the other length of 1/2 inch outside diameter vinyl tube (7) between the GV pump inlet banjo fitting (14) and the cooling-water inlet connector (9) on the base assembly. Page 6 © Edwards Limited 2008. All rights reserved. Edwards and the Edwards logo are trademarks of Edwards Limited.

  • Page 11: Fit The Gv80 Pump To The Base Assembly

    7. Castor 8. M8 bolt and washer 9. Vibration isolator 10. Earth (ground) stud 11. Shake-proof washer 12. Nut 13. Plain washer © Edwards Limited 2008. All rights reserved. Page 7 Edwards and the Edwards logo are trademarks of Edwards Limited.

  • Page 12: Fit The Acoustic Panel

    8. Connect your cooling-water return pipeline to the cooling-water outlet (2) on the services panel (1). 9. Connect your nitrogen supply pipeline to the nitrogen inlet (4) on the services panel. Page 8 © Edwards Limited 2008. All rights reserved. Edwards and the Edwards logo are trademarks of Edwards Limited.

  • Page 13: Connect The Cooling-Water And Nitrogen Pipelines

    4. Nitrogen inlet 9. Cooling-water inlet fitting 14. Pump water inlet banjo fitting 5. Pump outlet elbow 10. Nitrogen inlet fitting © Edwards Limited 2008. All rights reserved. Page 9 Edwards and the Edwards logo are trademarks of Edwards Limited.
  • Page 14 A505-75-880 Issue B Page 10 © Edwards Limited 2008. All rights reserved. Edwards and the Edwards logo are trademarks of Edwards Limited.

  • Page 15: Maintenance

    Check that the pump is level and is supported on the levelling feet, and that the lock-nuts on the levelling  feet are tight. Check that the catches on the panels are secure.  © Edwards Limited 2008. All rights reserved. Page 11 Edwards and the Edwards logo are trademarks of Edwards Limited.
  • Page 16 A505-75-880 Issue B Page 12 © Edwards Limited 2008. All rights reserved. Edwards and the Edwards logo are trademarks of Edwards Limited.

  • Page 17: Storage And Disposal

    Disposal Dispose of the Acoustic Enclosure and any components safely in accordance with all local and national safety and environmental requirements. © Edwards Limited 2008. All rights reserved. Page 13 Edwards and the Edwards logo are trademarks of Edwards Limited.
  • Page 18 A505-75-880 Issue B Page 14 © Edwards Limited 2008. All rights reserved. Edwards and the Edwards logo are trademarks of Edwards Limited.

  • Page 19: Appendix A1 Correct Use Of Swagelok Connectors

    3. Use a wrench or spanner to turn the nut (4) to its original position (you will feel an increase in resistance when the nut is in its original position), then tighten the nut slightly. © Edwards Limited 2008. All rights reserved. Page 15 Edwards and the Edwards logo are trademarks of Edwards Limited.

  • Page 20: A1 Fit A Swagelok Fitting

    Figure A2 - Retighten a Swagelok fitting 1. Swagelok connector 2. Front (tapered) ferrule 3. Rear ferrule 4. Nut 5. Tube Page 16 © Edwards Limited 2008. All rights reserved. Edwards and the Edwards logo are trademarks of Edwards Limited.
  • Page 21 This page has been intentionally left blank.
  • Page 22 This page has been intentionally left blank.
  • Page 23 Download the latest documents from www.edwardsvacuum.com/HSForms/, follow the procedure in HS1, fill in the electronic HS2 form, print it, sign it, and return the signed copy to Edwards. Note: If we do not receive a completed HS2 form, we will not accept the return of the...
  • Page 24 edwardsvacuum.com...

Table of Contents